全文获取类型
收费全文 | 4150篇 |
免费 | 553篇 |
国内免费 | 433篇 |
专业分类
电工技术 | 50篇 |
综合类 | 293篇 |
化学工业 | 643篇 |
金属工艺 | 1144篇 |
机械仪表 | 160篇 |
建筑科学 | 537篇 |
矿业工程 | 391篇 |
能源动力 | 35篇 |
轻工业 | 168篇 |
水利工程 | 139篇 |
石油天然气 | 308篇 |
武器工业 | 42篇 |
无线电 | 127篇 |
一般工业技术 | 618篇 |
冶金工业 | 391篇 |
原子能技术 | 42篇 |
自动化技术 | 48篇 |
出版年
2024年 | 20篇 |
2023年 | 66篇 |
2022年 | 188篇 |
2021年 | 212篇 |
2020年 | 217篇 |
2019年 | 155篇 |
2018年 | 114篇 |
2017年 | 168篇 |
2016年 | 200篇 |
2015年 | 197篇 |
2014年 | 229篇 |
2013年 | 267篇 |
2012年 | 333篇 |
2011年 | 326篇 |
2010年 | 244篇 |
2009年 | 277篇 |
2008年 | 216篇 |
2007年 | 314篇 |
2006年 | 269篇 |
2005年 | 236篇 |
2004年 | 216篇 |
2003年 | 142篇 |
2002年 | 83篇 |
2001年 | 65篇 |
2000年 | 55篇 |
1999年 | 54篇 |
1998年 | 46篇 |
1997年 | 32篇 |
1996年 | 35篇 |
1995年 | 40篇 |
1994年 | 37篇 |
1993年 | 20篇 |
1992年 | 11篇 |
1991年 | 9篇 |
1990年 | 19篇 |
1989年 | 4篇 |
1988年 | 5篇 |
1987年 | 2篇 |
1986年 | 1篇 |
1984年 | 1篇 |
1983年 | 1篇 |
1980年 | 2篇 |
1979年 | 4篇 |
1975年 | 1篇 |
1951年 | 3篇 |
排序方式: 共有5136条查询结果,搜索用时 281 毫秒
1.
Yajing Qi Yuying Yang Alkassoumi Hassane Hamadou Qiuyun Shen Bin Xu 《International Journal of Food Science & Technology》2022,57(4):2104-2112
Wheat bran is rich in functional ingredients, but the high level of lipase limits its applications. Tempering–preservation treatment (at 70–90 °C with moisture of 20%–40% for 1–4 h) was exploited for stabilising wheat bran and its effect on polyphenols was investigated. The results showed that more lipase was inactivated at higher tempering moisture, temperature and longer time. The optimum condition for inactivation of wheat bran lipase was 30% moisture and 90 °C for 4 h. The inactivation rate reached 93.8% with a residual enzyme activity of 0.264 U g−1. Under the optimum condition, the sum of free phenolic acids rose from 25.4 to 55.8 µg g−1. As for bound phenolic acids, there was a slight increase of hydroxybenzoic acid derivatives but a slight decrease of hydroxycinnamic acid derivatives. The total contents of phenolic acids before and after stabilisation were not significantly different. This study showed the possibility of using tempering–preservation as an efficient method for inactivation of wheat bran lipase while maintaining its phenolic compounds, which could be used in the production of whole wheat flour. 相似文献
2.
3.
提供了一种简便易行的靶面激光光斑尺寸原位测量的方法。从高斯光束的横向光强分布特性出发,建立了激光烧蚀斑半径与辐照激光能量、光斑尺寸、烧蚀阈值间的关系式,模拟分析发现辐照激光光斑尺寸对烧蚀斑半径随辐照能量变化曲线有较大影响。对于脉宽为2 ms,波长为1064 nm的激光,实验测量了不同能量激光辐照下相纸烧蚀斑半径,并用推导出的关系式拟合测量数据,获得了靶面处光斑尺寸和样品烧蚀阈值。同时,也测量了不同位置处的光斑尺寸和样品烧蚀阈值,对高斯光束束腰位置和样品烧蚀阈值的光斑尺寸效应进行了验证。研究结果表明该技术结果可靠,简单高效。该技术可以为高能激光与固体物质相互作用的基础研究和激光加工等应用领域中实现简单方便地测量靶面光斑尺寸提供帮助。 相似文献
4.
