Enhanced gaseous hydrogen solubility in ferritic and martensitic steels at low temperatures

Metals that are exposed to high pressure hydrogen gas may undergo detrimental failure by embrittlement. Understanding the mechanisms and driving forces of hydrogen absorption on the surface of metals is crucial for avoiding hydrogen embrittlement. In this study, the effect of stress-enhanced gaseous hydrogen uptake in bulk metals is investigated in detail. For that purpose, a generalized form of Sievert's law is derived from thermodynamic potentials considering the effect of microstructural trapping sites and multiaxial stresses. This new equation is parametrized and verified using experimental data for carbon steels, which were charged under gaseous hydrogen atmosphere at pressures up to 1000 bar. The role of microstructural trapping sites on the parameter identification is critically discussed. Finally, the parametrized equation is applied to calculate the stress-enhanced hydrogen solubility of thin-walled pipelines and thick-walled pressure vessels during service.     

基于特征建模的TDD系统大气波导干扰控制体系研究

大气波导干扰是特定气象条件下发生的时分双工（time-division duplex，TDD）系统内干扰，是TDD移动通信系统大规模组网面临的顽疾。在总结分析大气波导干扰成因和分类等的基础上，对大气波导干扰进行建模和表征，验证了海量干扰源在时域和频域的功率集总特征，并结合大量4G/5G现网实测数据给出了典型条件下内陆波导和海面波导的量化干扰信号传播模型，对于干扰的预测和预防具有重要意义。基于干扰特征，给出了TDD系统预防大气波导干扰的帧结构与组网的4项设计原则，5G现网数据表明干扰控制方案有效，上行干扰下降10 dB以上，相关原则对于6G系统的设计也具有指导意义。     

Interface regulation effects on mechanical behavior of heterostructure Ti6Al4V/TiAl-based laminated composite sheets

Design of architectured composites with layered-ordered structure can solve the strength-toughness mismatch problem of structural materials. In the present study, heterostructure Ti6Al4V/TiAl laminated composite sheets with different thicknesses of interface layer and TiAl composite layer were successfully produced by hot-pressing technology. The effects of interface regulation and laminated structure on their mechanical properties, crack propagation, and fracture behavior were studied. The results indicated that compressive strength of the sheets increased with the decrease in interface thickness. Compressive strength of TiAl composite sheet with thicker composite layer reached 1481.55 MPa at the arrester orientation with sintering holding time of 40 min, which was 25.96% higher than that of the sheet obtained at 120 min. Analysis indicated that the interface area transferred stress through slip bands and through-interface cracks. Compressive strength at the divider orientation reached 1443.06 MPa, which was 45.78% higher than that of the sheet obtained at 120 min. In this case, the interface area transferred stress through slip bands and along-interface cracks. For TiAl composite sheets with thinner composite layer, compressive strength was further improved to 1631.01 MPa and 1594.66 MPa at the arrester and divider orientations with sintering holding time of 40 min, respectively. The ductile metal layer exerted a significant toughening effect. Both interface regulation and laminated structure transformation could enhance the hetero-deformation induced (HDI) strengthening and improve the comprehensive mechanical properties of the composite sheets.     

Stress wave propagation in adhesively bonded functionally graded cylinders: an improved model

This study presents an improved mathematical model to analyse the stress wave propagation in adhesively bonded functionally graded (FG) circular cylinders (butt joint) under an axial impulsive load. The volume fractions of the material constituents in the upper and lower cylinders were functionally tailored through the thickness of each cylinder using a power-law. The effective material properties of both cylinders, which are made of aluminum (Al) and silicon carbide (SiC), at any point were predicted by using the Mori–Tanaka homogenization scheme. In this improved model, the governing equations of the wave propagation include the spatial derivatives of local mechanical properties and were discretized by means of the finite difference method. The influence of these spatial derivatives and the compositional gradient exponent on the displacement and stress distributions of the joint was investigated. The material composition variations of both cylinders affected the displacement and stress fields whereas the compositional gradient exponent had a minor effect. The stress concentrations were alleviated in time, the displacement and stress distributions/variations around/along the upper and lower cylinder-adhesive interfaces were significantly affected by the adhesive layer. The spatial derivatives also affected the temporal histories of the displacement and stress components evaluated at the selected critical points of the upper cylinder, adhesive layer and lower cylinder. The consideration of the spatial local material derivatives provided a more accurate mathematical model of wave propagations through the graded layered structures.     

