尿素装置液位仪表失真分析及处理

介绍了尿素装置中3起液位仪表失真案例,分析了故障现象和设备工况,确定失真原因,采取了相应的处理措施,解决了仪表故障。     

Deformation-Strength Relationships in Short-Term Tension of Heat-Resistant Materials

The analysis of 124 curves obtained in short-term tensile tests demonstrate that they can be described by varying strain hardening and softening characteristics. Different stress–strain curves can be produced at invariable yield strength and ultimate strength and interrelated proportional variations of the above characteristics. To determine some specific stress–strain curve, it is necessary to take account of yield strength and ultimate strength as well as strain corresponding to the latter. The relations between yield strength, ultimate strength and hardening and their practically complete absence between these parameters and softening were statistically established.     

24万t/a尿素装置技术改造总结

针对新化化肥有限公司尿素装置存在的问题进行了技术改造,从尿素合成塔、中压分解吸收、低压分解吸收、闪蒸等方面分析了产生问题的原因,提出了改进措施和实施方案。对改造前后工艺指标、产品质量和经济效益进行了对比和分析。改造结果表明.生产能力提高25％,5个月可收回全部投资。     

无机阻燃剂高聚合度聚磷酸铵的研制

以五氧化二磷、磷酸铵盐、尿素为原料、氨气为保护气,制备了高聚合度聚磷酸铵无机阻燃剂。考察了五氧化二磷、磷酸铵盐、尿素的用量和反应温度对聚磷酸铵平均聚合度的影响。采用端基滴定法测定了聚磷酸铵的聚合度,并用X射线衍射(XRD)法表征了聚磷酸铵的晶体结构,同时测定了聚磷酸铵的粒度和溶解度。实验结果表明,制备聚磷酸铵的最佳反应条件为:n(磷酸氢二铵)∶n(五氧化二磷)∶n(尿素)=1∶1∶0.3,反应温度280~300℃,反应时间40m in,热处理温度250~280℃,热处理时间110m in。在此条件下制备的聚磷酸铵的平均聚合度大于600,平均粒径直径小于50μm,在水中的溶解度小于0.4g;XRD表征结果表明,所合成的物质为Ⅱ型聚磷酸铵。     

水溶液全循环法尿素装置中压分解"三种工艺"的比较

以生产数据结合理论计算的方法系统地比较、分析了水溶液全循环法尿素装置中中压分解“三种工艺”的热能利用、甲铵分解率、总氨蒸出率、水平衡量、一分加热器生产能力等方面的情况，提出应用和配置预分离-预蒸馏工艺的方法，评论该工艺在水溶液全循环法中的地位和作用。     

大颗粒尿素造粒工艺简介

介绍了大颗粒尿素造粒工艺，着重介绍了荷兰NSM公司的流化床造粒技术和法国K－T公司的流化床转鼓造粒（FDG）技术。     

A One-Dimensional Nonlocal Damage-Plasticity Model for Ductile Materials

This paper presents a new 1-D non-local damage-plasticity deformation model for ductile materials. It uses the thermodynamic framework described in Houlsby and Puzrin (2000) and holds, nevertheless, some similarities with Lemaitre’s (1971) approach. A 1D finite element (FE) model of a bar fixed at one end and loaded in tension at the other end is introduced. This simple model demonstrates how the approach can be implemented within the finite element framework, and that it is capable of capturing both the pre-peak hardening and post-peak softening (generally responsible for models instability) due to damage-induced stiffness and strength reduction characteristic of ductile materials. It is also shown that the approach has further advantages of achieving some degree of mesh independence, and of being able to capture deformation size effects. Finally, it is illustrated how the model permits the calculation of essential work of rupture (EWR), i.e. the specific energy per unit cross-sectional area that is needed to cause tensile failure of a specimen.     

烧结处理小矿山精矿的应用研究

研究小矿山精矿的性质，分析小矿山精矿对烧结过程的影响，提出了增加小矿山精矿配入量的途径及方法．     

尿素醇解合成碳酸酯类化合物技术进展

综述了用尿素醇解合成碳酸酯类化合物的技术进展 ,重点介绍尿素醇解合成碳酸二甲酯研究现状以及与其它工艺路线的比较 ,另外也介绍了尿素醇解合成长碳链脂肪族和芳香族类碳酸酯的研究进展。