Microstructure,mechanical, tribological,and oxidizing properties of AlCrSiN/AlCrVN/AlCrNbN multilayer coatings with different modulated thicknesses

Multilayer structure design is one of the most promising methods for improving the comprehensive performance of AlCrN-based hard coatings applied to cutting tools. In this study, four types of AlCrSiN/AlCrVN/AlCrNbN multilayer coatings, with different modulated thicknesses, were deposited to investigate their microstructure, mechanical, tribological, and oxidizing properties. All multilayer coatings exhibited grain growth along the crystallographic plane of (200) with a NaCl-type face-centered cubic (FCC) structure. The results show that, as the modulation thickness decreases from ～35 nm to ～10 nm, (1) the grain refinement effect is increasingly evident; (2) all multilayer coatings show a hardness of >30 GPa and an elastic modulus of >300 GPa. Both the ability to resist elastic strain to failure and the plastic deformation of multilayer coatings increase. In addition, their resistance to cracking reduces; (3) the wear rates of these multilayer coatings reduce successively from 1.78 × 10^?16 m³ N^?1 m^?1 to 7.7 × 10^?17 m³ N^?1 m^?1. This is attributed to an increase in self-lubricating VO_x and a decrease in adhesives from the counterparts; (4) the best high-temperature oxidation resistance was obtained for the multilayer coating with a modulated thickness of ～15 nm.     

Numerical simulation of water and heat transport in the cathode channel of a PEM fuel cell

Cathode channel of a PEM fuel cell is the critical domain for the transport of water and heat. In this study, a mathematical model of water and heat transport in the cathode channel is established by considering two-phase flow of water and air as well as the phase change between water and vapor. The transport process of the species of air is governed by the convection-diffusion equation. The VOSET (coupled volume-of-fluid and level set method) method is used to track the interface between air and water, and the phase equilibrium method of water and vapor is employed to calculate the mass transfer rate on the two-phase interface. The present model is validated against the results in the literature, then applied to investigate the characteristics of two-phase flow and heat transfer in the cathode channel. The results indicate that in the inlet section, water droplets experience three evolution stages: the growing stage, the coalescence stage and the generation stage of dispersed water drops. However, in the middle and outlet sections of the channel, there are only two stages: the growth of water droplets, and the formation of a water film. The mass transfer rate of phase change in the inlet section of the channel varies over time, exhibiting an initial increase, a decrease followed, and a stabilization finally, with the maximum and stable values of 1.78 × 10^?4 kg/s and 1.52 × 10^?4 kg/s for Part 1, respectively. In the middle and outlet sections, the mass transfer rate increase firstly and then keeps stable gradually. Furthermore, regarding the distribution of the temperature and vapor mass fraction in the channel, near the upper surface of the channel, the temperature and vapor mass fraction first change slightly (x < 0.03 m) and then rapidly decrease with fluctuations (x > 0.03 m). In the middle of the channel, the temperature and vapor mass fraction slowly decrease with fluctuation.     

Cold and wet: Diatoms dominate the phytoplankton community during a year of anomalous weather in a Great Lakes estuary

As sentinels of climate change and other anthropogenic forces, freshwater lakes are experiencing ecosystem disruptions at every level of the food web, beginning with the phytoplankton, a highly responsive group of organisms. Most studies regarding the effects of climate change on phytoplankton focus on a potential scenario in which temperatures continuously increase and droughts intersperse heavy precipitation events. Like much of the conterminous United States in 2019, the Muskegon River watershed (Michigan, USA) experienced record-breaking rainfall accompanied by unusually cool temperatures, affording an opportunity to explore how an alternate potential climate scenario may affect phytoplankton. We conducted biweekly sampling of environmental variables and phytoplankton in Muskegon Lake, a Great Lakes Area of Concern that connects to Lake Michigan. We compared environmental variables in 2019 to the previous eight years using long-term data from the Muskegon Lake Observatory buoy, and annual monitoring excursions provided historical phytoplankton data. Under cold and wet conditions, diatoms were the single dominant division throughout the entire growth season – an unprecedented scenario in Muskegon Lake. In 10 of the 13 biweekly sampling days in 2019, diatoms comprised over 75% of the phytoplankton community in the lake by count, indicating that the spring diatom bloom persisted through the fall. Additionally, phytoplankton seasonal succession and abundance patterns typically seen in this lake were absent. In a world experiencing reduced predictability, increased variability, and regional climate anomalies, studying periods of extreme weather events may offer insight into how natural systems will be affected and respond under future climate scenarios.     

Influence of temperature on acoustic emission source location accuracy in underground structure

An acoustic emission (AE) experiment was carried out to explore the AE location accuracy influenced by temperature. A hollow hemispherical specimen was used to simulate common underground structures. In the process of heating with the flame, the pulse signal of constant frequency was stimulated as an AE source. Then AE signals received by each sensor were collected and used for comparing localization accuracy at different temperatures. Results show that location errors of AE keep the same phenomenon in the early and middle heating stages. In the later stage of heating, location errors of AE increase sharply due to the appearance of cracks. This provides some beneficial suggestions on decreasing location errors of structural cracks caused by temperature and improves the ability of underground structure disaster prevention and control.     

