Machine fault diagnosis with small sample based on variational information constrained generative adversarial network

In actual engineering scenarios, limited fault data leads to insufficient model training and over-fitting, which negatively affects the diagnostic performance of intelligent diagnostic models. To solve the problem, this paper proposes a variational information constrained generative adversarial network (VICGAN) for effective machine fault diagnosis. Firstly, by incorporating the encoder into the discriminator to map the deep features, an improved generative adversarial network with stronger data synthesis capability is established. Secondly, to promote the stable training of the model and guarantee better convergence, a variational information constraint technique is utilized, which constrains the input signals and deep features of the discriminator using the information bottleneck method. In addition, a representation matching module is added to impose restrictions on the generator, avoiding the mode collapse problem and boosting the sample diversity. Two rolling bearing datasets are utilized to verify the effectiveness and stability of the presented network, which demonstrates that the presented network has an admirable ability in processing fault diagnosis with few samples, and performs better than state-of-the-art approaches.     

Adaptive robust boundary control of shaft vibrations under perturbations with unknown upper bounds

This paper presents robust and adaptive boundary control designs to stabilize the two‐dimensional vibration of hybrid shaft model. The hybrid shaft is mathematically represented by a set of partial differential equations, governing the shaft vibrations, coupled to ordinary differential equations, describing rigid body spinning and dynamic boundary conditions. The control objective is to stabilize the transverse vibrations of the perturbed shaft while regulating the spinning rate. To achieve this, the paper first establishes robust boundary control laws that fulfil the control objective in the presence of modeling uncertainties and external disturbances operating over the shaft domain and boundary. Lyapunov‐based analyses show that the proposed robust control exponentially stabilizes the shaft with vanishing distributive perturbations, while assuring ultimately bounded vibrations in the case of nonvanishing perturbations. Then, adaptive control philosophy is utilized to achieve redesigned robust controllers that only use online adaptation of control gains without acquiring the knowledge of bounds on perturbations, as well as dynamic parameters. An advantage of this design is avoiding an overconservative robust control law, which may induce poor stability and chattering in tackling system perturbations with unknown upper bounds. Simulations through finite element method illustrate the results. Copyright © 2014 John Wiley & Sons, Ltd.     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

上保护层开采底板破坏深度和应力分析研究

上保护层开采导致的底板变形、应力释放会使被保护层内高瓦斯沿着上覆岩层内形成的空隙裂隙结构向上运移，很容易造成所采工作面采空区内瓦斯增加，造成工作面瓦斯超限。以峰峰集团以黄沙矿为研究实例，针对其主采的2号煤层利用FLAC^3D模拟软件进行上保护层开采底板应力研究，揭示了上保护层开采底板应力的规律特性，对于保护层开采工作瓦斯治理具有一定的指导意义。     

基于滑模的运载器主动段俯仰通道姿控系统设计

与传统比例-积分-微分（PID）控制方法相比，滑模控制（SMC）方法可以比较容易地将不确定性纳入控制器设计中，从而增强系统的鲁棒性。探索了SMC技术在运载器主动段姿态控制中的工程应用，首先通过分析基于趋近律的SMC系统，提出了降低不连续切换项系数的需求，然后研究了基于干扰上界的SMC方法。三通道小偏差仿真结果验证了两种方法的控制效果，表明第2种控制器的鲁棒性更好，稳态误差小，同时发动机喷管摆角需求较小。     

气管上段腺样囊性癌的临床病理

目的　探讨气管上段腺样囊性癌的临床病理特征及诊断和鉴别诊断要点。方法　收集2000年1月至2014年2月在北京协和医院确诊的4例气管上段腺样囊性癌病例，通过光镜、免疫组织化学及组织化学染色分析其临床病理特征、免疫组织化学特点、诊断及鉴别诊断要点。结果　4例气管上段腺样囊性癌患者中，男1例，女3例，平均年龄47岁(38~57岁）；既往均无腺样囊性癌病史，1例患者既往有结节性甲状腺肿手术史。镜下检查4例均为筛状/管状型腺样囊性癌，3例累及甲状腺组织，3例累及神经组织，未见淋巴结受累。免疫组织化学染色示4例P16、CD117、BCL2、P63、SMA均阳性，Ki67指数平均8%，TTF1和P53均阴性；4例中基底膜样物胶原Ⅳ阳性；组织化学染色示AB/PAS阳性。术后均接受总剂量为48~56 Gy的放疗，随访6~120个月，平均72.5个月，1例术后96个月复发，3例随访期间无复发及转移。结论　气管上段腺样囊性癌是罕见的原发于气管的低度恶性肿瘤，肿瘤生长缓慢，就诊时多数已侵及甲状腺组织，需要与原发于甲状腺的恶性肿瘤相鉴别，特别是在甲状腺穿刺及术中冰冻检查时。结合电子喉气管镜下表现、典型的形态学及免疫组织化学和组织化学染色有助于准确诊断。手术难以切除干净，术后放疗对延缓疾病复发有一定帮助。     

