Effect of O2 on NO removal by ammonia radical injection using one-cycle sinusoidal power source

NO reduction experiment was performed by injecting ammonia radicals, which were externally generated by flowing the NH₃ gas diluted with Ar gas through a dielectric barrier discharge with a one-cycle sinusoidal-wave power source. The discharge was intermittently formed between coaxial cylindrical electrodes with a space of 1.5 mm at an applied peak-to-peak voltage of 3-25 kV. The generated radicals were injected into simulation gas (NO/O₂/N₂). The simulation gas contained 0-5.6% O₂, and the effect of O₂ on NO_x removal was discussed. The minimum reaction temperature for NO reduction was low when simulation gas contained O₂. High O₂ concentration (O₂=5.6%) in simulation gas, high repetition rate to NH₃, and high applied power to NH₃ decreased NO removal efficiency.     

Glasslike Transitions in Thin Polymer-Melt Films Due to Thickness Constraint

The shear properties of thin films of star and linear polyisoprene (PIP) melts under high pressure were investigated as a function of sliding velocity (shear rate) using the surface forces apparatus. The results were contrasted with their bulk rheological properties; effects of thickness constraint on the shear behavior were discussed. The melts of PIP in bulk exhibit Newtonian-like constant viscosity at least at low shear rates (frequencies), which suggests that individual molecules flow with lateral sliding motion. However, thin films of PIP melts show tribological features involving apparent shear-thinning behavior, indicative of the correlated motions in confined geometries. The shear-property change from bulk rheological behavior to thin-film tribological behavior along with the thickness decrease reflects the physical states and their transitions in the systems; the thickness constraint induces glasslike transitions. Effects of molecular weights and molecular architecture (star-branched or linear) on the shear properties are also discussed.     

Voltage Control of Static Var Compensator for a Remote System Interconnected by Long‐Distance AC Cables

The voltage variation in a remote system is large when the system is connected by long‐distance AC cables due to the cable capacitance. In Japan, the longest 54‐km 66‐kV AC submarine cable interconnection between the Kyushu mainland and Goto Islands was commissioned in 2005. It was requested to mitigate the voltage variation caused by switching off and on one circuit of the two circuits in the AC cables when a fault occurs. Since the conventional voltage control methods such as transformer tap changer or shunt capacitor and reactor banks are not sufficient because of their slow response time, a static var compensator (SVC) was installed on the Goto Islands. In such an application, an SVC control method should be developed so as not to override the existing voltage control systems. This paper describes the SVC control method developed for the Goto Islands AC interconnection project, which can be applied to similar situations. The effectiveness of the control method was verified by the results of effective value simulation and of field testing, which was implemented before the SVC was commissioned in 2007. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(3): 19–30, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22337     

Characteristics of the Arc Voltage of a High‐Current Air Arc in a Sealed Chamber

The effect of the arc voltage on various factors of design and control was investigated for high currents in order to develop design guidelines for circuit breakers. In this study, the dependence on such factors, namely, the current, arc length, electrode surface area, and internal pressure of the arc voltage, was evaluated quantitatively. As a result of the evaluations, it was estimated that the arc voltage near the electrode surface rises linearly with the arc current and the power ?0.8 of the surface area, and that the voltage in the arc column rises as the 0.3 power of the pressure increase. We confirmed the validity of the estimated voltage characteristics by comparison with the generated voltage in an actual arc‐extinction chamber. The characteristics of the estimated voltage can provide effective guidelines for the design of arc extinguishing chambers. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(1): 34–42, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22487     

Development of Motor Model of Rotor Slot Harmonics for Speed Sensorless Control of Induction Motor

This paper proposes a novel mathematical dynamic model to represent the steady‐state and transient‐state characteristics of rotor slot harmonics of an induction motor for sensorless control. Although it is well known that the rotor slot harmonics originate from the mechanical structure of the induction motor, a mathematical model that describes the relationship between the stator/rotor currents of the induction motor and the slot harmonics has not yet been proposed. Therefore, in this paper, a three‐phase model of the induction motor that depicts the rotor slot harmonics is developed by taking into consideration the magnetomotive force harmonics and the change in the magnetic air gap caused by the rotor slots. The validity of the proposed model is verified by comparing the experimental results and the calculated values. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(3): 63–74, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22478     

