某340矫直机上辊快开机构裂纹原因分析及预防措施

340管线矫直机是太原重工成熟产品,在国内占有较大市场,并出口印度、印尼、缅甸、埃及等国际市场。出口印度矫直机在质保期内出现主缸裂纹问题,为探明问题原因并杜绝类似情况发生,快开机构设计静强度分析、疲劳强度分析及生产加工过程等方面探查裂纹原因并提出几点预防措施。     

微裂隙中水泥浆液渗滤效应的可视化试验研究

在微裂隙岩体注浆过程中,水泥浆液的渗滤效应对注浆效果的影响显著。自主研制了一套微裂隙注浆可视化试验系统,该系统由注浆系统、微裂隙模型以及监测系统3个部分组成,监测系统又分为显微监测系统和压力流量监测系统。当水泥浆液进入微裂隙模型后,利用显微监测系统对裂隙入口处的渗滤效应进行实时观测。利用压力流量监测系统对注浆试验过程中的注浆压力以及累计流量进行自动记录。运用自主设计的微裂隙注浆可视化试验系统,对微裂隙中的水泥浆液渗滤过程进行试验研究。采用3种水泥浆材(超细水泥Ⅰ、超细水泥Ⅱ和普通水泥),研究在注浆压力2.0 MPa、水灰比1.0的条件下,不同水泥颗粒粒径大小在不同裂隙开度下的浆液渗滤效应。通过试验发现,当裂隙开度较小时,在裂隙入口处形成了完整的半圆拱形滤饼;随着裂隙开度的增加,在裂隙入口处形成断续分布状滤饼;当裂隙开度增加到无渗滤发生时,裂隙入口处仅残留少量水泥颗粒附着物。通过试验获得了3种水泥的最小可注入裂隙开度大小b min和最小无渗滤裂隙开度大小b crit:超细水泥Ⅰ的b min和b crit分别为80和280μm;超细水泥Ⅱ的b min和b crit分别为100和300μm;普通水泥的b min和b crit分别为140和310μm。研究结果发现水泥粒径的减小对最小可注入裂隙开度大小的影响较大,但对最小无渗滤裂隙开度大小的影响较小。结合渗滤趋势k值,发现随着水泥粒径的减小,相应的k min和k crit值会随之增加,水泥浆液更容易在裂隙入口处发生渗滤,这是因为超细水泥比表面积更大,水泥颗粒间易发生团聚。     

Ring‐opening polymerization of lactones initiated by diphenylzinc–coinitiator systems

Diphenylzinc, alone or in combination with water and butanone as coinitiators, was used as a polymerization initiator system for a variety of lactones at varying temperatures. The resulting data indicate that the course of the polymerization is greatly influenced by the lactone structure, as well as by the molar ratio of coinitiator to diphenylzinc. When used alone, diphenylzinc exhibited high activity as an initiator in δ‐valerolactone polymerizations, although it was less efficient when used in the β‐butyrolactone and the β‐propiolactone polymerizations. Activity in the polymerization of β‐lactones was increased by adding small amounts of butanone or water. It was also observed that the diphenylzinc–butanone combination was more effective than the diphenylzinc–water mixture in the polymerizations of β‐butyrolactone and β‐propiolactone. Copyright © 2003 Society of Chemical Industry     

Ring‐opening polymerization of D,L‐lactide by rare earth 2,6‐dimethylaryloxide

Ring‐opening polymerization of D,L ‐lactide (LA) has been successfully carried out by using rare earth 2,6‐dimethylaryloxide (Ln(ODMP)₃) as single component catalyst or initiator for the first time. The effects of different rare earth elements, solvents, monomers and catalyst concentration as well as polymerization temperature and time on the polymerization were investigated. The results show that La(ODMP)₃ exhibits higher activity to prepare poly(D,L ‐lactide) (PLA) with a viscosity molecular weight of 4.5 × 10⁴ g mol^?1 and the conversion of 97 % at 100 °C in 45 min. The catalytic activity of Ln(ODMP)₃ has following sequence: La > Nd > Sm > Gd > Er > Y. A kinetic study has indicated that the polymerization is first order with respect to both monomer and catalyst concentration. The apparent activation energy of the polymerization of LA with La(ODMP)₃ is 69.6 kJ mol^?1. The analyses of polymer ends indicate that the LA polymerization proceeds according to ‘coordination–insertion’ mechanism with selective cleavage of the acyl–oxygen bond of the monomer. Copyright © 2004 Society of Chemical Industry     

火焰图像特征在火灾数字图像识别中的运用

火焰尖角数目和圆形度是早期火灾火焰的主要特征,本文主要论述了如何在数学形态学基础上,利用火灾火焰的两个特点判断和识别早期火情。实验中,对火焰的二值图像进行开运算,即先腐蚀,再膨胀,目的是为了对火焰图像进行形态学滤波,去噪。从实验结果可以看出,该算法可以很好的识别火焰和干扰源。     

苯并口恶嗪-环氧化合物-胺类催化剂体系开环聚合反应的研究

采用TLC，GPC，1H－NMR及IR等分析方法，对苯并恶嗪－环氧化合物－胺类催化剂体系的聚合反应进行了研究，表征了产物结构，并探讨了聚合反应机理，结果表明，苯并恶唪－环氧化合物体系在胺类催化剂如苄胺，咪唑的作用下，能发生开环聚合反应，生成低分子量的聚合物。     

Determining stress intensity factors of composites using crack opening displacement

The main purpose of this paper is to find the mixed-mode stress intensity factors of composite materials using the crack opening displacement (COD). First, a series solution of the composite material with a crack was used to evaluate COD values. Then, the least-squares method was used to calculate mixed-mode stress intensity factors. This algorithm can be applied to any method that generates or measures COD values. The major advantage of this method is that COD values very near the crack tip are not necessary. Both finite element simulations and laboratory experiments were applied to validate this least-squares method with acceptable accuracy if the even terms of the series solution are removed.     

涤纶超细仿麂皮织物染整实践

介绍了涤纶超细仿麂皮织物的染整加工工艺，重点分析了前处理、染色等关键工序，并给出了具体工艺参数。     

Analysis of crack tip plasticity for microstructurally small cracks using crystal plasticity theory

Crack tip plastic zone sizes and crack tip opening displacements (CTOD) for stationary microstructurally small cracks are calculated using the finite element method. To simulate the plastic deformation occurring at the crack tip, a two-dimensional small strain constitutive relationship from single crystal plasticity theory is implemented in the finite element code ANSYS as a user-defined plasticity subroutine. Small cracks are modeled in both single grains and multiple grains, and different crystallographic conditions are considered. The computed plastic zone sizes and CTOD are compared with those found using conventional isotropic plasticity theory, and significant differences are observed.     

An investigation of crack closure and the propagation of semi-elliptical fatigue cracks in Q1N (HY80) pressure vessel steel

The results of an experimental investigation of the effect of crack closure on the propagation of semi-elliptical fatigue cracks are presented. Load-shedding fatigue threshold tests were carried out at stress ratios of 0.2, 0.35, 0.5 and 0.7. Crack closure was measured at the surface and depth positions using backface strain gauges, near-tip gauges, and a clip gauge. Differences between the surface and depth growth behaviour are explained by considerations of the effects of the transition from plane stress conditions at the surface to plane strain conditions at the depth. The effects of stress ratios are attributed largely to differences in the crack opening displacement, which result in asperities coming into contact to induce roughness-induced crack closure.