Fabrication of alumina ceramics with functional gradient structures by digital light processing 3D printing technology

Alumina ceramics with different unit numbers and gradient modes were prepared by digital light processing (DLP) 3D printing technology. The side length of each functional gradient structure was 10 mm, the porosity ratio was controlled to 70%, and the number of units were (1 × 1 × 1 unit) and (2 × 2 × 2 unit) respectively. The different gradient modes were named FCC, GFCC-1, GFCC-2 and GFCC-3. SEM, XRD, and other characterization methods proved that these gradient structures of alumina ceramics had only α-Al2O3 phase and good surface morphology. The mechanical properties and energy absorption properties of alumina ceramics with different functional gradient structures were studied by compression test. The results show that the gradient structure with 1 × 1 × 1 unit has better mechanical properties and energy absorption properties when the number of units is different. When the number of units is the same, GFCC-2 and GFCC-3 gradient structures have better compressive performance and energy absorption potential than FCC structures. The GFCC-2 gradient structure with 1 × 1 × 1 unit has a maximum compressive strength of 19.62 MPa and a maximum energy absorption value of 2.72 × 105 J/m3. The good performance of such functional gradient structures can provide new ideas for the design of lightweight and compressive energy absorption structures in the future.     

Hydraulic reactivity and cement formation of baghdadite

In this study, the hydraulic reactivity and cement formation of baghdadite (Ca₃ZrSi₂O₉) was investigated. The material was synthesized by sintering a mixture of CaCO₃, SiO₂, and ZrO₂ and then mechanically activated using a planetary mill. This leads to a decrease in particle and crystallite size and a partial amorphization of baghdadite as shown by X-ray powder diffraction (XRD) and laser diffraction measurements. Baghdadite cements were formed by the addition of water at a powder to liquid ratio of 2.0 g/ml. Maximum compressive strengths were found to be ~2 MPa after 3-day setting for a 24-h ground material. Inductively coupled plasma mass spectrometry (ICP-MS) measurements showed an incongruent dissolution profile of set cements with a preferred dissolution of calcium and only marginal release of zirconium ions. Cement formation occurs under alkaline conditions, whereas the unground raw powder leads to a pH of 11.9 during setting, while prolonged grinding increased pH values to approximately 12.3.     

基于梯度提升决策树的车轮轮缘厚度磨耗预测

轮对在列车走行过程中起着导向、承受以及传递载荷的作用，其踏面及轮缘磨耗对地铁列车运行安全性和钢轨的寿命都将产生重要影响。根据地铁列车车轮磨耗机理，分析车轮尺寸数据特点，针对轮缘厚度这一型面参数，基于梯度提升决策树算法构建轮缘厚度磨耗预测模型。在该模型的基础上，任意选取某轮对数据进行验证分析，结果表明：基于梯度提升决策树的轮对磨耗预测模型具有较好的预测精度，可预测出1~6个月的轮缘厚度变化趋势范围，预测时间范围较长，可为地铁维保部门对轮对的维修方式由状态修转为预防修提供指导性建议。     

极限工况下的管网“互联互通”改进方案

在全国天然气管道“主干互联、区域成网”(以下简称“互联互通”)基础格局逐渐形成的背景下,天然气管网规模日益扩大、管道分支和气源增加,并且分布不集中、输送方向可变,使得输气方案更加灵活,可以更好地解决某些地域的供气紧张问题;但受现有站场和设备的限制,暂不能满足某些多线组合极限工况,使得“互联互通”的初衷难以全部实现。为了使得现有的各输气干线在实现“互联互通”之后可以满足更多的多线组合工况,在分析“互联互通”背景下M管网工况变化的基础上,研发了可以进行水力仿真和压气站方案制订的计算软件,并对3种极限工况下的不同输气量情况进行了可行性试算,进而基于试算结果提出了相应的管网改进建议。研究结果表明:(1)经验证,软件计算误差满足要求;(2)在M管道某处增设压气站或在某些输气站场配置压缩机组;(3) M管网改进调整后,可以完成大部分的多线组合极限工况,真正实现“互联互通”的输气方案。结论认为,该研究成果有助于推进全国天然气管网早日实现“互联互通”。     

Evolving an Accurate Decision Tree-Based Model for Predicting Carbon Dioxide Solubility in Polymers

Solubility is one of the most indispensable physicochemical properties determining the compatibility of components of a blending system. Research has been focused on the solubility of carbon dioxide in polymers as a significant application of green chemistry. To replace costly and time-consuming experiments, a novel solubility prediction model based on a decision tree, called the stochastic gradient boosting algorithm, was proposed to predict CO₂ solubility in 13 different polymers, based on 515 published experimental data lines. The results indicate that the proposed ensemble model is an effective method for predicting the CO₂ solubility in various polymers, with highly satisfactory performance and high efficiency. It produces more accurate outputs than other methods such as machine learning schemes and an equation of state approach.     

Gradient-based recursive parameter estimation for a periodically nonuniformly sampled-data Hammerstein–Wiener system based on the key-term separation

The identification of the Hammerstein–Wiener (H-W) systems based on the nonuniform input–output dataset remains a challenging problem. This article studies the identification problem of a periodically nonuniformly sampled-data H-W system. In addition, the product terms of the parameters in the H-W system are inevitable. In order to solve the problem, the key-term separation is applied and two algorithms are proposed. One is the key-term-based forgetting factor stochastic gradient (KT-FFSG) algorithm based on the gradient search. The other is the key-term-based hierarchical forgetting factor stochastic gradient (KT-HFFSG) algorithm. Compared with the KT-FFSG algorithm, the KT-HFFSG algorithm gives more accurate estimates. The simulation results indicate that the proposed algorithms are effective.     