Focal calcium monitoring with targeted nanosensors at the cytosolic side of endoplasmic reticulum

Ca²⁺ distribution is spatially and temporally non-uniform inside cells due to cellular compartmentalization. However, Ca²⁺ sensing with small organic dyes, such as fura-2 and fluo-4, has been practically applied at a single cell level where the averaged signal from freely diffusing dye molecules is acquired. In this study, we aimed to target azide-functionalized fura-2 (N₃-fura-2) to a specific site of subcellular compartments to realize focal Ca²⁺ sensing. Using scAVD (single-chain avidin)–biotin interaction and a copper-free click reaction system, we linked N₃-fura-2 to specifically-targeted scAVD protein fused with a red fluorescent protein mCherry, so that Ca²⁺ sensors conjugated with four N₃-fura-2 dyes with dibenzocyclooctyne (DBCO)-PEG4-biotin as a linker were generated at subcellular compartments in living cells. In cytoplasm, N₃-fura-2 showed a prolonged retention period after binding to scAVD. Furthermore, the reacted N₃-fura-2 was retained inside cells even after free dyes were washed out by methanol fixation. When scAVD was overexpressed on endoplasmic reticulum (ER) membranes, N₃-fura-2 was accumulated on ER membranes. Upon histamine stimulation, which increases cytosolic Ca²⁺ concentration, ER-localized N₃-fura-2 successfully sensed the Ca²⁺ level changes at the cytosolic side of ER membrane. Our study demonstrated specific targeting of N₃-fura-2 to subcellular compartments and the ability of sensing focal Ca²⁺ level changes with the specifically targeted Ca²⁺ sensors.     

Present Status of the Nd:YAG Thomson Scattering System Development for Time Evolution Measurement of Plasma Profile on Heliotron J

A new high repetition rate Nd:YAG Thomson scattering system is developed for the Heliotron J helical device.A main purpose of installing the new system is the temporal evolution measurement of a plasma profile for improved confinement physics such as the edge transport barrier (H-mode) or the internal transport barrier of the helical plasma.The system has 25 spatial points with ～10mm resolution.Two high repetition Nd:YAG lasers (>550mJ@ 50Hz) realize the measurement of the time evolution of the plasma profile with ～10ms time intervals.Scattered light is collected by a large concave mirror (D=800 mm,f/2.25) with a solid angle of ～100 mstr and transferred to interference filter polychromators by optical fiber bundles in a staircase form.The signal is amplified by newly designed fast preamplifiers with DC and AC output,which reduces the low frequency background noise.The signals are digitized with a multi-event QDC,fast gated integrators.The data acquisition is performed by a VME-based system operated by the CINOS.     

Evaluation of Young’s modulus of imprinted hydrogen silsesquioxane pillar after residual layer removal by reactive ion etching

Nanoimprint lithography has two basic steps. The first is the imprint step in which a mold with nanostructures on its surface is pressed into a resin film on a substrate, followed by removal of the mold. The second step is the residual layer removal by a reactive ion etching (RIE). There is no report whether the properties of the imprinted structure after RIE change or not. In this work, the authors evaluated the Young’s modulus of the imprinted pillar after residual layer removal by RIE. In this experiment, hydrogen silsesquioxane (HSQ), a type of spin-on-glass, was used as an imprint material. The residual layer was etched by RIE using CHF₃ gas. The Young’s modulus of imprinted pillar after RIE was measured via cantilever method. The Young’s modulus of HSQ pillar after RIE was twice as much as that of HSQ pillar before RIE. From the Fourier transform infrared measurement, it was founds the chemical structure of HSQ was changed by forming network structure due to heating by RIE plasma energy. These results indicate that the mechanical property of imprinted structure was changed in the residual layer removal step by using RIE.