加油站设置发电机组问题的探讨

针对有些加油站在采用外接电源的同时配备发电机组存在的诸如使加油站安全要求提高、设备投入费用增加、运营管理成本增加、发电机组使用效率低和安全隐患增加等问题，建议本着经济的原则，在缺电少电比较严重的地区或引用外接电源有困难的加油站可另外设置发电机组，对遇偶然性停电的加油站，应采用在市场上临时租赁移动发动机业务或由公司组建自己的移动式发电机组服务部门，以保证加油站应急用电需求。     

TD-SCDMA技术及市场分析

TD-SCDMA技术优势 2000年5月,在土耳其伊斯坦布尔召开的国际电联大会上,TD-SCDMA被国际电联接纳为第三代移动通信系统标准之一,这标志着中国在移动通信技术领域已经进入世界先进行列.     

镜质体反射率与砂岩孔隙度关系的研究与应用

利用有关孔隙度和有机质热成熟度的理论公式研究了二者之间的内在联系 ,建立起Ro与砂岩孔隙度之间的关系模型。用该模型对济阳坳陷沾化凹陷渤南洼陷沙河街组四段上亚段烃源层有机质的成熟度进行了估算 ,指出该烃源层有机质已达到成熟     

减少地下工程支护喷射混凝土回弹量的措施

介绍了水布垭地下厂房喷射混凝土室内试验结果和施工实践,总结了降低喷射混凝土回弹率的主要措施。     

Mitigation of polarization-mode dispersion in multichannel lightwave transmission systems

We propose a novel polarization-mode dispersion (PMD) compensation scheme for wavelength-division-multiplexing (WDM) systems, in which many WDM channels share one or a few PMD compensators at receiver site. It is shown, both analytically and numerically, that this scheme can achieve virtually the same performance as that using per-channel-based PMD compensation.     

Vibration thresholds for fretting corrosion in electrical connectors

Single frequency vibration tests were used to induce fretting corrosion in tin alloy plated contacts. The samples used in this study were connectors consisting of 25 pairs of mated pin and socket contacts. Experimental results for a variety of vibration levels, frequencies, and wiring tie-off lengths are presented. The experiments consisted of running a series of vibration tests at each frequency where the excitation level was stepped through a range of g-levels. During each test run contact resistance was monitored as a performance characteristic. The results exhibit threshold behavior at each frequency for the onset of fretting degradation. Typically a plateau region was observed where similar g-levels produced similar fretting rates. It was also found that outside the plateau region the g-levels varied according to the dynamic behavior of the mechanical system. In addition, a transfer matrix model was used to analyze these results. An empirical fit of the data correlated well with the model when damping was used. This analysis revealed the importance of the bending moment induced at the contact interface as a result of excitation levels and tie-off configurations. Consequently, it is concluded that dynamic response of the mechanical system under various g-levels and tie off configurations can greatly impact the performance of a connector system subjected to vibration stresses.     

离子束混合工艺对材料抗蚀性能的影响

本文介绍了离子束混合工艺方法。与直接注入相比较,离子束混合所使用的设备造价低1/4—1/2,而生产效率可提高1—2个数量级,因而使生产成本大幅度降低,这无疑对离子束工艺的实际应用将产生巨大的促进作用。 通过对轴承材料(GCr15和Cr4Mo4V)经Cr、N、Ta不同元素的混合处理后,在0.5M H_2SO_4和0.1M NaCl的缓冲溶液中的阳极极化曲线表明经混合处理后的两种材料试样,其抗蚀能力和抗点蚀能力均大大提高,这与直接注入的试样效果是一致的。 通过俄歇谱仪和透射电镜的分析结果表明混合是成功的,且在一定的条件下,形成非晶组织。 本文的结论是,无论是离子的直接注入还是离子束混合,对提高轴承材料的抗腐蚀性能都是有效的方法,特别是离子束混合技术具有更大的应用前景。     

Ф16mm、Ф18mm钼棒的研制

采用等静压制法，压制钼圆棒坯，经中频高温烧结，制得尺寸适合、用户满意的钼电极棒。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

化学束外延

本文介绍了化学束外延(CBE)的发明和发展,论述了CBE的原理和设备。文中还介绍了最近提出的一种生长机理。