Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

细旦涤纶50/长绒棉30/丽赛20 7.3 tex高支纱的开发

介绍了细旦涤纶50/长绒棉30/丽赛20纤维的性能,及其混纺纱的生产加工工艺,针对生产中存在的问题,采取了有效的措施,生产的7.3 tex混纺纱线,满足了市场的要求。     

New Engineered Particles from Spray Dryers: Research Needs in Spray Drying

This article reviews developments in the simulations of spray dryer behavior, including the challenges in modeling the complex flow patterns inside the equipment, which are often highly transient and three-dimensional in nature. There appears to be considerable scope for using CFD simulations for investigating methods to reduce the rates of wall deposition and of thermal degradation for particles by modifying the air flow patterns in the chamber through small changes in the air inlet geometry. Challenges include building particle drying kinetics and reaction processes, as well as agglomeration behavior, into these simulations. The numerical simulations should be valuable supplements to pilot-scale testing, enabling more extensive and accurate optimization to be carried out than hitherto possible. New understanding of reaction processes and materials science, in combination with recent knowledge of the application of CFD to these problems, may enable new engineered powder products to be developed from the one-step spray-drying process.     

Characterization of Tomato Pulp Stickiness during Spray Drying using a Contact Probe Method

A contact probe test was developed to characterize the surface stickiness of a tomato pulp droplet at various moisture contents and temperatures. To provide tomato pulp samples with different moisture contents, tomato powder produced by a laboratory spray dryer was wetted to seven different moisture levels. The instantaneous tensile force curve was recorded during the probe withdrawal from which the maximum tensile force and other useful information were obtained and cross-examined against images of bonding, debonding, and failure of the material. Generally, at higher moisture contents tomato pulp exhibited cohesive failure followed by semi-adhesive failure, but when moisture content decreased to a certain level, a peak tensile pressure was observed and the failure was adhesive. In addition, higher temperatures shifted the points of adhesive failure toward lower moisture content.     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

DRYING OF GRANULAR PARTICLES IN A MULTISTAGE INCLINED FLUIDIZED BED WITH MECHANICAL VIBRATION

A mathematical model for the drying rate of granular particles in a multistage inclined fluidized bed(IFB) is presented from the standpoint of simultaneous heat and mass transfer, with taking the effect of mechanical vibration added vertically into consideration.

Steady-state distributions for the temperatures and concentrations of the particles and the heating gas, and for the moisture content of the particles are numerically calculated based on the present model. The calculated results show fairly good agreement with the experimental data, which were obtained from the drying experiments of brick particles in a three-stage IFB using comparatively low temperature air(40-60°C) as the heating gas.

It has been found within the range of the experimental conditions employed that, the mechanical vibration added vertically enhances the over-all drying rate of the particles and its effect can be considered equivalent to an increase in the air velocity.     

Atmospheric Freeze Drying—Modeling and Simulation of a Tunnel Dryer

Drying is an important unit operation in processing of foods and other biotechnological products. Vacuum freeze drying is said to be the best drying technology regarding product quality of the end product, but the disadvantages are, among others, expensive operational costs and batch drying. Atmospheric freeze drying was introduced to lower the production costs of high-quality dried foods, and the need of simulation tools became important in estimations of the industrial drying processes.

A simplified mathematical model (AFDsim) is developed based on uniformly retreating ice front (URIF) considerations. The model is used to calculate theoretical drying curves of atmospheric freeze dried foods in a tunnel dryer. Studies of thermal and mass transfer properties during drying are essential for understanding the changes in product quality and for designing and dimensioning the drying process. The model can be used to simulate industrial atmospheric freeze drying of different foodstuff in a tunnel. The results from AFDsim modeling are in good accordance with the experimental results.     

仪表空气干燥器控制系统的升级改进

利用工厂现有优势资源,自主对故障率逐步升高的仪表空气干燥器控制系统进行升级改进,从而提高重要单元设备运行的可靠性。     

用质子激发X射线分析方法进行人发微量元素的分析研究

一、序言 质子激发X射线分析方法是瑞典人约翰逊在1970年首先提出来的。由于它具有灵敏度高、取样少、无损伤、快速、适用范围广等特点,使它在十余年中在生物医学、环境科学、地质、冶金、考古学和法学等领域得到了广泛的应用。我们应用质子激发X射线分析方法分析了人发中的微量元素。