上水口环形吹氩对中间包内渣眼形成的影响

 中间包上水口环形吹氩可以在塞棒周围形成清洗钢液的环形气幕，同时部分氩气泡随钢液进入上水口内，可以减少非金属夹杂物在水口内壁的黏附，起到防止水口堵塞的作用。然而，不合理的吹氩量会导致中间包内液面渣层受过强的气液羽流冲击而形成渣眼，使得钢液裸露并发生二次氧化，严重影响铸坯质量。采用标准 k ε 湍流模型研究中间包内流体流动，采用DPM模型和VOF模型耦合方法，研究上水口环形吹氩条件下渣眼的形成及演化规律。结果表明，上水口环形吹氩在塞棒周围形成较强的上升流，塞棒上部邻近区域存在多个涡流区；在钢液涡流的影响下，中间包液渣下层远离塞棒区域，上层向塞棒区域迁移；随着吹氩量的增大，平均湍动能增大，塞棒附近钢液速度逐渐增大，钢渣界面钢液速度先增大后减小，渣眼边缘钢液速度先增大后减小然后再增大，速度与垂直方向夹角逐渐减小；增大吹氩量，中间包熔池液面形成以塞棒为中心的渣眼，渣眼面积逐渐增大。试验条件下不产生渣眼的临界吹氩量为4.2 L/min，对应的钢渣界面最大速度为0.247 m/s，与垂直方向夹角为70°。     

强化研磨加工中喷射角度对GCr15轴承钢板塑性变形的影响

利用ABAQUS有限元仿真软件研究不同喷射角度强化研磨加工GCr15轴承钢板过程的塑性变形,得到不同喷射角度与等效塑性应变沿真实路径距离的关系,并通过拉伸试验进行验证。喷射角度为90°的强化研磨加工伸长率为1.4%,相比未经过强化研磨加工的伸长率数值缩减了2.0%。断口收缩率由空白组的4.9%降低到喷射角为90°的2.2%。结合仿真和试验可知,强化研磨加工中喷射角度越大,塑性变形能力越低,材料加工越难。     

Methodology for optimization of pouring variables using bottom pour for low masses of SS304 (<300 kg) in investment casting process (case study)

Bottom pour ladles with stopper rod systems are commonly used in the metal casting industry. However, stopper rod bottom-pouring systems have not yet been developed for the lower thermal masses of alloys typically used in the investment casting industry. Large thermal masses used with bottom pour systems are typically limited for ladles larger than 700 kg and to certain alloys with higher fluidity and longer solidification time like cast iron, aluminum alloys etc. In this study, bottom pour ladle designs and low thermal mass refractory systems have been developed and evaluated in production investment foundry trials with 300 kg pouring ladle. The ladles system and pouring practices used will be described along with the results from the pouring trials for SS304 that represents typical alloys used in Investment casting industries. Optimization of the variables used in an experimentation using Genetic algorithm is also explained.     

狭缝节流空气静压轴承局部气膜流场的直接数值模拟

采用3阶精度的迎风格式及2阶精度的中心差分格式,直接求解二维非定常N-S方程组,研究狭缝节流空气静压轴承压降恢复之后区域的流场特性。使用雷诺方程计算相同位置气膜中心处的流场状态,并与直接数值模拟方法的计算结果进行对比。结果表明:雷诺方程与N-S方程在计算域内计算结果基本一致,两者压力偏差为0.173%,速度偏差为1.217%;流场压力、密度沿气流方向逐渐减小,但在气膜方向几乎不变;流场速度、压力梯度沿气流方向逐渐增加,速度在流场出口处达到最大值;直接数值模拟方法得到了流场的温度变化,即整个流场的温度变化很小,温度整体呈上下高、中心低的分布,而雷诺方程无法计算得出整个流场的温度变化情况;采用雷诺方程计算轴承压降恢复之后区域的流场是合理的。