基于VMD和BSA-KELM的高陡边坡位移预测模型研究

边坡位移的时间序列曲线存在复杂的非线性特性,传统的预测模型精度不足以满足预测要求。为此提出了基于变分模态分解的鸟群优化-核极限学习机的预测模型,并用于河北省某水泥厂的边坡位移预测。该方法首先采用VMD把边坡位移序列分解为一系列的有限带宽的子序列,再对各子序列分别采用相空间重构并用核极限学习机预测,采用鸟群算法优化相空间重构的嵌入维度和KELM中惩罚系数和核参数三个数值,以取得最优预测模型。最后将各个子序列预测值叠加,得到边坡位移的最终预测值。结果表明：和KELM、BSA-KELM、EEMD-BSA-KELM模型相比,基于VMD的BSA-KELM预测精度更高,为边坡位移的预测提供一种有效的方法。     

Fabrication of alumina ceramics with functional gradient structures by digital light processing 3D printing technology

Alumina ceramics with different unit numbers and gradient modes were prepared by digital light processing (DLP) 3D printing technology. The side length of each functional gradient structure was 10 mm, the porosity ratio was controlled to 70%, and the number of units were (1 × 1 × 1 unit) and (2 × 2 × 2 unit) respectively. The different gradient modes were named FCC, GFCC-1, GFCC-2 and GFCC-3. SEM, XRD, and other characterization methods proved that these gradient structures of alumina ceramics had only α-Al2O3 phase and good surface morphology. The mechanical properties and energy absorption properties of alumina ceramics with different functional gradient structures were studied by compression test. The results show that the gradient structure with 1 × 1 × 1 unit has better mechanical properties and energy absorption properties when the number of units is different. When the number of units is the same, GFCC-2 and GFCC-3 gradient structures have better compressive performance and energy absorption potential than FCC structures. The GFCC-2 gradient structure with 1 × 1 × 1 unit has a maximum compressive strength of 19.62 MPa and a maximum energy absorption value of 2.72 × 105 J/m3. The good performance of such functional gradient structures can provide new ideas for the design of lightweight and compressive energy absorption structures in the future.     

A hybrid homogeneously weighted moving average control chart for process monitoring: Discussion

The sensitivity of a monitoring scheme depends on many factors including the variance of the charting statistic which is very important in the computation of the control limits. This paper discusses the computation of the variance of the recently proposed hybrid homogeneously weighted moving average (HHWMA) $\overline{X}$ scheme which was based on an incorrect assumption. The correct variance is used to evaluate the run-length characteristics of the HHWMA $\overline{X}$ scheme. It is observed that the incorrect variance has a significant impact on the sensitivity (or performance) of the HHWMA $\overline{X}$ scheme.     

基于梯度提升决策树的车轮轮缘厚度磨耗预测

轮对在列车走行过程中起着导向、承受以及传递载荷的作用，其踏面及轮缘磨耗对地铁列车运行安全性和钢轨的寿命都将产生重要影响。根据地铁列车车轮磨耗机理，分析车轮尺寸数据特点，针对轮缘厚度这一型面参数，基于梯度提升决策树算法构建轮缘厚度磨耗预测模型。在该模型的基础上，任意选取某轮对数据进行验证分析，结果表明：基于梯度提升决策树的轮对磨耗预测模型具有较好的预测精度，可预测出1~6个月的轮缘厚度变化趋势范围，预测时间范围较长，可为地铁维保部门对轮对的维修方式由状态修转为预防修提供指导性建议。     

Event-triggered variable horizon Supervisory Predictive control of hybrid power plants

The supervision of a hybrid power plant, including solar panels, a gas microturbine and a storage unit operating under varying solar power profiles is considered. The Economic Supervisory Predictive controller assigns the power references to the controlled subsystems of the hybrid cell using a financial criterion. A prediction of the renewable sources power is embedded into the supervisor. Results deteriorate when the solar power is unsteady, owing to the inaccuracy of the predictions for a long-range horizon of 10 s. The receding horizon is switched between an upper and a lower value according to the amplitude of the solar power trend. Theoretical results show the relevance of horizon switching, according to a tradeoff between performance and prediction accuracy. Experimental results, obtained in a Hardware In the Loop (HIL) framework, show the relevance of the variable horizon approach. Power amplifiers allow us to simulate virtual components, such as a gas microturbine, and to blend their powers with that of real devices (storage unit, real solar panels). In this case, fuel savings, reaching 15%, obtained under unsteady operating conditions lead to a better overall performance of the hybrid cell. The overall savings obtained in the experiments amount to 12%.     

Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

Evolving an Accurate Decision Tree-Based Model for Predicting Carbon Dioxide Solubility in Polymers

Solubility is one of the most indispensable physicochemical properties determining the compatibility of components of a blending system. Research has been focused on the solubility of carbon dioxide in polymers as a significant application of green chemistry. To replace costly and time-consuming experiments, a novel solubility prediction model based on a decision tree, called the stochastic gradient boosting algorithm, was proposed to predict CO₂ solubility in 13 different polymers, based on 515 published experimental data lines. The results indicate that the proposed ensemble model is an effective method for predicting the CO₂ solubility in various polymers, with highly satisfactory performance and high efficiency. It produces more accurate outputs than other methods such as machine learning schemes and an equation of state approach.     

Gradient-based recursive parameter estimation for a periodically nonuniformly sampled-data Hammerstein–Wiener system based on the key-term separation

The identification of the Hammerstein–Wiener (H-W) systems based on the nonuniform input–output dataset remains a challenging problem. This article studies the identification problem of a periodically nonuniformly sampled-data H-W system. In addition, the product terms of the parameters in the H-W system are inevitable. In order to solve the problem, the key-term separation is applied and two algorithms are proposed. One is the key-term-based forgetting factor stochastic gradient (KT-FFSG) algorithm based on the gradient search. The other is the key-term-based hierarchical forgetting factor stochastic gradient (KT-HFFSG) algorithm. Compared with the KT-FFSG algorithm, the KT-HFFSG algorithm gives more accurate estimates. The simulation results indicate that the proposed algorithms are effective.     

探讨加强质量监督管理提高电网安全水平

电网的安全水平主要取决于其使用产品的质量是否过关。如果产品的质量较好，则能建造出优质的电网，电网的安全水平便会随之提高。因此，应加强对产品质量的监督管理，从而提高电网的安全水平。我们可建立质量监督管理系统，及时抽检出质量不过关的产品，从而消除电网运行过程中潜在的安全隐患。