Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.     

基于时频域的卷积神经网络运动想象脑电信号识别方法

针对目前运动想象脑电（EEG）信号识别率较低的问题，考虑到脑电信号蕴含着丰富的时频信息，提出一种基于时频域的卷积神经网络（CNN）运动想象脑电信号识别方法。首先，利用短时傅里叶变换（STFT）对脑电信号的相关频带进行预处理，并将多个电极的时频图组合构造出一种二维时频图；然后，针对二维时频图的时频特性，通过一维卷积的方法设计了一种新颖的CNN结构；最后，通过支持向量机（SVM）对CNN提取的特征进行分类。基于BCI数据集的实验结果表明，所提方法的平均识别率为86.5%，优于其他传统运动想象脑电信号识别方法；同时将该方法应用在智能轮椅上，验证了其有效性。     

自然循环工况下离心泵阻力特性的实验研究与数值模拟

停转后泵的阻力特性对自然循环流量影响明显。为研究低流量自然循环工况下离心泵的阻力特性，设计了实验台架，对离心泵的正向压降、反向压降和损失系数进行了测量，实验雷诺数为2.0×10⁴～1.5×10⁵。实验表明：相同雷诺数下，反向压降明显高于正向压降；雷诺数大于8×10⁴时，损失系数基本保持不变，而低雷诺数下损失系数随雷诺数的降低有增大的趋势；基于实验得到了损失系数的经验关系式。采用CFD方法对离心泵的内部流场进行了模拟，计算表明：CFD方法能较好地预测损失系数，RNG k-ε模型与实验值的相对误差不超过10%；离心泵的压力损失主要集中在叶轮、导叶等结构的交界区域；正向与反向流动的流场分布存在显著区别；低雷诺数下局部流动更加不稳定。     

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics–based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.     

可重构机器人模块间装配误差识别方法研究

基于对可重构机器人配对接口间位姿误差的分析划分,研制模块间装配误差在线测量识别接口,建立配对接口位姿误差与接口几何结构偏差之间的关系模型,进而建立配对接口位姿误差与配对接口内部测距传感器测量值之间的映射关系模型,提出一种基于内部测距传感器位移量的模块间装配误差在线识别、补偿方法.为验证方法的正确性,研制单关节?连杆试验平台.试验结果表明装配误差经在线识别、补偿后,连杆末端的位置误差平均值减少7倍多.     

Ni-P/HZSM-5催化木质素降解制备酚类化学品

采用Ni-P复合改性HZSM-5催化剂催化木质素降解制备高附加值的单酚类化学品，探讨了催化剂种类、金属负载量、反应温度、反应时间以及溶剂种类对木质素催化降解制备酚类化合物的影响。同时采用X射线衍射仪（XRD）、比表面积和孔径分析仪（BET）、化学吸附仪（NH₃-TPD）、热重分析仪（TG）以及气相色谱质谱联用仪（GC/MS）对催化剂以及液相产物进行分析表征，同时探讨其催化失活以及再生机制。结果表明：Ni、P高度分散在HZSM-5催化剂的表面，Ni的添加有效地弱化了C－C键，致使β-O-4和α-O-4发生断裂，有效地提高了木质素加氢解聚的活性，减少了焦炭的生成，但催化剂的再生水热稳定性较差，重复使用性较低。当采用甲醇为供氢试剂，在反应温度为220℃，氢气压力为2MPa，反应时间为8h，催化剂负载量为10%，NaOH为共催化剂时，其木质素的转化率为98.6%，酚类化合物的含量达到74.97%。产物以苯酚、愈创木酚和紫丁香酚为主，低温促进了紫丁香酚的产生。     

Study on Wettability and Corrosion Behavior of Al2O3 Doped Polyurea Coatings

Protection of Metals and Physical Chemistry of Surfaces - The Al2O3 powder was added as a filler to polyurea and the effect of doping amount on Shore hardness and wetting property were...     

电场对竖直矩形微槽群润湿及表面温度的影响

微槽群在热流密度较大时会达到其毛细极限，可通过主动换热方式之一——电水动力学效应对其进行强化。本文为了研究电场对微槽群表面润湿特性和温度分布的影响，采用平板电极提供电场，蒸馏水作为工质，使用高速相机拍摄微槽内液体润湿长度，测量误差为2.97%～7.46%；使用红外热像仪拍摄电场作用下微槽群表面温度分布，测量误差为2.1%～2.39%。热流密度测量误差范围是9.66%～11.11%。结果表明：电场通过驱动微槽内流体向加热区域流动而提升其润湿性能，且较低热流密度下提升更好。因润湿性能的提升，微槽表面温度得以下降。随着电场增强，微槽横向温度分布的“波峰”、“波谷”差别加大，微槽纵向温度明显降低。当热流密度加大时，温降更为显著，1.4W/cm²热流密度、6kV电压下温降可达到30℃以上。温降的增加反映了电场对微槽的强化润湿进一步提升了微槽换热性能，且电场对较高热流情形下的微槽换热有着更为显著的强化效果。     

A computer aided design method for car form and its application based on shape parameters

In the early design stage, automotive modeling should both meet the requirements of aesthetics and engineering. Therefore, a vehicle CAD (computer aided design) model that can be easily adjusted by feedbacks is necessary. Based on CE-Bézier surface, this paper presents a set of algorithms for parametric segmentation and fairing surface generation in a car model. This model is defined by a simplified automotive template and relevant control points, shape parameters and segmentation parameters, which can be modified to alter the car form efficiently. With this model and the corresponding adjustment method, more than fifty various vehicle models are established in this research according to different parameters. And two methods for calculating similarity index between car models are constructed, which are suitable for brand design trend analysis and modelling design decisionmaking.     

潮流能水平轴水轮机在剪切来流下的水动力分析

采用基于计算流体力学方法的全尺度数值模拟计算,建立了适用于潮流能水轮机模拟的剪切来流环境,通过数值计算结果,对潮流能水轮机随时间变化的宏观力和流场特征进行了系统分析,探索水轮机在复杂工况下的水动力特性规律。结果表明,水轮机整个叶轮的总体平均受力在剪切流工况中未受到明显影响; 单个叶片的瞬态轴向力系数和瞬态轴向扭矩系数在旋转周期内出现了明显的周期性变化,且周期性变化幅值随转速增大而增大; 非定常的瞬时轴向扭矩和力的周期性振荡容易引起单个叶片的结构性振动,可能对水轮机的机械结构造成影响。