为了减小传统的最差情况设计方法引入的电压裕量,提出了一种变化可知的自适应电压缩减(AVS)技术,通过调整电源电压来降低电路功耗.自适应电压缩减技术基于检测关键路径的延时变化,基于此设计了一款预错误原位延时检测电路,可以检测关键路径延时并输出预错误信号,进而控制单元可根据反馈回的预错误信号的个数调整系统电压.本芯片采用SMIC180 nm工艺设计验证,仿真分析表明,采用自适应电压缩减技术后,4个目标验证电路分别节省功耗12.4%,11.3%,10.4%和11.6%. 相似文献
5.
中国深层煤层气资源丰富,但总体勘探和认识程度较低,尚未形成较为系统的深层煤层气地质理论。通过解剖分析准噶尔盆地白家海凸起和鄂尔多斯盆地临兴区块深层"超饱和"煤层气井的试气/生产动态,估算原地游离气的含气量,分析了深层"超饱和"煤层气的形成条件。研究表明:①深层"超饱和"煤层气储层中除吸附气外,还含有原地游离气,用常规试气方法可直接获得气流,煤层气的产出不明显依赖于排水降压;②埋藏超过一定深度,在煤阶和温度的综合作用下,煤的吸附能力将随埋深的继续增加而降低,煤层中吸附气的饱和度有增加的趋势,在达到吸附饱和后,出现原地游离气并形成"超饱和"煤层气,盆地深层具有"超饱和"煤层气形成的优势条件;③由于地温梯度和压力梯度的不同,不同盆地"超饱和"煤层气出现的临界深度不同,异常高压和异常高热流可以降低深层"超饱和"煤层气形成的临界深度;④深层"超饱和"煤层气开发具有大大缩短见气时间、充分利用地层能量和累积产水量低等优势,有望成为未来煤层气勘探开发的一个重要领域。 相似文献
6.
低温低渗透砂岩油藏窜流大孔道深部封堵技术研究 总被引:4,自引:0,他引:4
所用堵剂为高强度的淀粉接枝聚丙烯酰胺交联凝胶SAMG-1,由<6%淀粉、4.5%-5.5%丙烯酰胺、0.003%-0.006%交联剂组成,35℃成胶时间受淀粉和交联剂用量控制,为18-20小时以上,成胶前黏度-100 mPa.s。该堵剂具有长期稳定性,在储层岩心中注入深度15 cm的堵剂,在35℃候凝48小时后及老化90天后,封堵强度分别为0.61和0.59 MPa/cm,封堵率分别为98.6%和98.1%。该堵剂优先进入高渗层,注入0.5 PV并成胶后,2组双填砂管组成的模型低、高渗管渗透率保留率分别为68.4%、0.7%和69.4%、0.0%。吉林扶余油田西一区+15-8.2区块有水井6口,油井13口,含水率达91.5%,注入水最快在5天内到达油井。报道了该区块整体深部调剖封堵窜流通道的情况,详细叙述了+15-9.2井施工中通过注入压力和井底回压控制注入流量,使堵剂陆续进入原生和次生孔道的工艺作业,该井设计注入堵剂92 m3。6口水井整体调剖后,油井产液量差别减小,产油量增加,有效期已超过了9个月,共增油843 t,含水平均下降3.87%。图7表1参8。 相似文献
7.
根据石油开采业对石油机械产品的需求 ,利用机械理论基础知识 ,通过实践设计 ,提出了对几何尺寸长的金属管类进行调质处理后的均匀冷却方法 ,以满足其性能要求。 相似文献
8.
9.
PENGLiming MAOXiemin XUKuangdi DINGWenjiang 《稀有金属(英文版)》2002,21(1):62-66
In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed. 相似文献
10.