冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

钛铜复合棒及其标准化

概述了钛铜复合棒研制开发及发展历程,并介绍了钛铜复合棒的主要性能,以及钛铜复合棒的标准化情况。     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

Strain waves in colliding bars having nonparallel faces

The paper reports the experimental investigation data for the effect that nonparallel faces of bars under impact exert on the parameters of longitudinal and bending strain waves generated in the bars. The changes in stress magnitudes in the bar under impact with growing angle of the impact faces offset are described. __________ Translated from Fiziko-Tekhnicheskie Problemy Razrabotki Poleznykh Iskopaemykh, No. 6, pp. 73–78, November–December, 2006.     

锌加(ZINGA)防腐钢筋在杭州湾跨海大桥施工中的应用

杭州湾跨海大桥在极其复杂的海洋环境下施工，外露钢筋极易腐蚀，锌加钢筋能提高钢筋的抗腐蚀能力，本文简介锌加防腐钢筋在大桥施工中的应用情况。     

论“TBSA”空间分析程序的合理应用

本文旨在提出应用多层及高层建筑结构空间分析程序“TBSA”的局限性及其分析结果的合理使用。     

Stress concentration and fatigue of profiled reinforcing steels

Stress concentrations arise from profiles of ribbed reinforcing steel bars and in this study the results of calculated stress concentration factors (SCF), by using finite element method, are related to the fatigue test results. It is apparent that the degree of confinement of a ribbed bar embedded in concrete not only affects the magnitude of the ultimate bond stress but also the bond stress-slip relation. Thus the rib geometry or profile pattern is designed for optimum bond characteristics and not for fatigue considerations. However the rib geometry influences the fatigue performance through the SCFs arising from the root radius, width and flank angles of the profiles. It is shown that these latter factors have a significant influence on the fatigue behaviour of reinforcing steel bars.     

考虑剪切变形的轴心受压GFRP圆管临界荷载

为了考虑剪切变形对玻璃纤维增强复合材料（GFRP）构件屈曲荷载的影响,利用Engesser剪切变形理论,推导考虑剪切变形和初弯曲的临界荷载. 应用于GFRP圆管时,考虑材料各向异性特征对剪切系数及强度的影响. 对4根具有不同长细比的GFRP圆管试件进行轴压试验. 结果表明,GFRP圆管在截面强度估算时应综合考虑轴向纤维压缩破坏和环向基体拉伸破坏. 所推导的临界荷载计算式的结果和试验结果吻合良好.     

Joining of metal bars by a new process of transformation-diffusion brazing

Within the bonded interface of metal bars joint produced by conventional solid state bonding process （ such as flash welding, resistance butt welding, friction welding and so on）, the inclusions are often present, which degrade the ductility of joint. A new process of transformation-diffusion brazing is proposed, in which an amorphous foil containing melting point depressant is preplaced between the interfaces to be joined, and the assembly is repeatedly heated/cooled without holding time at peak temperature. A low carbon steel bars, BNi-2 amorphous foil and resistance butt welding machine were used. The results show that surfuce contamination can be disrupted by the dissolution of base metal into molten interlayer in comparison with conventional process, and the ductility of joint can be improved by increasing the times of temperature cycles on line. In addition, transformation-diffusion brazing can be done with relatively simple and inexpensive system in comparison with transient liquid phase bonding.     

人工智能在冷轧带肋钢筋工艺参数优化中的应用

论述了人工智能在冷轧带肋钢筋工艺参数优化中的应用,首先利用神经网络建立起冷轧带肋钢筋工艺参数与产品抗拉强度之间关系的数学模型,然后用遗传算法对工艺参数优化。按优化后的工艺参数在某拉丝加工厂进行了大批量生产试验,产品的合格率达到98%以上,从而为控制冷轧带肋钢筋工艺参数提供了一条行之有效的途径。