基于图像增强的去雾快速算法的FPGA实现

基于图像增强方法，本文提出了一种使用亮度映射的图像去雾快速算法。此算法通过调整室外多雾场景图像的对比度，提高了雾中物体的辨识度。算法的复杂度低、处理延迟小，实时性高，利于FPGA的实现。实现时不需外存储器，延时为ns级，并提供了强度调节接口，以适应较广的应用环境。     

基于萤石溶解/表面转化的含钙矿物表面定向调控浮选技术及机理研究

研究了萤石在白钨矿和方解石表面溶解和转化的可能性, 发现萤石可以在特定的捕收剂体系下作为抑制剂实现含钙矿物的浮选分离。浮选实验结果表明, 萤石作为抑制剂, 在白钨矿和方解石的浮选中, 用量小、作用效果明显; 动电位检测结果证实了萤石能明显降低方解石的动电位, 但对白钨矿基本没有影响; XPS检测结果证明了萤石对方解石的作用主要在于对Ca-O键能的减弱和Ca-F基团的生成, 即在方解石表面生成CaF2膜; AFM检测则可直观观察到方解石表面经过萤石处理之后出现明显的起伏, 印证了离子的侵蚀与CaF₂膜的生成。     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.     

Formation of a protective layer against corrosion on Mg alloy via alkali pretreatment followed by vanillic acid treatment

Although Mg alloy possesses high specific strength, low density, and good biocompatibility, poor corrosion resistance hinders its further applications. In the present study, an innovative protective layer against corrosion was prepared on the AZ31 Mg alloy via alkali pretreatment followed by vanillic acid treatment. The alkali pretreatment supplied –OH for the AZ31 Mg alloy surface to react with vanillic acid. The vanillic acid treatment played a crucial role in enhancing the corrosion resistance due to the excellent ability to act as a barrier and retard aqueous solution penetration, which effectively isolated the underlying Mg alloy from the corrosive environment. The corrosion current density of alkali and vanillic acid-treated Mg alloy (AZ31V) almost showed two orders of magnitude lower values in comparison with that of the AZ31 Mg alloy, and the corrosion potential of AZ31V Mg alloy increased from −1.41 to −1.25 V. The immersion tests proved that there was no occurrence of severe corrosion. Hence, the alkali pretreatment and vanillic acid treatment may represent a promising method to improve the corrosion resistance of Mg alloy.     

链轨节用钢15B36Cr的开发与试制

淮钢采用90 t顶底复吹转炉-LF-RH-200 mm×200 mm连铸-连轧工艺流程试生产了2炉Φ60 mm链轨节用钢15B36Cr(/%:0.30～0.37C、0.15～0.30Si、1.20～1.50Mn、≤0.040P、≤0.0505、0.20～0.40Cr、≤0.25Ni、≤0.35Cu、≤0.06Mo、0.0005～0. 0030B)。通过加严影响淬透性化学成分,控制出钢碳≥0.08%,转炉有效挡渣和下渣检测系统控制下渣,LF炉铝粒和电石渣面脱氧,RH最低真空度处理20～30 min,结晶器电磁搅拌、末端电磁搅拌和连铸低过热度保护浇铸等工艺措施,15B36Cr钢的化学成分稳定控制在内控范围内,除了B粗以外,其他类型非金属夹杂物级别全部控制在1.0以内,淬透性控制在较窄的范围内,试制钢种关键技术指标达到客户和预期设计要求。     

便携式飞行时间质谱仪的研制及其在石化污水系统挥发性有机物监测中的应用

近年来，国内的大气污染问题越来越严重，挥发性有机物（VOCs）的排放是其中一个重要原因。VOCs是臭氧和气溶胶的前驱物之一，在大气化学反应过程中扮演着极其重要的角色。本实验自行研制了一台基于真空紫外（VUV）灯的高分辨光电离飞行时间质谱仪（TOF MS），建立了一种新的VOCs稀释采样方法，并将其应用于石化行业污水处理系统VOCs的采样与分析。结果表明：隔油系统的3个池子基本没有测到高浓度的挥发性有机物，其中溶气气浮甲苯物质的质量浓度最高，为50.41 mg/L，其余组分的质量浓度大多数在0.1~1.0 mg/L之间；1#加氢和2#加氢隔油池有着类似的组分浓度，以1#加氢隔油池为例，二甲苯物质的质量浓度为10.60 mg/L，乙苯为52.33 mg/L，苯为59.80 mg/L；由于罐区隔油池没有加盖，处于露天状态，挥发性有机物气体容易向大气中扩散，并没有检测出较高浓度组分。可以看出，新式采样方法可有效地稀释定量样品，操作简便，减少了样品因闪蒸过程造成的VOCs损失，检出物质更丰富；同时，使用自行研制的TOF MS仪器能够快速检测不同装置污水处理系统的VOCs种类，将该仪器用于实际样品检测，发现化工企业大多数密闭的池子都含有苯系物、醚类等，但不同工艺的污水处理系统VOCs存在明显差异。该质谱仪适用于石化企业污水系统VOCs监测。     

基于改进NSGA-Ⅱ算法的乙烯裂解炉操作优化

现有的乙烯裂解炉优化通常只针对两个目标函数即产物乙烯和丙烯的收率，并且采用遗传算法的收敛效果一般，故提出一种基于改进NSGA-Ⅱ算法来研究一个多目标运行的解决方案，以此来解决乙烯裂解炉的固定周期操作优化问题，即在增大产物乙烯和丙烯收率的同时减少原料以及蒸汽流量来提高整体运行状况。把具体问题量化为数学模型，分析了原料气烃比、原料流量、出口温度对乙烯和丙烯收率的影响。实验结果表明，相较于原有操作条件，提出的优化方案具有良好的可行性。