Evaluation of cut cell cartesian method for simulation of a hook and claw type hydrogen pump

Hook and claw pumps are used for recirculation of excess hydrogen in fuel cells. Optimization of the pump design is essential. Computational Fluid Dynamic (CFD) is an effective method for performance optimization. However, it is difficult to conduct CFD simulation because of the sharp cusp of the rotor profile. Cut cell Cartesian mesh could be the solution to handle this complex and moving geometries. The aim of this paper is to evaluate ANSYS Forte for hook and claw pumps. Firstly, the conservation accuracy of the cut cell cartesian mesh is verified using an adiabatic piston cylinder case. Then, simulation results of hook and claw type pump are compared with experimental data. Finally, simulation results of air and hydrogen are compared. The results show that the CFD simulation of hook and claw pumps using cut cell cartesian mesh could provide an efficient and effective approach for the optimization of the system.     

Formation process of zirconia nanotubes and porous structures and model of oxygen bubble growth

Preparation and growth mechanism of anodization of Ti and Al has been widely concerned for two decades, but the research on anodic ZrO₂ is relatively lacking. In this paper, anodic TiO₂ and ZrO₂ nanotubes were prepared in glycerol electrolyte containing 0.35 M NH₄F and 4 vol% H₂O under different anodizing voltages. We had successfully prepared the anodic ZrO₂ nanotubes (AZNTs) with a complete top and a “bulb” at the bottom under 60 V, and with the increase of the applied anodizing voltage, the “bulb” cavity also increased. However, under the same anodizing conditions, the surface of anodic TiO₂ nanotubes (ATNTs) is a cluster of nano-tip morphology, and the bottom of the ATNTs is a conventional hemisphere shape. In addition, both AZNTs and porous anodic zirconia (PAZ) were found to coexist in the anodic ZrO₂ layer prepared at 60 V. Here, we used the oxygen bubble model and ionic current and electronic current theories to analyze the reason of the special morphology. It is confirmed that the porous anodic oxides are actually evolved from nanotubes. In other words, the structure is essentially the same.     

Theoretical study of a thermoelectric-assisted vapor compression cycle for air-source heat pump applications

This paper proposes a thermoelectric-assisted vapor compression cycle (TVCC) for applications in air-source heat pump systems which could enhance the heating capacity of the system. Performances of TVCC are calculated and then compared with that of basic vapor compression cycle (BVCC). The simulation results show that when coefficients of performance (COPs) of the two cycles are almost equal, the TVCC under maximum COP condition of the thermoelectric modules still performs better than BVCC by 13.0% in heating capacity through selecting the appropriate intermediate temperature. In addition, the TVCC can also achieve an improvement of 16.4%–21.7% in both the heating COP and capacity when compared with the BVCC with an assistant electric heater that is provided with the equivalent power input of thermoelectric heat exchanger. Thus, the TVCC could be beneficial to the applications in small heat pumps if there is always need for auxiliary electric heat.     

燃气热水器在无回水管水路中实现零冷水的方案研究

本文分析了燃气热水器行业针对无回水管水路系统实现零冷水功能的现有技术方案,指出现有技术方案存在的一些缺陷,并结合试验研究,对无回水管水路系统提出了一套全新的实现零冷水功能的技术解决方案。     

抽油井不压井作业装置及抽油泵底阀设计

江苏油田的部分油井存在油管短路、地层高压低渗、漏失严重等问题,这些问题造成压井作业困难,并且压井作业过程中的井控与环境污染风险较大。为了进行不压井检泵作业,同时缩短检泵之后的产量恢复周期,进行了不压井作业技术研究,并研制了不压井作业装置。为解决起下抽油杆过程中的防喷问题,改进了抽油泵底阀结构,该结构可实现起下抽油杆过程中油管不带压、无溢流,并保障起下油管过程中的井控安全。该技术在江苏油田现场应用9井次,效果良好。     

宁夏宁东供水工程主机设备形式参数选择与国际招标

宁东供水工程供水水泵共有卧式和立式离心泵2种方案可供选择,也是工程论证时争论的焦点,经综合比较及主机设备的国际招标,最终确定了奥地利安德里兹公司的卧式双吸中开式离心泵为宁东供水工程的供水水泵。     

复合材料一体化钻井泵缸套产业化技术研究

介绍了复合材料一体化钻井泵缸套在产业化过程中的若干关键技术。通过对缸套内套材料成分和组织的优化研究,双液分时离心浇注工艺优化研究以及双液离心浇注工装开发,实现了新工艺缸套的产业化。与现行的热镶装双金属缸套工艺相比,采用新技术生产的缸套平均使用寿命超过750h,生产成本下降了20%。     

Nd:YVO4/KTP全固化倍频激光器的研究

介绍了两种腔型结构不同的Nd:YVO4/KTP全固化倍频绿光激光器,对腔结构参数进行了优化计算;在相同的实验条件下,对这两种腔的输出和稳定性等特性进行了比较和深入分析,在此基础上得出结论,提出改进措施。该折叠腔方案已进入产品化阶段。     

迷宫螺旋泵和密封工作特性研究

介绍了一种实测迷宫螺旋泵和密封工作特性的实验方法,通过该方法可以测得迷宫螺旋泵的泵送特性曲线、迷宫螺旋端面组合密封的最大密封压力以及端面开启的开始转速,具有一定的实用价值。