Thermomechanical stability and inelastic energy dissipation as durability criteria for fuel cell gas diffusion media with pre-assembly effects

In this article, pre-assembly hot-press pressure and thermal expansion effects in gas-diffusion layers (GDLs) are addressed to explore the practicalities of the constitutive model reported in the companion article. A facile technique is proposed to include deformation history dependent residual strain effects. The model is implemented in the numerical environment and compared with widely followed conventional models such as isotropic and orthotropic material models. With the normal and accelerated thermal expansion effects no significant variation in stresses or strains is reported with the compressible GDL model in contrast to the conventional incompressible form of the GDL model. The present work identifies the critical differences with advanced and extended variants of the model along with conventional GDL material models in terms of planar stress/strain distribution and the membrane response. Finally, the model is simulated for micro-cyclic stress loads of varying amplitudes that imitate the real working conditions of fuel cell. The inelastic energy dissipation in GDLs is predicted using the proposed model, which is utilized further to distinguish the safe (elastic) and unsafe (inelastic shakedown) operating limits. The inelastic collapse of GDLs is shown to be a active function of high amplitude micro-cyclic load with high initial clamping load.     

Experimental research on combined effect of obstacle and local spraying water fog on hydrogen/air premixed explosion

In order to reveal the mechanism of water fog explosion suppression and research the combined effect of water fog and obstacle on hydrogen/air deflagration, multiple sets of experiments were set up. The results show that the instability of thermal diffusion under lean combustion conditions is the main influencing factor of hydrogen/air flame surface instability, and the existence of water fog will aggravate the hydrogen/air flame surface instability. When obstacle is not considered, 8 μm, 15 μm, 30 μm water fog can significantly reduce the flame velocity and explosion overpressure of hydrogen/air, 45 μm fine water fog plays the opposite role. When considering the relative position of the water fog release position and the obstacle, the 8 μm, 15 μm, 30 μm water fog has almost no suppression effect when released near the obstacle, but a significant suppression effect occur, when using the 45 μm water fog. In the field of theoretical research, the research results not only provide an experimental basis for the fine water fog to reduce the consequences of hydrogen explosion accidents, and the optimal diameter range used by the water fog, but also provide experimental reference for the numerical simulation of hydrogen/air explosion suppression in semi-open space, and promote the development of hydrogen explosion suppression theory. In terms of engineering applications, this study can provide a theoretical basis for the layout of fire fighting equipment in the engine room of nuclear power plants or hydrogen-powered ships.     

Mass transfer in polycrystalline ytterbium monosilicate under oxygen potential gradients at high temperatures

Mass transfer in polycrystalline Yb₂SiO₅ wafers with precise composition control was evaluated and analyzed by oxygen permeation experiments at high temperatures using an oxygen tracer. Oxygen permeation proceeded due to mutual grain boundary diffusion of oxide ions and Yb ions without synergistic effects such as acceleration or suppression. The oxygen shielding properties of Yb₂SiO₅ were compared with those of the other line compounds such as Yb₂Si₂O₇ and Al₂O₃ based on the determined mass transfer parameters. It was found that the more preferentially an oxide ion diffuses in the grain boundary compared to the interior of the grain, the greater the effect of suppressing the movement of the oxide ion by applying an oxygen potential gradient becomes.     

Influence of pulse-jet cleaning pressure on performance of compact dust collector with pleated filter operated in clean-on-time mode

To operate a bag filter continuously, pulse-jet cleaning of dust particles from the filter medium is commonly required, and the pulse-jet pressure significantly affects the filter performance. In this study, the accumulation structure of residual dust particles inside and on the surface of a filter medium at different pulse-jet pressures was investigated by constructing a simple model, and the influence of the dust structure on the filter performance was clarified. Using a simple model, we determined the effective ratio of filtration area β, which represents the ratio of the filterable area to the total filtration area, the true resistance coefficient due to the primary dust layer ζ_p’ thinly deposited on the filter surface, and the true resistance coefficient inside the filter media itself ζ_f’_. The effective ratio of filtration area β decreased with operation time for all pulse-jet pressures; however, it maintained a high value when the pulse-jet pressure was high. The validity of β analyzed by the model was verified using two different methods, and the results showed good agreement, indicating that the model is effective in identifying real conditions. The true resistance coefficient due to the primary dust layer ζ_p’ decreased as the pulse-jet pressure increased; however, the true resistance coefficient inside the filter media itself ζ_f’ was the highest at 0.5 MPa. In addition, the dust collection efficiency was different at each pulse-jet pressure, which was considered to be caused by the difference in the dust particle accumulation structure.     

Comparative analysis of formaldehyde and toluene sorption on indoor floorings and consequence on Indoor Air Quality

Indoor surfaces may be adsorptive sinks with the potential to change Indoor Air Quality. To estimate this effect, the sorption parameters of formaldehyde and toluene were assessed on five floorings by an experimental method using solid-phase microextraction in an airtight emission cell. Adsorption rate constants ranged from 0.003 to 0.075 m·h⁻¹, desorption rate constants from 0.019 to 0.51 h⁻¹, and the partition coefficient from 0.005 to 3.9 m, and these parameters vary greatly from one volatile organic compound/material couple to another indicating contrasted sorption behaviors. A rubber was identified as a sink of formaldehyde characterized by a very low desorption constant close to 0. For these sorbent floorings identified, the adsorption rates of formaldehyde are from 2 to 4 times higher than those of toluene. Two models were used to evaluate the sink effects of floorings on indoor pollutant concentrations in one room from different realistic conditions. The scenarios tested came to the conclusion that the formaldehyde sorption on one rubber (identified as a sink) has a maximum contribution from 15% to 21% for the conditions of low air exchange rate. For other floorings, the sorption has a minor contribution less than or equal to 5%, regardless of the air exchange rate.     