深部松软煤层钻孔孔周煤体变形产渣特征研究

针对煤矿井下高瓦斯软煤顺层长钻孔排渣困难、成孔率低、施工困难等问题,通过数值模拟实验研究了井下深部软煤体变形破坏特征,分析了顺层长钻孔孔周松软煤体变形特征及应力变化,以揭示顺层长钻孔孔周松软煤体变形产渣规律。研究表明:深部高瓦斯软煤顺层钻孔孔周煤体的应力平衡临界条件破坏后将发生大体积突然垮落;钻孔水平最大变形位移为1.22mm,垂直方向最大变形位移为10.7mm;径向孔周煤体垂向变形呈现逐渐减小趋势,且垂向变形明显大于钻孔水平变形。在水平方向上,钻孔孔周煤体应力分布呈现先增大再逐渐减小的变化规律,径向距离对水平应力分布的影响逐渐减小;随着径向距离的增加,钻孔孔周煤体应力分布逐渐降低,钻孔孔壁处煤体的应力出现最大值,且垂直方向处应力值最大。     

Research on phase shift characteristics of electromagnetic wave in plasma

The phase shift characteristics reflect the state change of electromagnetic wave in plasma sheath and can be used to reveal deeply the action mechanism between electromagnetic wave and plasma sheath. In this paper, the phase shift characteristics of electromagnetic wave propagation in plasma were investigated. Firstly, the impact factors of phase shift including electron density,collision frequency and incident frequency were discussed. Then, the plasma with different electron density distribution profiles were employed to investigate the influence on the phase shift characteristics. In a real case, the plasma sheath around the hypersonic vehicle will affect and even break down the communication. Based on the hypersonic vehicle model, we studied the electromagnetic wave phase shift under different flight altitude, speed, and attack angle. The results indicate that the phase shift is inversely proportional to the flight altitude and positively proportional to the flight speed and attack angle. Our work provides a theoretical guidance for the further research of phase shift characteristics and parameters inversion in plasma.     

Design and validation of robotic bionic eye with multiple flexible ropes parallel mechanism inspired by oculomotor law

Producing a stable and agile bionic eye for visual image acquisition in robotics is a challenging task. In this paper, we design a bionic eye with mirror-symmetric distribution and cross-connection of flexible ropes. This mechanism is based on oculomotor law and the physiological structure of the extraocular muscles (EOMs). Specifically, the basic structural parameters are determined by Listing’s law, and the unique connection of the flexible ropes can realize the functions of the recti and oblique muscles. Furthermore, to mimic the trochlea structure, a pulley mechanism is constructed to permit the free movement of the flexible ropes. Through simulation and physical experiments, it is demonstrated that the bionic eye mechanism can move with agility under the structural parameters. The experimental results indicate that the proposed bionic eye mechanism has a superior motion accuracy of 2.798 mm, which is 6.7% of the maximum motion distance, and the repeatable accuracy of the mechanism can up to 0.210 mm.     

Experimental investigation of unconfined spherical and cylindrical flame propagation in hydrogen-air mixtures

This paper presents results of experimental investigations on spherical and cylindrical flame propagation in pre-mixed H₂/air-mixtures in unconfined and semi-confined geometries. The experiments were performed in a facility consisting of two transparent solid walls with 1 m² area and four weak side walls made from thin plastic film. The gap size between the solid walls was varied stepwise from thin layer geometry (6 mm) to cube geometry (1 m). A wide range of H₂/air-mixtures with volumetric hydrogen concentrations from 10% to 45% H₂ was ignited between the transparent solid walls. The propagating flame front and its structure was observed with a large scale high speed shadow system. Results of spherical and cylindrical flame propagation up to a radius of 0.5 m were analyzed. The presented spherical burning velocity model is used to discuss the self-acceleration phenomena in unconfined and unobstructed pre-mixed H₂/air flames.     

Modeling and analysis of passive worm propagation in the P2P file-sharing network

A number of worms, named P2P (peer-to-peer) passive worms, have recently surfaced, which propagate in P2P file-sharing networks and have posed heavy threats to these networks. In contrast to the majority of Internet worms, it is by exploiting users’ legitimate activities instead of vulnerabilities of networks in which P2P passive worms propagate. This feature evidently slows down their propagation, which results in them not attracting an adequate amount of attention in literature. Meanwhile, this feature visibly increases the difficulty of detecting them, which makes it very possible for them to become epidemic. In this paper, we propose an analytical model for P2P passive worm propagation by adopting epidemiological approaches so as to identify their behaviors and predict the tendency of their propagation accurately. Compared with a few existing models, dynamic characteristics of P2P networks are taken into account. Based on this proposed model, the sufficient condition for the global stability of the worm free equilibrium is derived by applying epidemiological theories. Large scale simulation experiments have validated both the proposed model and the condition.     

环保法规对船舶涂料企业的冲击及应对措施的探讨

随着我国环境保护法规《大气污染防治法》的修订和《涂料征收消费税通知》的公布,探讨了其对船舶涂料企业的冲击及其应对措施。