Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

Flame characteristics of premixed H2-air mixtures explosion venting in a spherical container through a duct

The explosion venting duct can effectively reduce the hazard degree of a gas explosion and conduct the venting energy to the safe area. To investigate the flame quantitative propagation law of explosion venting with a duct, the effects of hydrogen fraction and explosion venting duct length on jet flame propagation characteristics of premixed H₂-air mixtures were analyzed through experiment and simulation. The experiment results under initial conditions of room temperature and 1 atm show that when hydrogen fraction was high enough, part of the unburned hydrogen was mixed with air again to reach an ignitable concentration, resulting in the secondary combustion was easier produced and the duration of the secondary flame increased. With the increase of venting duct length, the flame front distance and propagation velocity increased. Meanwhile, the spatial distribution of pressure field and temperature field, and the propagation process and mechanism of the flame venting with a duct were analyzed using FLUENT software. The variation of the pressure wave and the pressure reflection oscillation law in the explosion venting duct was captured. Therefore, in the industrial explosion venting design with a duct, the hazard caused by the coupling of venting pressure and venting flame under different fractions should be considered comprehensively.     

Deposition of UF5 on the surface of steel material having oxide coating in contact with gaseous UF6

When UF6 is handled in leak tight system, the amount of uranium compound formed on the surface of containers, valves, and others in UF6 handling facilities is not so significant for a short term that special attention has not been given to this problem. The present work was done to throw some more light on this problem based on the recent experiment. We discuss the possibility that the intermolecular transfer of a fluorine atom from UF6 to UF5 may participate in the formation of uranium compound. The discussion includes also the unique features contained in the experimental result, the reaction processes assumed in this problem, and the derivation of a rate equation for expressing the deposition of uranium compound. Furthermore, we propose a new method for determining nonlinear parameters included in a governing differential equation having two variables for expressing the deposition of uranium compound from experimental raw data.     

Development and validation of a micro-fin tubes evaporator model using R134a and R1234yf as working fluids

This paper presents a model of shell and tube evaporator with micro-fin tubes using R1234yf and R134a. The model developed for this evaporator uses the ε-NTU method to predict the evaporating pressure, the refrigerant outlet enthalpy and the outlet temperature of the secondary fluid. The model accuracy is evaluated using different two-phase flow boiling correlations for micro-fin tubes and comparing predicted and experimental data. The experimental tests were carried out for a wide range of operating conditions using R134a and R1234yf as working fluids. The predicted parameter with maximum deviations, between the predicted and experimental data, is the evaporating pressure. The correlation of Akhavan– Behabadi et al. was used to predict flow boiling heat transfer, with an error on cooling capacity prediction below 5%. Simulations, carried out with this validated model, show that the overall heat transfer coefficient of R1234yf has a maximum decrease of 10% compared with R134a.     

A self‐scalable load injection service

Load testing of applications is an important and costly activity for software provider companies. Classical solutions are very difficult to set up statically, and their cost is prohibitive in terms of both human and hardware resources. Virtualized cloud computing platforms provide new opportunities for stressing an application's scalability, by providing a large range of flexible and less expensive (pay‐per‐use model) computation units. On the basis of these advantages, load testing solutions could be provided on demand in the cloud. This paper describes a Benchmark‐as‐a‐Service solution that automatically scales the load injection platform and facilitates its setup according to load profiles. Our approach is based on: (i) virtualization of the benchmarking platform to create self‐scaling injectors; (ii) online calibration to characterize the injector's capacity and impact on the benched application; and (iii) a provisioning solution to appropriately scale the load injection platform ahead of time. We also report experiments on a benchmark illustrating the benefits of this system in terms of cost and resource reductions. Copyright © 2013 John Wiley & Sons, Ltd.     

丙烯酸/α-甲基丙烯酸/丙烯酰胺共聚物智能水凝胶的合成及评价

由丙烯酸（AA）、α-甲基丙烯酸（MAA）和丙烯酰胺（AM）合成了具有很好DH敏感性和一定温度敏感性的智能水凝胶，考察了合成温度、丙烯酰胺、交联剂和引发剂用量对制备的水凝胶溶胀性能的影响。结果表明，在60℃下，单体从和MAA用量分别为100mmol和75mmol时，单体AM、交联剂和引发剂用量分别为反应物总质量的32．8％、0．2％和0．4％时，制备的水凝胶溶胀性能最好。考察了介质的离子浓度、pH值和温度对水凝胶溶胀比的影响，结果表明，离子浓度越大，水凝胶的溶胀比越小；水凝胶具有一定的DH可逆性。     

Taxometrics in Psychopathology Research: An Introduction to Some of the Procedures and Related Methodological Issues.

