Topology optimization of flexure hinges with a prescribed compliance matrix based on the adaptive spring model and stress constraint

This paper focuses on the configuration design of flexure hinges with a prescribed compliance matrix and preset rotational center position. A new method for the topology optimization of flexure hinges is proposed based on the adaptive spring model and stress constraint. The hinge optimization model is formulated by maximizing the bending displacement with a spring while optimizing the compliance matrix to a prescribed value. To avoid numerical instability, an artificial spring is used as an auxiliary calculation, and a new strategy is developed for adaptively adjusting the spring stiffness according to the prescribed compliance matrix. The maximum stress of flexure hinge is limited by using a normalized P-norm of the effective von Mises stress, and a position constraint of rotational center is proposed to predetermine the position of the rotational center. In addition, to reduce the error of the stress measurement, a simple but effective filtering method is presented to obtain a complete black-and-white design. Numerical examples are used to verify the proposed method. Topology results show that the obtained flexure hinges have the prescribed compliance matrix and preset rotational center position while also meeting the stress requirements.     

Stress-deformable state of isotropic double curved shell with internal cracks and a circular hole

This work is devoted to the stress–strain state of isotropic double curved shell with defect system. The construction is weakened by two non-through thickness (internal) cracks of different length and by a circular hole located between cracks. In this study we use the line-spring model. Within the framework of this model cracks are modeled as mathematical cuts of shell’s middle surface. This leads to a two-dimensional problem. The problem is reduced to a system of eight boundary integral equations. To ensure the uniqueness of solution an additional equation is added. In the numerical solution of the problem special quadrature formulas for singular integrals of Cauchy type and the finite difference method are applied. The influence of defects on each other for double curved shell has been investigated. The given theoretical results can be used for the calculation of structural elements with holes, cracks on the strength and fracture toughness in various branches of engineering.     

增效过磷酸钙的增效机制及其对玉米生长的影响

利用猪毛、风化煤和腐植酸钠的水解液为增效剂制备了一种增效过磷酸钙,探讨了增效过磷酸钙的增效机制及其对玉米生长的影响。结果表明,蒸馏水浸提条件下,增效过磷酸钙能减缓水溶磷的释放,具备较高的pH值缓冲性。与普通过磷酸钙相比,增效过磷酸钙处理的玉米生物量平均增加了41.9%,吸磷量和吸钙量分别增加了61.7%和27.8%,根系活力增加了24.3%。该研究结果对过磷酸钙生产的技术改进具有指导意义。     

空间红外大口径折射式低温镜头设计与验证

针对目标探测类空间红外相机大范围成像、高灵敏度探测、高精度定位等应用需求,文中提出采用像方远心光路和低温光学技术结合的解决方案,设计了物方视场角8°×8°、入瞳口径265 mm、工作温度200 K的像方远心折射式光学系统。镜头最大口径280 mm,采用多级分散的弹性支撑设计,解决大口径低温透镜装框、透镜组件支撑和镜头整体安装各环节的热应力卸载问题。在保证高刚度和低漏热的情况下,使低温下透镜的热应力对镜头能量集中度的影响降低到可接受范围内。镜头完成装调及室温下像质确认后,进行了力学振动试验,并将其制冷到200 K水平测试像质,测试结果表明,镜头能量集中度达到轴上75%,边缘视场72%。     

恢复邢台百泉泉水流量可行性研究

通过百泉泉区天然状态与超采状态下的水环境对比分析,并对岩溶水补给量和开采量进行计算,阐述恢复邢台百泉泉水流量的可行性,随着“引朱济邢”和“南水北调”供水工程的实施,邢台百泉水生态环境的恢复将变为现实。     

不同管距时玉米渗灌效果的试验研究

在运城市夹马口灌区和红旗灌区进行了1996,1997两个年度的玉米渗灌试验,研究了不同毛管间距条件下渗灌对其产量及水分生产率等的影响。结果表明,玉米渗灌毛管间距采用0.8~1.0 m较为适宜。毛管间距愈大,产量愈低;渗灌较地面灌平均减产7.23%,较旱地平均增产30.8%;玉米生长期内总耗水量地面灌最大,渗灌次之,旱地最小。渗灌可明显提高玉米水分生产率,渗灌处理水分生产率平均为1.65 kg/m3,是地面灌的1.2倍,是旱地的1.33倍;两年度渗灌较地面灌平均节水44.4%。     

Natural occurrence of Fusarium toxins in peanut,sorghum and maize from Mysore (India)

Peanut, sorghum and maize samples were collected from the wholesale market in Mysore, India, over a period of one year (October 1984 to September 1985). The samples were analysed for the natural occurrence of T-2 toxin (T-2), diacetoxyscirpenol (DAS) and zearalenone by thin-layer chromatography, dermal toxicity test and gas chromatography. Of the total number of peanut samples analysed, 6.9% were positive for the toxic trichothecene(s) (T-2, up to 38.89 mg kg^?1; DAS, up to 2.03 mg kg^?1); 4.8% of total sorghum samples analysed contained T-2 up to 15 mg kg^?1. Zearalenone was not found in any of the samples tested, and no toxins were detected in any of the maize samples. Samples marketed during winter and summer periods were contaminated with the toxins. All the toxin-positive samples except one peanut sample were found in produce stored for more than a week.     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

潜油电机碟形弹簧的动力学分析

为了降低潜油电泵机组的振动对止推轴承性能的影响,在潜油电机中节和下节的止推轴承静块底部安装了蝶形弹簧。用有限元方法进行模态分析,确定了蝶形弹簧的主振型和固有频率,然后进行瞬态动力学分析,求解蝶形弹簧在一定载荷下的应力和位移。依此设计的蝶形弹簧将进一步延长止推轴承的使用寿命。