不同孔形下豆类透筛效果对比及圆筒筛优化

以大豆为对象,推导了筛孔透筛区域的面积计算公式,对比了不同孔型圆筒筛的大豆透筛效果,得出大豆在正方形筛孔的圆筒筛中透筛效果最好,并通过仿真计算对其进行了验证。在此基础上对正方形筛孔的圆筒筛进行优化,用筛分比和除杂比计算筛分效果,通过正交仿真试验分析得到不同工艺参数对圆筒筛的豆类筛分效果的影响次序,并得出最佳工艺参数为圆筒倾角5°、圆筒转速16r/min、进料速度14t/h、筛孔边长9mm,该条件下筛分效果为0.935,比原始模型提高了3.89%。     

On Cost Aware Cloudlet Placement for Mobile Edge Computing

As accessing computing resources from the remote cloud inherently incurs high end-to-end (E2E) delay for mobile users, cloudlets, which are deployed at the edge of a network, can potentially mitigate this problem. Although some research works focus on allocating workloads among cloudlets, the cloudlet placement aiming to minimize the deployment cost (i.e., consisting of both the cloudlet cost and average E2E delay cost) has not been addressed effectively so far. The locations and number of cloudlets have a crucial impact on both the cloudlet cost in the network and average E2E delay of users. Therefore, in this paper, we propose the Cost Aware cloudlet PlAcement in moBiLe Edge computing (CAPABLE) strategy, where both the cloudlet cost and average E2E delay are considered in the cloudlet placement. To solve this problem, a Lagrangian heuristic algorithm is developed to achieve the suboptimal solution. After cloudlets are placed in the network, we also design a workload allocation scheme to minimize the E2E delay between users and their cloudlets by considering the user mobility. The performance of CAPABLE has been validated by extensive simulations.      

Role of Co in formation of Ni-Ti clusters in maraging stainless steel

The effect of Co addition on the formation of Ni-Ti clusters in maraging stainless steel was studied by three dimensional atom probe (3DAP) and first-principles calculation. The cluster analysis based on the maximum separation approach showed an increase in size but a decrease in density of Ni-Ti clusters with increasing the Co content. The first-principles calculation indicated weaker Co-Ni (Co-Ti) interactions than Co-Ti (Fe-Ti) interactions, which should be the essential reason for the change of distribution characteristics of Ni-Ti clusters in bcc Fe caused by Co addition.     

王瑶水库加坝扩容工程筑坝土料分散性研究

土料分散性是筑坝土性质量关键性指标之一,影响着大坝工程长久安全使用,关注其特性及其物化特点是指导工程设计合理选择处理方案的重要依据。通过对土料基本物性试验,结合采用双比重计试验、碎块试验、针孔试验等方法研究土料的分散特性,得出一般黄土料用不同试验方法其分散性具有多样性成果,需采用合理方法予以评判,旨在对分布广泛的黄土中代表王瑶水库筑坝土料进行分析评价,以便为今后工程中判定利用此区风积黄土有一定的现实意义。     

Structural,morphological, dielectric and magnetic properties of Zn-Zr co-doping yttrium iron garnet

In this study, yttrium iron garnet co-doped with Zn and Zr atoms with a chemical formula Y₃Zn_xZr_xFe_(5−2x)O₁₂ (x = 0.0-0.3) has been successfully prepared by the solid-state reaction method. The effects of doping concentration on the microstructure, crystal structure, magnetic properties, and dielectric properties of Y₃Zn_xZr_xFe_(5−2x)O₁₂ were investigated. The microstructure analysis indicates that co-doping of YIG with Zn and Zr can effectively reduce the grain size of the ceramic. The crystal structure results reveal that the doping concentration of Zn–Zr has substantial influence on the lattice parameters of YIG, such as, increases the lattice constant, crystal cell size, and interplanar spacing. However, the second phase of ZrO₂ appears once x ≥ 0.15. Additionally, the dielectric properties of YIG ferrite can be regulated using this Zn–Zr co-doping method. Zn–Zr co-doping can improve the dielectric stability and reduce the dielectric loss at high temperature. The magnetization measurement shows that the saturation magnetization is stabilized at x < 0.15, and the magnetic loss is decreased with the increase in the doping concentration. Overall, the findings show that the ceramic with x = 0.1 exhibits better properties included high saturation magnetization (24.607 emu/g), low magnetic loss (0.0025 @ 1 MHz), and relatively low dielectric loss (496 @ 400°C).     

基于图像增强的去雾快速算法的FPGA实现

基于图像增强方法，本文提出了一种使用亮度映射的图像去雾快速算法。此算法通过调整室外多雾场景图像的对比度，提高了雾中物体的辨识度。算法的复杂度低、处理延迟小，实时性高，利于FPGA的实现。实现时不需外存储器，延时为ns级，并提供了强度调节接口，以适应较广的应用环境。     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

Dandelion-Like Bi2S3/rGO hierarchical microspheres as high-performance anodes for potassium-ion and half/full sodium-ion batteries

Sodium-ion batteries (SIBs) and potassium-ion batteries (PIBs) have been considered as attractive alternatives for next-generation battery systems, which have promising application potential due to their earth abundance of potassium and sodium, high capacity and suitable working potential, however, the design and application of bi-functional high-performance anode still remain a great challenge up to date. Bismuth sulfide is suitable as anode owing to its unique laminar structure with relatively large interlayer distance to accommodate larger radius ions, high theoretical capacity and high volumetric capacity etc. In this study, dandelion-like Bi₂S₃/rGO hierarchical microspheres as anode material for PIBs displayed reversible capacity, and 206.91 mAh·g⁻¹ could be remained after 1,200 cycles at a current density of 100 mA·g⁻¹. When applied as anode materials for SIBs, 300 mAh·g⁻¹ could be retained after 300 cycles at 2 A·g⁻¹ and its initial Coulombic efficiency is as high as 97.43%. Even at high current density of 10 A·g⁻¹, 120.3 mAh·g⁻¹ could be preserved after 3,400 cycles. The Na₃V₂(PO₄)₃@rGO//Bi₂S₃/rGO sodium ion full cells were successfully assembled which displays stable performance after 60 cycles at 100 mA·g⁻¹. The above results demonstrate that Bi₂S₃/rGO has application potential as high performance bi-functional anode for PIBs and SIBs.

     

Effect of ultrasonic vibration on thermal and material flow behavior,microstructure and mechanical properties of friction stir welded Al/Cu joints

Al/Cu dissimilar joint has been widely produced by using friction stir welding (FSW), but the weld quality remains limited. A recently developed ultrasonic