Present Status of the Nd:YAG Thomson Scattering System Development for Time Evolution Measurement of Plasma Profile on Heliotron J

A new high repetition rate Nd:YAG Thomson scattering system is developed for the Heliotron J helical device.A main purpose of installing the new system is the temporal evolution measurement of a plasma profile for improved confinement physics such as the edge transport barrier (H-mode) or the internal transport barrier of the helical plasma.The system has 25 spatial points with ～10mm resolution.Two high repetition Nd:YAG lasers (>550mJ@ 50Hz) realize the measurement of the time evolution of the plasma profile with ～10ms time intervals.Scattered light is collected by a large concave mirror (D=800 mm,f/2.25) with a solid angle of ～100 mstr and transferred to interference filter polychromators by optical fiber bundles in a staircase form.The signal is amplified by newly designed fast preamplifiers with DC and AC output,which reduces the low frequency background noise.The signals are digitized with a multi-event QDC,fast gated integrators.The data acquisition is performed by a VME-based system operated by the CINOS.     

Development of a Compact-Sized Falling Needle Rheometer for Measurement of Flow Properties of Fresh Human Blood

A compact-sized falling needle rheometer with rapid operation and automatic flow analysis has been developed for viscometry of fresh human blood without anticoagulant. The volume of a fresh blood sample only needs to be 3 mL, and the measuring time is within 2 min after taking a blood sample from the human body. Measured flow properties of human blood are evaluated as a flow curve, that is, the relationship between the shear stress (τ) and shear rate (γ). Observed flow curves of fresh human blood show three typical fluid regions, that is, the Casson fluid region for a low shear rate range of 0 < γ > 140 s^?1, the transition region for a shear rate near 140 s^?1 < γ < 160 s^?1, and the Newtonian fluid region for a high shear rate range of 160 s^?1 < γ > 400 s^?1. Flow properties of human blood such as the yield stress (τ _y) in the Casson fluid region and the apparent viscosity (μ) in the Newtonian fluid region are measured, and they are compared between male and female blood. It is found that the range of human blood viscosity for males is (5.5 to 6.4) mPa · s, and for females is (4.5 to 5.3) mPa · s. The viscosities of male blood without anticoagulant show higher values than those of female blood. Human blood viscosities with anticoagulant show a lower value than that without anticoagulant. A linear relationship between the hematocrit value, that is, the volume percentage of red corpuscles in the human blood, and the apparent viscosity are observed for both male and female blood. This article is concerned with the flow analysis of fresh human blood viscosity without anticoagulant using a newly developed compact-sized falling needle rheometer.     

Synthesis and Properties of Gemini-type Cationic Surfactants Containing Carbonate Linkages in the Linker Moiety Directed Toward Green and Sustainable Chemistry

Gemini-type cationic surfactants containing carbonate linkages as biodegradable and chemically recyclable segments, consisting of two long-chain alkyl groups, two quaternary ammonium groups and a linker moiety, were designed and synthesized as novel green and sustainable cationics with improved physicochemical and biological activities. The gemini-type cationics containing a carbonate linkage showed lower critical micelle concentration values compared to the corresponding single-type cationics. Also, the gemini-type cationics containing a carbonate linkage in the linker moiety showed strong antimicrobial activities. The biodegradability of the gemini-type cationics was significantly improved when a carbonate linkage was introduced into the linker moiety. The maximum biochemical oxygen demand-biodegradability of the gemini-type cationics containing a carbonate linkage in the linker moiety exceeded 70% after a 28-day incubation. Furthermore, the gemini-type cationics containing both a carbonate linkage and an n-dodecyl group showed a chemical recyclability using a lipase (E.C. 3.1.1.3).

Structural development and mechanical properties on immiscible and miscible blends from isotactic polypropylene and ethylene-1-hexene copolymers under uniaxial drawing

Isotactic polypropylene and ethylene-1-hexene copolymers containing 32 and 57 mol% of 1-hexene copolymers blends (i-PP/EH32 and i-PP/EH57) were prepared by solution blending, precipitating followed by drying and hot pressing. The two blends were subject to investigation on structure and mechanical properties of these blends under uniaxial drawing. The i-PP/EH32 and i-PP/EH57 represented the immiscible and miscible blends, respectively. The tensile stresses and strains at breaking point of i-PP/EH57 were remarkably higher than those of i-PP/EH32 at room temperature. From wide-angle X-ray diffraction (WAXD) measurement, it was observed that the orientation of crystallites occurred early and then propagated gradually up to about drawing ratio 8 because chains of EH57 copolymer were incorporated into the amorphous regions between lamellae of i-PP. In the WAXD patterns of i-PP/EH57, the oriented spot reflections coexsisted with unoriented ring reflections up to draw ratio higher than in pure i-PP. On the other hand, the two-phase structure was observed from TEM and AFM in i-PP/EH32, and on the drawing, separation at the interface between two-phase was observed in i-PP/EH32 even at the low strain.     

Structural development of natural rubber during uniaxial stretching by in situ wide angle X-ray diffraction using a synchrotron radiation

Structural development of natural rubber during uniaxial stretching was examined by an in situ wide angle X-ray diffraction measurement using a synchrotron. During stretching, the amorphous part showed little change, i.e. an amorphous halo remained clear even at 500% strain. The fraction of induced crystals was very small, though a clear crystalline pattern was observed at 400% strain. Some polymer chains were oriented and crystallized, but most of the chains were not oriented at all in spite of large deformations of the specimen. Only a small amount of polymer chains contributes to the stress and hysteresis loss during elongation.     

Biodegradable polylactide/montmorillonite nanocomposites

Our continuing research on the preparation, characterization, materials properties, and biodegradability of polylactide (PLA)/organically modified layered silicate (OMLS) nanocomposites has yielded results on PLA/montmorillonite nanocomposites. Montmorillonite (mmt) modified with dimethyldioctadecylammonium cation was used as an OMLS for nanocomposite preparation. The internal structure of nanocomposites on the nanometer scale was established with the use of wide-angle X-ray diffraction patterns and transmission electron micrographic observation. All nanocomposites exhibited significant improvement in crystallization behavior, mechanical properties, flexural properties, heat distortion temperature, and O2 gas permeability when compared with pure PLA.     

A series of modeling of plasma etching and damage reduction: vertically integrated computer aided design for device processing

The present stage of a series of numerical modelings of the plasma etching processes is overviewed. Physical, chemical and electrical linkage among modules describing low-temperature plasma structure/function in a reactor, the profile and local charging evolution in a hole/ trench, and electrical device damage during etching will make it possible to preparea technology computer aided design (TCAD) for the practical purpose of prediction and design of the etching process. This system will also help us to determine device arrangement and size in the system on a chip (SoC) in a closed integration system. Vertically integrated CAD for device processing (VicAddress) has been recently proposed by the authors. VicAddress will also provide a tool for discussing the etching processes between process engineers and device designers in the age of nanometer-scale device technology.