Laboratory Studies to Determine Suitable Chemicals to Improve Oil Recovery from Garzan Oil Field

Garzan oil field is located at the south east of Turkey. It is a mature oil field and the reservoir is fractured carbonate reservoir. After producing about 1% original oil in place (OOIP) reservoir pressure started to decline. Waterflooding was started in order to support reservoir pressure and also to enhance oil production in 1960. Waterflooding improved the oil recovery but after years of flooding water breakthrough at the production wells was observed. This increased the water/oil ratio at the production wells. In order to enhance oil recovery again different techniques were investigated. Chemical enhanced oil recovery (EOR) methods are gaining attention all over the world for oil recovery. Surfactant injection is an effective way for interfacial tension (IFT) reduction and wettability reversal. In this study, 31 different types of chemicals were studied to specify the effects on oil production. This paper presents solubility of surfactants in brine, IFT and contact angle measurements, imbibition tests, and lastly core flooding experiments. Most of the chemicals were incompatible with Garzan formation water, which has high divalent ion concentration. In this case, the usage of 2-propanol as co-surfactant yielded successful results for stability of the selected chemical solutions. The results of the wettability test indicated that both tested cationic and anionic surfactants altered the wettability of the carbonate rock from oil-wet to intermediate-wet. The maximum oil recovery by imbibition test was reached when core was exposed 1-ethly ionic liquid after imbibition in formation water. Also, after core flooding test, it is concluded that considerable amount of oil can be recovered from Garzan reservoir by waterflooding alone if adverse effects of natural fractures could be eliminated.     

Microstructure,wear and corrosion characteristics of multiple-reinforced (SiC–B4C–Al2O3) Al matrix composites produced by liquid metal infiltration

In this study, AA7075 aluminum matrix composites reinforced with the combination of SiC, Al₂O₃, and B₄C particles were fabricated by the liquid metal infiltration method. The effects of the relative ratio of B₄C and Al₂O₃ particles on the microstructural, wear, and corrosion features of the composite samples were analyzed using XRD, light metal microscopy, SEM, EDS, Brinell hardness, ball-on-disc type tribometer, and potentiodynamic polarization devices. It was determined that infiltration occurred more successfully, and homogenously distributed particles with reduced porosity were obtained as the amount of Al₂O₃ increased. Worn surface studies revealed that the specimens were predominantly worn by abrasion and adhesion. The increase in B₄C/Al₂O₃ ratio caused a decrease in the hardness and wear strength, whereas it increased the corrosion resistance.     

Compressive strength and wear properties of SiC/Al6061 composites reinforced with high contents of SiC fabricated by pressure-assisted infiltration

Pressure-assisted infiltration was used to synthesize SiC/Al 6061 composites containing high weight percentages of SiC. A combination of PEG and glass water was used to fabricate SiC preforms and the effect of the presence of glass water on the microstructure and mechanical properties of the preforms was evaluated by performing compression tests on the preforms. Also, the compressive strength and the hardness of the SiC/Al composites were investigated. The results revealed that the glass water improved the compressive strength of the preforms by about five times. The microstructural characterization of the composites showed that the penetration of the aluminum melt into the preforms was completed and almost no porosity could be seen in the microstructures of the composites. Moreover, the composite containing 75 wt% SiC exhibited the highest compressive strength as well as the maximum hardness. The results of the wear tests showed that increasing the SiC content reduces the wear rate so that the Al-75 wt% SiC composite has a lower wear rate and a lower coefficient of friction than those of Al-67 wt% SiC composite. This indicated higher wear resistance in these composites than the Al alloy due to the formation of a tribological layer on the surface of the composites.     

不同管距时玉米渗灌效果的试验研究

在运城市夹马口灌区和红旗灌区进行了1996,1997两个年度的玉米渗灌试验,研究了不同毛管间距条件下渗灌对其产量及水分生产率等的影响。结果表明,玉米渗灌毛管间距采用0.8~1.0 m较为适宜。毛管间距愈大,产量愈低;渗灌较地面灌平均减产7.23%,较旱地平均增产30.8%;玉米生长期内总耗水量地面灌最大,渗灌次之,旱地最小。渗灌可明显提高玉米水分生产率,渗灌处理水分生产率平均为1.65 kg/m3,是地面灌的1.2倍,是旱地的1.33倍;两年度渗灌较地面灌平均节水44.4%。     

构皮滩水电站泄洪洞优化设计

构皮滩水电站为满足2008年12月工程提前发电的需要,结合现有泄洪洞地质情况和施工情况对泄洪洞布置进行了专题研究,结果表明利用降低进口高程为550 m的泄洪洞和坝身放空底孔联合参与后期导流,可缓解2007年导流隧洞下闸封堵后大坝在2008年汛期施工的压力,为大坝施工增加了2个月左右的工期。     

辽河防洪应急工程中的加筋粉细砂筑坝技术

加筋粉细砂筑坝是一门新兴技术,通过在辽河防洪应急工程右岸李家堡段应用表明,该项技术在技术上是可行的、在经济上是合理的。本文介绍了该技术在辽河防洪应急工程右岸李家堡段的应用。     

利用黄河泥沙加固下游大堤

黄河是一条举世闻名的多泥沙河流，善淤、善决、善徒给沿河人民带来对过深重灾难，防洪问题一直是国家的心腹之患。泥沙问题是黄河防洪问题的症结所在。在总结固大堤经验的基础，进行挖河疏浚，淤筑“相对地下河”，已作为黄河治理的一项重大决策付诸实施。     

三峡水库减淤增容调度方式研究——多汛限水位调度方案

本文建议在汛期中小流量时（Q<35000m3/s），将坝前水位维持在148～151m；出现汛情且流量更较大后，将坝前水位降低到143m；入库流量大于35000m3/s且短期预报将出现大于十年一遇洪水时，预泄洪水到135m.按这一调度，汛期约80％时间可以维持在较高水位，一般洪水期。汛限水位143m不影响坝区通航，135m水位迎洪可大量增加防洪库客。到100年后可减淤30亿m3，增加防洪库容约40亿m3.变动回水区减淤40%，优化了坝区水沙搭配，可改善通航条件。降低库区洪水位，缓解防洪与移民的矛盾。可对发电带来较大好处：提高发电效益，减少粗沙过机。初期水库排沙比大于原方案，可减轻下游冲刷。同时，可减小三峡汛初泄水与鄱阳湖防洪的矛盾。     

长江螺山站高水位流量关系和城陵矶（莲花塘）控制水位的研究

螺山站高水位流量关系是确定长江城陵矶（莲花糖）控制水位的基本依据，从基本的河道水力学规律出发，考虑涨落率修正、瞬时比降修正，计算各时段点的代表性比降，和相应糙率，求出均值，根据断面资料，得出高水位的稳定流曲线，并以各日流量转化的稳定流点，进行验证，精度很好，分析了河段区间流量对螺山站稳定流量的影响。阐明了螺山站稳定流量的变化情况和趋势，推求了各次大洪水的超额洪量，计算出莲花糖以上的总入流，根据现今的湖区及槽蓄容积进行洪水演进，计算1954年特大洪水的超额洪量，并分析节三峡水库拦洪后对长江中下游超额水量的影响；对莲花塘不同防洪控制水位进行了技术经济分析和评价，提出了抬高控制水位的具体建议。