一种基于小字典不对等语料的跨语言词嵌入方法

双语词嵌入通常采用从源语言空间到目标语言空间映射,通过源语言映射嵌入到目标语言空间的最小距离线性变换实现跨语言词嵌入。然而大型的平行语料难以获得,词嵌入的准确率难以提高。针对语料数量不对等、双语语料稀缺情况下的跨语言词嵌入问题,该文提出一种基于小字典不对等语料的跨语言词嵌入方法,首先对单语词向量进行归一化,对小字典词对正交最优线性变换求得梯度下降初始值,然后通过对大型源语言(英语)语料进行聚类,借助小字典找到与每一聚类簇相对应的源语言词,取聚类得到的每一簇词向量均值和源语言与目标语言对应的词向量均值,建立新的双语词向量对应关系,将新建立的双语词向量扩展到小字典中,使得小字典得以泛化和扩展。最后,利用泛化扩展后的字典对跨语言词嵌入映射模型进行梯度下降求得最优值。在英语—意大利语、德语和芬兰语上进行了实验验证,实验结果证明该文方法可以在跨语言词嵌入中减少梯度下降迭代次数,减少训练时间,同时在跨语言词嵌入上表现出较好的正确率。     

Design and Fabrication of Concentration‐Gradient Generators with Two and Three Inlets in Microfluidic Chips

A simple and low‐cost method for designing and fabricating concentration‐gradient generators with two and three inlets is proposed which can generate different concentration gradients at varying flow velocities. The microchannel structure was designed in S‐shape and left‐right symmetry. The concentration‐gradient generator was simulated based on the finite element method. The microchannels were processed on a computer numerical control (CNC) engraving and milling machine on poly(methylmethacrylate) substrate, and then two concentration‐gradient generators were fabricated by hot bonding technology. The results of experiment and simulation were compared to prove the feasibility of the method. Flow velocity was an important factor for generating different concentration gradients. The concentration‐gradient profiles of the generators with two and three inlets present approximately linear and quadratic curves.     

构皮滩水电站泄洪洞优化设计

构皮滩水电站为满足2008年12月工程提前发电的需要,结合现有泄洪洞地质情况和施工情况对泄洪洞布置进行了专题研究,结果表明利用降低进口高程为550 m的泄洪洞和坝身放空底孔联合参与后期导流,可缓解2007年导流隧洞下闸封堵后大坝在2008年汛期施工的压力,为大坝施工增加了2个月左右的工期。     

PETROLEUM POTENTIAL, THERMAL MATURITY AND THE OIL WINDOW OF OIL SHALES AND COALS IN CENOZOIC RIFT BASINS, CENTRAL AND NORTHERN THAILAND

Oil shales and coals occur in Cenozoic rift basins in central and northern Thailand. Thermally immature outcrops of these rocks may constitute analogues for source rocks which have generated oil in several of these rift basins. A total of 56 oil shale and coal samples were collected from eight different basins and analysed in detail in this study. The samples were analysed for their content of total organic carbon (TOC) and elemental composition. Source rock quality was determined by Rock‐Eval pyrolysis. Reflected light microscopy was used to analyse the organic matter (maceral) composition of the rocks, and the thermal maturity was determined by vitrinite reflectance (VR) measurements. In addition to the 56 samples, VR measurements were carried out in three wells from two oil‐producing basins and VR gradients were constructed. Rock‐Eval screening data from one of the wells is also presented. The oil shales were deposited in freshwater (to brackish) lakes with a high preservation potential (TOC contents up to 44.18 wt%). They contain abundant lamalginite and principally algal‐derived fluorescing amorphous organic matter followed by liptodetrinite and telalginite (Botryococcus‐type). Huminite may be present in subordinate amounts. The coals are completely dominated by huminite and were formed in freshwater mires. VR values from 0.38 to 0.47%R_o show that the exposed coals are thermally immature. VR values from the associated oil shales are suppressed by 0.11 to 0.28%R_o. The oil shales have H/C ratios >1.43, and Hydrogen Index (HI) values are generally >400 mg HC/g TOC and may reach 704 mg HC/ gTOC. In general, the coals have H/C ratios between about 0.80 and 0.90, and the HI values vary considerably from approximately 50 to 300 mg HC/gTOC. The HI_max of the coals, which represent the true source rock potential, range from ～160 to 310 mg HC/g TOC indicating a potential for oil/gas and oil generation. The steep VR curves from the oil‐producing basins reflect high geothermal gradients of ～62°C/km and ～92°C/km. The depth to the top oil window for the oil shales at a VR of ～0.70%R_o is determined to be between ～1100 m and 1800 m depending on the geothermal gradient. The kerogen composition of the oil shales and the high geothermal gradients result in narrow oil windows, possibly spanning only ～300 to 400 m in the warmest basins. The effective oil window of the coals is estimated to start from ～0.82 to 0.98%R_o and burial depths of ～1300 to 1400 m (～92°C/km) and ～2100 to 2300 m (～62°C/km) are necessary for efficient oil expulsion to occur.