Iodine reaction of vinyl acetate/vinyl propionate copolymers. III. Iodine affinities of the radically polymerized copolymers and the copolymers derived from partially saponified polyvinyl acetate

The minimum sequence lengths (n_c) of vinyl acetate (VAc) units necessary to form a colored iodine complex were determined to be 4 and 17 for radically polymerized VAc/vinyl propionate (VPr) and VAc/isopropenyl acetate (IPAc) copolymers, respectively. The iodine affinities (I/VAc) of VAc/VPr copolymers (SP-series) obtained by propionylation of partially saponified polyvinyl acetate (PVAc) were remarkably affected by the saponification conditions. An increase of the water content in acetone/water mixture as saponification solvent brought about a decrease of the iodine affinities of the SP-series. The dependence of the iodine affinity on the saponification of monomer units in the SP-series was compared with that in the radically polymerized VAc/VPr copolymers by taking the sequence probability as the measure of monomer unit distribution. The results strongly supported an occurence of the slide fastener reaction at high degrees of saponification, which was well-known in the saponification of PVAc. Furthermore, it was found that the saponification mode of PVAc at low degrees of saponification was influenced uniquely by the water content in saponification solvents and the saponification temperature.     

Graft copolymerization of styrene onto cellulose acetate p-nitrobenzoate by chain transfer reaction

Styrene was grafted onto cellulose acetate p-nitrobenzoate (CANB) by chain transfer reaction of growing polymer radicals to the pendant nitro groups of CANB. A copolymer with a branch for every 17.2 nitro groups was obtained. This result indicates that the pendant aromatic nitro group is more effective in obtaining a graft copolymer by radical mechanism than pendant double bond on the trunk polymer previously reported, where graft copolymers with a branch for several hundred of double bonds are produced.     

Radiation-induced graft copolymerization of mixtures of styrene and n-butyl acrylate onto cellulose and cellulose triacetate

Mixtures of styrene and n-butyl acrylate of various compositions were grafted onto cellulose and cellulose triacetate fibers preirradiated with γ-rays at 0°C in air. Monomer reactivity ratios of the grafted copolymers were found to be different from those of the nongrafted copolymers or those of AIBN-initiated copolymers. The active species initiating the graft copolymerization were trapped radicals for cellulose and peroxides for cellulose triacetate. Kinetic investigations of the graft copolymerization of styrene onto preirradiated cellulose triacetate fibers were also carried out, and it was found that the kinetic scheme for radical polymerization is also applicable to graft copolymerization in a heterogeneous system.     

Mechanical properties of DLC films prepared inside of micro-holes by pulse plasma CVD

Diamond-like carbon (DLC) films are metastable amorphous carbon materials with superior tribological characteristics. In order to improve wear resistance of micro-extrusion dies with numerous imperceptible holes, DLC films were deposited on the inner wall surface of model dies with holes of 2 and 0.9 mm in diameter, and 20 mm in depth by using pulse plasma CVD method. This paper will discuss how argon gas, deposition pressure and time affect the characteristics of films deposited on the inner wall surface of dies. This micro-coating method can be applied widely for inner wall surface treatment of components with thin holes.     

Effect of reaction kinetics of polymer electrolyte on the ion‐conductive behavior for poly(oligo oxyethylene methacrylate)–LiTFSI mixtures

The effect of the reaction kinetics on the ionic conductivity for a comblike‐type polyether (MEO) electrolyte with lithium bis(trifluoromethane sulfonyl)imide (LiTFSI) was characterized by DSC, complex impedance measurements, and ¹H pulse NMR spectroscopy. The ionic conductivity of these electrolytes was affected by the reaction condition of the methacrylate monomer and revealed by the glass transition temperature (T_g), spin–spin relaxation time (T₂), steric effects of the terminal groups, and the number of charge carriers indicated by the VTF kinetic parameter. In this system, the electrolytes prepared by the reaction heating rate of 10°C/min of MEO–H and 15°C/min of MEO–CH₃ showed maximum ionic conductivity, σ_i, two to three times higher in magnitude than that of the σ_i of the others at room temperature. As experimental results, the reaction kinetic rate affected the degree of conversion, the ionic conductivity, and the relaxation behaviors of polyether electrolytes. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2149–2156, 2003     

Development of a high‐resolution RGBW flexible display using a white organic light‐emitting diode with microcavity structure and that of a side‐roll touch panel

In this study, white organic electroluminescent devices with microcavity structures were developed. A flexible high‐resolution active‐matrix organic light‐emitting diode display with low power consumption using red, green, blue, and white sub‐pixels formed by a color‐filter method was fabricated. In addition, a side‐roll touch display was developed in combination with a capacitive flexible touch screen.     

High-strength–high-modulus polyimide fibers II. Spinning and properties of fibers

The polyimides based on 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) described in Part I of this series were dissolved in p-chlorophenol and spun into fibers using a coagulating bath of ethanol. The fibers as spun had in general low tenacities and low moduli, but a heat treatment at 300–500°C under tension produced a remarkable increase in strength and modulus, and fibers with a tensile strength of 26 g/den (3.1 GPa) and an initial modulus higher than 1,000 g/den (120 GPa) could be obtained. Thus, the annealed fibers of polyimides are comparable to aramid fibers in mechanical properties. To heating in air and in the saturated steam, the polyimide fibers showed higher resistance than the aramid fibers. The polyimide fibers surpassed the aramid fibers in resistance to acid treatment and ultraviolet (UV) irradiation, but were inferior in resistance to alkali treatment. The annealed fibers of polyimides displayed distinct X-ray diffraction patterns. The chain repeat distance of 20.5 Å determined on the fibers of polyimide prepared from BPDA and o-tolidine, and 20.6 Å determined on the fibers of polyimide derived from BPDA and 3,4′-diaminodiphenyl ether are reasonable when the dimensions of monomeric units and the shapes of the molecular chains are considered. The X-ray reflections of both polyimide fibers were indexed satisfactorily on the basis of postulated unit cells.     

Toughening of cycloaliphatic epoxy resins by poly(ethylene phthalate) and related copolyesters

Poly(ethylene phthalate) (PEP) and poly(ethylene phthalate–co‐ethylene terephthalate) were used to improve the brittleness of the cycloaliphatic epoxy resin 3,4‐epoxycyclohexylmethyl 3,4‐epoxycyclohexane carboxylate (Celoxide 2021?), cured with methyl hexahydrophthalic anhydride. The aromatic polyesters used were soluble in the epoxy resin without solvents and effective as modifiers for toughening the cured epoxy resin. For example, the inclusion of 20 wt % PEP (MW, 7400) led to a 130% increase in the fracture toughness (K_IC) of the cured resin with no loss of mechanical and thermal properties. The toughening mechanism is discussed in terms of the morphological and dynamic viscoelastic behaviors of the modified epoxy resin system. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 388–399, 2002; DOI 10.1002/app.10363     

Electro-rheological effect and dynamic rheological properties of a blend composed of two liquid crystalline materials with different molecular weight

Electro-rheological (ER) effect of a blend composed of two liquid crystalline materials with different molecular weights is described in this article. The results indicated that ER effect of the blend was observed at the temperature range where each neat sample did not show ER effect. Furthermore, both storage modulus (G′) and loss modulus (G″) decreased drastically at the temperature range for the blend in dynamic viscoelastic measurements. We show that steady ER effect could be obtained by using a blend made up of two liquid crystalline components, whereas remarkable increment in shear stress was not observed for each component under applied electric field.