Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

Three-phase four-wire shunt active power filter based on the SOGI filter and Lyapunov function for DC bus control

The three-phase four-wire shunt active power filter (SAPF) was developed to suppress the harmonic currents generated by nonlinear loads, and for the compensation of unbalanced nonlinear load currents, reactive power, and the harmonic neutral current. In this work, we consider instantaneous reactive power theory (PQ theory) for reference current identification based on the following two algorithms: the classic low-pass filter (LPF) and the second-order generalized integrator (SOGI) filter. Furthermore, since an important process in SAPF control is the regulation of the DC bus voltage at the capacitor, a new controller based on the Lyapunov function is also proposed. A complete simulation of the resultant active filtering system confirms its validity, which uses the SOGI filter to extract the reference currents from the distorted line currents, compared with the traditional PQ theory based on LPF. In addition, the simulation performed also demonstrates the superiority of the proposed approach, for DC bus voltage control based on the Lyapunov function, compared with the traditional proportional-integral (PI) controller. Both novel approaches contribute towards an improvement in the overall performance of the system, which consists of a small rise and settling time, a very low or nonexistent overshoot, and the minimization of the total harmonic distortion (THD).     

卫星激光通信粗跟踪系统复合控制策略

针对卫星激光通信粗跟踪系统的跟踪稳定精度指标要求高的特点,建立了基于永磁同步电机直接驱动的粗跟踪系统模型并进行了跟踪稳定误差分析。在采用传统PID控制策略存在跟踪误差较大、动态性能较差等不足的基础上,提出了一种基于粗跟踪系统的改进型前馈复合控制策略。从理论上分析了前馈复合控制策略提高了粗跟踪系统的动态性能,为降低跟踪稳定误差提供了改善方案。地面实验验证结果表明,与传统控制策略相比,改进型复合控制策略极大地降低了系统的动态跟踪误差,动态跟踪误差由606μrad降低至13μrad(1δ)。进一步的在轨实验也验证了改进型复合控制策略的合理性和先进性,总体指标满足了卫星激光通信终端的极高精度要求。本文所提出的控制策略对其他高性能跟踪伺服系统设计也具有较大的借鉴意义。     

Structural,electrical, optical and dielectric properties of yttrium substituted cadmium ferrites prepared by Co-Precipitation method

The yttrium substituted cadmium ferrites having composition Cd_1-xY_xFe₂O₄ (X = 0.00, 0.125, 0.250, 0.375, 0.500) were synthesized by the co-precipitation method and sintered at 1100 °C for 6 h. Structural, morphological, electrical, optical and dielectric characteristics were explored by XRD, SEM, EDS, FTIR, I–V two probes, UV–Vis and LCR techniques.XRD results confirmed the cubic structure of spinel ferrites. A decrease in lattice constants of the prepared samples was observed with the substitution of Y ions and was attributed to the difference in ionic radii of Y³⁺ (0.95 Å) and Cd²⁺ (0.97 Å) ions. Cationic distributions, ionic radii of both tetrahedral and octahedral sites, tolerance factor, oxygen positional parameters, bond lengths, interatomic distances, positional parameters and bond length angles were calculated from XRD data. The morphology of the prepared ferrites was studied using SEM and results ratified the XRD results. EDS confirmed the presence of all inserted elements in Cd_1-xY_xFe₂O₄ composition. DC resistivity and drift mobility of soft-ferrites were found to be increased from 1.047 × 10⁸–4.822 × 10¹⁰ Ω-cm and 5.87 × 10⁻¹² – 1.045 × 10⁻¹⁴ cm²V⁻¹s⁻¹, respectively, at 523 K with yttrium content confirming the behavior of semiconductor materials. The optical band gap energy calculated from the UV–Vis pattern of the Cd_1-xY_xFe₂O₄ system was decreased from 3.6011 to 2.8153 eV. DC resistivity and optical band gaps exposed inverse relation. FTIR results revealed lower and upper-frequency absorption bands in the ranges of 419.31–417.01 cm⁻¹ and 540.95–565.70 cm⁻¹, respectively. Dielectric constant and dielectric losses were in decreasing order, while ac conductivity revealed rising behavior with increasing frequency. Results showed the potential of yttrium doped Cd nanoferrites for applications in high-frequency microwave absorbing devices.     

基于ＰＩＤ控制算法的直流微网容错控制方法研究

构建直流微网容错控制对象模型，调节直流微电网的输出回路参数；以输出功率、直流微网的 参考电压、弱电网下系统惯性响应特征等为约束参量，构建直流微网容错控制目标函数，在不同电网强度下 进行直流微网容错控制的参数自整定性调节，采用无功环比例积分控制方法进行直流微网容错寻优分析， 建立模糊 ＰＩＤ控制模型，采用变结构的模糊 ＰＩＤ控制方法进行直流微网容错控制过程中的自适应加权学习 和误差反馈调节，实现直流微网容错控制改进设计。仿真结果表明，采用该方法进行直流微网控制的容错 性能较好，输出稳定性较强，具有较好的直流微网输出增益。     

浅谈DC/DC变换器控制新方法

文中针对DC/DC变换器的特点,在现有控制和建模方法的基础之上,对DC/DC变换器的现代控制方法进行了归纳和总结,简要讨论了其控制原理,并比较了各种现代控制方法的优缺点,最后对DC/DC变换器控制方法的发展作了一定的展望。     

DC/DC电源中的电磁干扰及其对策

概述了电磁干扰(EMI)和电磁兼容(EMC)的基本知识，对DC／DC电源中的电磁干扰进行了综合分析，并给出了各自的解决方案。     

用于磁场测量的高精度500A/30V零压开关直流稳流电源

研制了一种带有无源辅助网络的全桥移相脉宽调制零压开关(FB PSPWMZVS)高精度磁铁稳流电源,并在电磁铁磁场测量中得到应用,其电流稳定度在8h内优于±1×10-4。