激光在材料中感生的瞬态光声波和光热波

研究了锁模激光在材料中产生频率达GHz的光声波和相应探测技术,用回波分析法无损坏测量了薄材料的厚度。研究了激光在材料中感生的光热波,热沉测量可用于解释材料的破坏机理。     

L波段窄脉宽500W固态功放组件的设计

介绍了作者研制的应用于固态雷达发射机上的L波段500W固态功放组件的工作原理、用途及其主要技术指标。描述了功放组件的设计过程和测试结果。该功放组件在窄脉宽条件下实现了快速上升沿,性能优良,工作稳定可靠。     

氮离子注入尼龙1010的摩擦学特性

用高能离子注入机对尼龙 10 10进行 N+注入改性 ,注入能量为 4 5 0 ke V,剂量分别为 5× 10 14 /cm2 、2 .5× 10 15/cm2 及 1.2 5× 10 16/cm2 。以 Zr O2 及 Si3N4 球为上球样 ,分别与注入尼龙 10 10下盘样组成摩擦副 ,在销盘摩擦试验机上评价它们在干摩擦条件下的摩擦磨损行为。结果表明 ,几种剂量的 N+注入均增强了尼龙 10 10的耐磨性。未注入样品的磨损主要表现为粘着、塑性变形、犁沟和疲劳脱层 ,注入样品的磨损主要为轻微的磨粒磨损。     

Study of the effective parameters on mechanical and electrical properties of carbon black filled PP/PA6 microfibrillar composites

In this study the electrical and mechanical properties of microfibrillar polypropylene (PP)/polyamide6 (PA6) blend filled with super conductive carbon black (CB) have been investigated. In situ microfibrillar PP/PA6 composites filled with CB are produced using a single screw extruder equipped with a spinneret. Glycidyl methacrylate (GMA) grafted polypropylene (PP-g-GMA) is used as the compatibilizer. To investigate the effects of extensional flow on the microstructure, electrical and mechanical properties, three adaptors with various convergence angles were designed, prepared and applied between the extruder and the spinneret. To optimize the effects of processing and material parameters on the electrical and mechanical properties, the Taguchi method of experimental design is used. Material and processing factors which are studied include: concentration of PA6, compatibilizer level, CB concentration, drawing speed of melt spinning line, adaptor angle, order of mixing and temperature profile along the extruder. The results show an increase in DC conductivity of up to 10¹¹ times in comparison with pure PA6, by increasing the concentration of CB, drawing speed, adaptor angle and optimizing other parameters. By optimizing processing and material factors studied here, strength of microfibrillar structured composites is increased of up to 80% in comparison to pure PP.     

Compatibility between Polyamide 6 and Polycarbonate

Polyamide （PA6） and polycarbonate （PC） were prepared by a Brabender mixer （ PLV- 151） at 240℃ with 30 rpm for duration of 8 and 6 minutes respectively. The epoxy resin （E） addition can lead to substantial microstructural changes in the PA6/PC blends. Scanning electron microscope （SEM） was used to observe the mixtures characterized by the domains of clearly segregated homophases and voids between the two polymers. PA6/PC of polyamide 6 and polycarbonate with epoxy resin addition under the composition ratio of 20/80, 20/80/1, 40/60/1 and 40/60, were tested to verify the key role of epoxy in promoting the compatibility of PA6 with PC during blending.     

空间激光通信系统精跟踪单元PZT驱动电源的设计

压电陶瓷驱动电源是压电陶瓷微位移器应用中的关键部件。PA85是一种高电压、高功率MOSFET的带宽运算放大器,采用双电源供电,输出电流高达200mA,输出电压更可高达±215V。该文详细介绍了基于PA85的一种电源复合放大器的设计及仿真,通过对各项性能指标的仿真表明,该驱动电源具有精度高、分辨率高、稳定性好、纹波小和电路结构简单等优点。     

玻纤增强PA66／PP合金的特性及应用

介绍玻纤增强ＰＡ６６／ＰＰ合金的制备工艺及特性，与纯尼龙６６树脂相比，加工性能好，综合性能优异。该材料适用于中小型油浸式变压器的分接开关及其它绝缘部件。     

低位真空冷却装置在磷酸系统中的应用

葛丰化工厂磷酸萃取槽反应热不能有效移出,限制了生产能力的提高,通过采用低位真空冷却装置移走反应热,并同时改造水循环系统。改造后,投矿浆量达16t/h〔矿浆w(H2O)35%〕,生产能力从技改前2.67tP2O5/h提高到4.56tP2O5/h,萃取温度稳定控制在83～85℃。由于结晶状况改善,萃取率、洗涤率分别提高达96.33%、99.04%,能耗从181.3kW·h/tP2O5降低到149.8kW·h/tP2O5,含氟废气排放量从30000m3/h减少到小于6000m3/h。     

三箱式纺丝技术生产PET/PA6复合纤维

介绍了采用三箱式纺丝技术生产PET/PA6复合纤维的设备及工艺。重点对纺丝箱体、纺丝温度控制进行了详细的讨论。     

连续聚合法生产高粘度PA6

介绍连续聚合法生产高粘度ＰＡ６的聚合工艺，特点及产品性能指标，并介绍了关键生产设备的特点及作用。