公路隧道喷射混凝土套拱加固结构力学特性

为研究喷射混凝土套拱加固前后二次衬砌与混凝土套拱的受力状况,依托陕西汉中至留坝段八里关隧道,运用有限元软件建立隧道混凝土结构套拱加固分析模型,并通过现场监测获取二次衬砌与套拱间的接触压力、套拱格栅拱架钢筋应力、套拱混凝土应力,将数值模拟结果与现场测试结果相结合,得出套拱结构的一般受力变化规律。结果表明:套拱加固前衬砌结构的最不利荷载位置位于施工缝附近的拱顶、拱肩与拱脚处; 由于衬砌局部变形与温度应力的影响,套拱混凝土应力变化呈现反复“上升-下降-上升”最后趋于稳定的特点; 套拱的作用是控制二次衬砌的进一步变形,套拱施作后所承受荷载较小,套拱反作用力远小于围岩作用于衬砌的应力,在应力计算中不应将衬砌与套拱作为整体计算; 套拱结构数值模拟所得的结果与现场测试套拱结构内力(轴力、弯矩)的大小及分布相似度高,但在衬砌裂损严重部位,数值模拟所得结果误差较大,应以现场测试结果为准。     

基于ANP-SWOT的上海公路废弃物资源化发展对策研究

随着公路系统的新陈代谢，大量废弃物给城市的资源与环境协调发展带来了巨大压力，以沥青路面再生技术为路径的公路废弃物资源化符合循环经济的理念，是我国公路建设迈向生态文明的必然选择。通过 ANP-SWOT 对上海公路废弃物资源化发展战略进行实证分析，发现当前形势下其优势和机遇较为明显，确定以 SO 策略为核心的推广战略为最佳选择，并提出一系列配套发展策略，为推动上海公路废弃物资源化提供参考。     

Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

公路边坡培植柠条的探讨

介绍了河曲公路所处的自然环境 ,阐述了人工铲草的利与弊 ,进而提出了边坡培植柠条的效益分析 ,并对培植柠条的苗期管理及与养护生产的关系进行了介绍     

真空联合堆载预压法加固软基实践研究

简要介绍了凫洲大桥南引道软基真空联合堆载预压处理方案,并对软基处理效果进行了分析,得出了真空联合堆载预压法施工工艺成熟,施工方法简单,能增加地基承载力的结论,可供类似工程参考。     

柔性纤维混凝土的疲劳特性研究

将柔性纤维掺入水泥混凝土可以大幅度提高混凝土的弯曲疲劳等路用性能,并通过试验建立了柔性纤维混凝土的疲劳方程.结果表明,柔性纤维不但能使混凝土的强度提高,更主要的是可以在重交通条件下,可成倍地提高混凝土的弯曲疲劳寿命.     

气囊在建筑施工中的应用

对气囊在路基压实密度检测、空心板梁制作和大型混凝土构件搬运中的运用进行了分析,指出将气囊这种先进的施工工艺应用到建筑施工中,加快了施工进度,确保了工程施工质量,并降低了工程施工成本,值得推广使用。     

陕西南部路基病害分布特征及主要控制因素探讨

在统计分析的基础上,归纳总结了陕西南部各类路基病害的分布特征,并从自然因素和人为因素两个方面分析了各类路基病害发生的主要控制因素。     

阳泉市煤矿采空区地质因素对公路的破坏

介绍了阳泉市煤矿采空区对公路建设所造成的危害，对其上覆岩层变形破坏的地质因素及其破坏机理作了分析，指出应该采取各种措施减少对公路的破坏。     

Assessment of Highway Bridge Upgrading by Dynamic Testing and Finite-Element Model Updating

The Land Transport Authority of Singapore has a continuing program of highway bridge upgrading for refurbishing and strengthening bridges to allow for increasing vehicle traffic and increasing axle loads. One subject of this program has been a short-span bridge taking a busy main road across a coastal inlet near a major port facility. Experiment-based structural assessments of the bridge were conducted before and after upgrading works including strengthening. Each assessment exercise comprised three separate components: (1) a strain and acceleration monitoring exercise lasting approximately one month; (2) a full-scale dynamic test carried out in a single day without closing the bridge; and (3) a finite-element model updating exercise to identify structural parameters and mechanisms. This paper presents the dynamic testing and the modal analysis used to identify the vibration properties and the quantification of the effectiveness of the upgrading through the subsequent model updating. Before and after upgrade, similar sets of vibration modes were identified, resembling those of an orthotropic plate with relatively weak transverse bending stiffness. Conversion of bearings from nominal simple supports to nominal full fixity was shown via model updating to be the principal cause of natural frequency increases of up to 50%. The utility of the combined experimental and analytical process in direct identification of structural properties has been proven, and the procedure can be applied to other structures and their capacity assessments.