This article introduces a special section on the use of taxometrics to examine the categorical versus the dimensional structure of various forms of psychopathology. Paving the way into the special section, this introduction briefly describes 3 taxometric methods--mean above minus below a sliding cut (MAMBAC), maximum covariation (MAXCOV), and maximum eigenvalue (MAXEIG)--and discusses possible threats to statistical conclusion validity that often emerge when such techniques are applied in psychopathology research. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A call admission and rate control scheme for multimedia support over IEEE 802.11 wireless LANs

Quality of service (QoS) support for multimedia services in the IEEE 802.11 wireless LAN is an important issue for such WLANs to become a viable wireless access to the Internet. In this paper, we endeavor to propose a practical scheme to achieve this goal without changing the channel access mechanism. To this end, a novel call admission and rate control (CARC) scheme is proposed. The key idea of this scheme is to regulate the arriving traffic of the WLAN such that the network can work at an optimal point. We first show that the channel busyness ratio is a good indicator of the network status in the sense that it is easy to obtain and can accurately and timely represent channel utilization. Then we propose two algorithms based on the channel busyness ratio. The call admission control algorithm is used to regulate the admission of real-time or streaming traffic and the rate control algorithm to control the transmission rate of best effort traffic. As a result, the real-time or streaming traffic is supported with statistical QoS guarantees and the best effort traffic can fully utilize the residual channel capacity left by the real-time and streaming traffic. In addition, the rate control algorithm itself provides a solution that could be used above the media access mechanism to approach the maximal theoretical channel utilization. A comprehensive simulation study in ns-2 has verified the performance of our proposed CARC scheme, showing that the original 802.11 DCF protocol can statically support strict QoS requirements, such as those required by voice over IP or streaming video, and at the same time, achieve a high channel utilization. Hongqiang Zhai received the B.E. and M.E. degrees in electrical engineering from Tsinghua University, Beijing, China, in July 1999 and January 2002 respectively. He worked as a research intern in Bell Labs Research China from June 2001 to December 2001, and in Microsoft Research Asia from January 2002 to July 2002. Currently he is pursuing the PhD degree in the Department of Electrical and Computer Engineering, University of Florida. He is a student member of IEEE. Xiang Chen received the B.E. and M.E. degrees in electrical engineering from Shanghai Jiao Tong University, Shanghai, China, in 1997 and 2000, respectively, and the Ph.D. degree in electrical and computer engineering from the University of Florida, Gainesville, in 2005. He is currently a Senior Research Engineer at Motorola Labs, Arlington Heights, IL. His research interests include resource management, medium access control, and quality of service (QoS) in wireless networks. He is a Member of Tau Beta Pi and a student member of IEEE. Yuguang Fang received a Ph.D degree in Systems and Control Engineering from Case Western Reserve University in January 1994, and a Ph.D degree in Electrical Engineering from Boston University in May 1997. From June 1997 to July 1998, he was a Visiting Assistant Professor in Department of Electrical Engineering at the University of Texas at Dallas. From July 1998 to May 2000, he was an Assistant Professor in the Department of Electrical and Computer Engineering at New Jersey Institute of Technology. In May 2000, he joined the Department of Electrical and Computer Engineering at University of Florida where he got the early promotion with tenure in August 2003 and has been an Associate Professor since then. He has published over one hundred (100) papers in refereed professional journals and conferences. He received the National Science Foundation Faculty Early Career Award in 2001 and the Office of Naval Research Young Investigator Award in 2002. He is currently serving as an Editor for many journals including IEEE Transactions on Communications, IEEE Transactions on Wireless Communications, IEEE Transactions on Mobile Computing, and ACM Wireless Networks. He is also actively participating in conference organization such as the Program Vice-Chair for IEEE INFOCOM’2005, Program Co-Chair for the Global Internet and Next Generation Networks Symposium in IEEE Globecom’2004 and the Program Vice Chair for 2000 IEEE Wireless Communications and Networking Conference (WCNC’2000).     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。