应变纤锌矿ZnO/MgxZn1-xO量子点中离子施主束缚激子的光学性质

Within the framework of the effective-mass approximation and the dipole approximation, considering the three-dimensional confinement of the electron and hole and the strong built-in electric field(BEF) in strained wurtzite Zn O/Mg0:25Zn0:75O quantum dots(QDs), the optical properties of ionized donor-bound excitons(D+, X)are investigated theoretically using a variational method. The computations are performed in the case of finite band offset. Numerical results indicate that the optical properties of(D+, X) complexes sensitively depend on the donor position, the QD size and the BEF. The binding energy of(D+, X) complexes is larger when the donor is located in the vicinity of the left interface of the QDs, and it decreases with increasing QD size. The oscillator strength reduces with an increase in the dot height and increases with an increase in the dot radius. Furthermore, when the QD size decreases, the absorption peak intensity shows a marked increment, and the absorption coefficient peak has a blueshift. The strong BEF causes a redshift of the absorption coefficient peak and causes the absorption peak intensity to decrease remarkably. The physical reasons for these relationships have been analyzed in depth.     

亲子乐园空调送风方式的数值模拟研究

大型综合室内亲子乐园属于高大空间,设有游乐设施和游戏的特殊性使得对空间的舒适性要求一致,但是送风气流遇阻严重,室内存在较多气流死角,影响室内空气质量和儿童健康。因此其空调设计不仅需要考虑温度、风速的空间均匀度,还要考虑各点的空气龄和PMV-PPD指标。以天津某亲子乐园为研究对象,利用scSTREAM软件对适用于该房间的辐射供冷加新风、置换通风、混合通风三种空调方式的送风效果进行数值模拟分析,从流场的均匀性、人员的热舒适性等方面对模拟结果进行探讨,研究结果表明辐射供冷加新风方式的空间均匀性和PMV指标最佳,混合通风方式的空气龄最小。     

In situ efficiency of filters in residential central HVAC systems

High-efficiency filtration in residential forced-air heating, ventilation, and air conditioning (HVAC) systems protects equipment and can reduce exposure to particulate matter. Laboratory tests provide a measure of the nominal efficiency, but they may not accurately reflect the in situ efficiency of the filters because of variations in system conditions and changes in filter performance over time. The primary focus of this paper is to evaluate the effective filtration efficiency, which is inclusive of any loading and system impacts, in 21 occupied residential homes through in-duct concentration measurements. We considered the role of filter media by testing both electret and non-electret media, as well as the role of loading by considering new and used filters. The results show that filters with higher nominal efficiency generally had higher effective filtration efficiency in the same home. In terms of performance change, there is no significant difference in efficiency between initial and 3-month non-electret filters, but the efficiency of electret filters generally decreased over time. However, both nominal efficiency and performance change were vastly overshadowed by the wide variety in loading and system conditions across homes, making it hard to predict filter efficiency in a given home without in situ measurements.     

Nonlinear dynamic behaviors and control based on simulation of high-purity heat integrated air separation column

In this paper, the dynamic behaviors on the basis of simulation for high-purity heat integrated air separation column (HIASC) are studied. A nonlinear generic model control (GMC) scheme is proposed based on the nonlinear behavior analyses of a HIASC process, and an adaptive generic model control (AGMC) scheme is further presented to correct the model parameters online. Related internal model control (IMC) scheme and multi-loop PID (M-PID) scheme are also developed as the comparative base. The comparative researches are carried out among these linear and nonlinear control schemes in detail. The simulation research results show that the proposed AGMC schemes present advantages in both servo control and regulatory control for the high-purity HIASC.     

基于空气质量模拟的江苏省大气污染物排放清单比较研究

大气污染物排放清单是空气质量模拟和空气污染治理的重要依据.本研究比较分析了两套覆盖江苏省的2017年大气污染物排放清单，即分别由上海市环境科学研究院、江苏省环境科学研究院编制的"长三角清单"和"江苏省清单"，并结合区域空气质量模型CMAQ评估不同清单对长三角地区2017年1、4、7、10月的空气质量模拟的影响.清单比较结果表明，除二氧化硫（SO₂）以外，江苏省清单估算的各污染物排放量较长三角清单低.通过与观测数据比较，发现两套清单对SO₂、氮氧化物（NO_x）、臭氧（O₃）和细颗粒物（PM_2.5）的模型模拟性能均较好.江苏省清单与长三角清单两者的模拟结果空间分布接近，其中江苏省清单模拟的PM_2.5和O₃在长三角多数地区略低于长三角清单的模拟结果（1月O₃除外）.江苏省清单与长三角清单均能够用于空气质量模式模拟，可为江苏地区的细颗粒物和光化学烟雾污染的控制策略制定提供参考.