Effects of the film thickness and poling electric field on photovoltaic performances of (Pb,La)(Zr,Ti)O3 ferroelectric thin film-based devices

The ferroelectric photovoltaic (FPV) effect obtained in inorganic perovskite ferroelectric materials has received much attention because of its large potential in preparing FPV devices with superior stability, high open-circuit voltage (V_oc) and large short-circuit current density (J_sc). In order to obtain suitable thickness for the ferroelectric thin film as light absorption layer, in which, the sunlight can be fully absorbed and the photo-generated electrons and holes are recombined as few as possible, we prepare Pb_0.93La_0.07(Zr_0.6Ti_0.4)_0.9825O₃ (PLZT) ferroelectric thin films with different layer numbers by the sol-gel method and based on these thin films, obtain FPV devices with FTO/PLZT/Au structure. By measuring photovoltaic properties, it is found that the device with 4 layer-PLZT thin film (~300 nm thickness) exhibits the largest V_oc and J_sc and the photovoltaic effect obviously depends on the value and direction of the poling electric field. When the device is applied a negative poling electric field, both the V_oc and J_sc are significantly higher than those of the device applied the positive poling electric field, due to the depolarization field resulting from the remnant polarization in the same direction with the built-in electric field induced by the Schottky barrier, and the higher the negative poling electric field, the larger the V_oc and J_sc. At a -333 kV/cm poling electric field, the FPV device exhibits the most superior photovoltaic properties with a V_oc of as high as 0.73 V and J_sc of as large as 2.11 μA/cm². This work opens a new way for developing ferroelectric photovoltaic devices with good properties.     

基于梯度提升决策树的车轮轮缘厚度磨耗预测

轮对在列车走行过程中起着导向、承受以及传递载荷的作用，其踏面及轮缘磨耗对地铁列车运行安全性和钢轨的寿命都将产生重要影响。根据地铁列车车轮磨耗机理，分析车轮尺寸数据特点，针对轮缘厚度这一型面参数，基于梯度提升决策树算法构建轮缘厚度磨耗预测模型。在该模型的基础上，任意选取某轮对数据进行验证分析，结果表明：基于梯度提升决策树的轮对磨耗预测模型具有较好的预测精度，可预测出1~6个月的轮缘厚度变化趋势范围，预测时间范围较长，可为地铁维保部门对轮对的维修方式由状态修转为预防修提供指导性建议。     

Impact assessment of reservoir desiltation measures for downstream riverbed migration in climate change: A case study in northern Taiwan

Typhoon Aere in 2004 induced severe sedimentation and loss of storage capacity of the Shihmen Reservoir in northern Taiwan. The resulting dramatic increase in the turbidity of the water seriously affected the water supply. To effectively maintain the stability of the water supply and maintain the reservoir’s storage capacity, the government of Taiwan began to plan and construct a series of improvement measures, such as a sediment flushing tunnel, the JhongJhuang Bank-Side Reservoir, and the Amuping Desilting Tunnel. However, previous studies only focused on the impact of the sediment flushing tunnel and the Amuping Desilting Tunnel on the downstream riverbed, and did not consider the possibility of increasing sediment discharge after the completion of the JhongJhuang Bank-Side Reservoir. In addition, climate change will cause the intensity of extreme rainfall to increase enormously in the future. That rainfall and extra sediment flushing will challenge the existing flood prevention facilities. Therefore, this study considered that the JhongJhuang Bank-Side Reservoir will increase sediment discharge of the Shihmen Reservoir, and used dynamical downscaling extreme typhoon data of climate change under the RCP 8.5 scenario to explore the flood prevention and riverbed migration of the main channels of the Dahan and Tamsui Rivers in the future. We used the rainfall–runoff model of Hydrologic Modeling System to simulate rainfall and runoff, and used the hydraulic and sediment transport model of CCHE1D to holistically simulate flood events and consequent river scouring and deposition behaviors. Our results showed that the projected peak discharge during the late 21st century (2075 to 2099) will be at least 50% higher than that during the baseline (1979 to 2003) period. In terms of flood prevention, the potential of overbank flooding will increase in the downstream area, and the trend of long-term change in the riverbed will be dominated by degradation (-0.489 ± 0.743 m) in the future. The improvement measures will have a limited impact on riverbed migration (0.011 ± 0.094 m) in the Dahan and Tamsui Rivers. After the operation of the JhongJhuang Bank-Side Reservoir, the Shihmen Reservoir is expected to increase the sediment discharge ratio by 70% during floods, and it will not cause excessive water turbidity that may affect downstream water supply.     

Change detection in synthetic aperture radar images based on unsupervised artificial immune systems

In this paper, we propose a novel change detection method for synthetic aperture radar images based on unsupervised artificial immune systems. After generating the difference image from the multitemporal images, we take each pixel as an antigen and build an immune model to deal with the antigens. By continuously stimulating the immune model, the antigens are classified into two groups, changed and unchanged. Firstly, the proposed method incorporates the local information in order to restrain the impact of speckle noise. Secondly, the proposed method simulates the immune response process in a fuzzy way to get an accurate result by retaining more image details. We introduce a fuzzy membership of the antigen and then update the antibodies and memory cells according to the membership. Compared with the clustering algorithms we have proposed in our previous works, the new method inherits immunological properties from immune systems and is robust to speckle noise due to the use of local information as well as fuzzy strategy. Experiments on real synthetic aperture radar images show that the proposed method performs well on several kinds of difference images and engenders more robust result than the other compared methods.     

Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.