Influence of various surface treated silica nanoparticles on the electrochemical properties of SiO2/polyurethane nanocoatings

Various organosilane-treated SiO₂ nanoparticles were dispersed in a 2-pack polyurethane coating. The influence of surface modification and silica content on the electrochemical behaviour of the resultant nanocoatings was investigated. Electrochemical impedance spectroscopy (EIS) and open circuit potential (OCP) variations were examined. The surface chemistry of nanoparticles and its effect on the resultant nanocoating morphology were also studied utilising FTIR, and TEM analyses. The results reveal that the presence of more hydrophobic groups and longer-lengthed hydrophobic chains on the surface of nanoparticles, greatly improves the interfacial interactions at the polymer/filler interfaces resulting in a better corrosion performance.     

Evaluation of Microstructure and Mechanical Properties in Dissimilar Austenitic/Super Duplex Stainless Steel Joint

To study the effect of chemical composition on microstructural features and mechanical properties of dissimilar joints between super duplex and austenitic stainless steels, welding was attempted by gas tungsten arc welding process with a super duplex (ER2594) and an austenitic (ER309LMo) stainless steel filler metal. While the austenitic weld metal had vermicular delta ferrite within austenitic matrix, super duplex stainless steel was mainly comprised of allotriomorphic grain boundary and Widmanstätten side plate austenite morphologies in the ferrite matrix. Also the heat-affected zone of austenitic base metal comprised of large austenite grains with little amounts of ferrite, whereas a coarse-grained ferritic region was observed in the heat-affected zone of super duplex base metal. Although both welded joints showed acceptable mechanical properties, the hardness and impact strength of the weld metal produced using super duplex filler metal were found to be better than that obtained by austenitic filler metal.     

Inverse Identification of Thermal Properties of Charring Ablators

The modified Levenberg-Marquardt method is used for simultaneous estimation of decomposition kinetic coefficients and temperature-dependent thermophysical properties of charring ablators with a moving boundary over a wide temperature range. No prior information is used for the functional forms of the unknown thermal conductivity and specific heat. The procedure used differs from the traditional one in that it does not require prescribed time-dependent surface heat flux, recession rate, and pyrolysis gas mass flow rate. These time-dependent quantities may recover during an iterative procedure. The measured temperatures are simulated numerically by the Charring material ablation code, which accounts for unsteady ablation. The method can determine unknown parameters in an efficient manner with reasonable accuracy, without exact advance knowledge about the net surface heat flux, surface recession, and gas flux through the material.     

Control of Hybrid Active Power Filter Based on Switching Function Coefficients

A pulse width modulation (PWM)-based control method for a three-level, four-wire neutral point clamped (NPC) inverter employed in a hybrid active power filter (HAPF) is proposed in this paper. The control method is based on switching function coefficients (SFCs) for harmonic compensation. An interior loop is also proposed for control and balancing of the DC-link voltages. In the proposed control system, one carrier signal is employed in the PWM unit in order to simplify its hardware as compared with traditional PWMs. Based on Fourier decomposition technique, mathematical analysis of the proposed control method is also presented. To decrease the NPC inverter rated power, passive power filters (PPFs) are designed to eliminate fifth and seventh order harmonic currents and to compensate source reactive currents. The proposed control system is implemented by a digital signal processing (DSP) in a laboratory prototype. The experimental results confirmed the validity of the proposed control method in compensation of harmonic currents under non-linear conditions     

Structural Response of World Trade Center Buildings 1, 2 and 7 to Impact and Fire Damage

The National Institute of Standards and Technology (NIST) conducted an extensive investigation of the collapse of World Trade Center towers (WTC 1 and WTC 2) and the WTC 7 building. This paper describes the component, subsystem, and global analyses performed for the reconstruction of the structural response of WTC buildings 1, 2, and 7 to impact and fire damage. To illustrate the component and subsystem analyses, the approach taken for simulating the performance of concrete slabs and shear stud connectors in composite floors subject to fire conditions are presented, as well as steel floor framing connections for beams and girders. The development of the global models from the component and subsystem analyses is briefly described, including the sets of input data used to bound the probable conditions of impact and fire damage. The final analysis results that were used to develop the probable collapse hypotheses, and a comparison of the results against observed events, are presented for each building. A review of research activities focused on improving understanding of structural system response to multi-floor fires following the WTC disaster is also provided.     

Poly1‐hexene: New impact modifier in HIPS technology

Poly1‐hexene was prepared using a conventional heterogeneous Ziegler–Natta catalyst and its stereoregularity was characterized using ¹³C‐NMR analysis. New kind of high impact polystyrene (HIPS) was prepared by radical polymerization of styrene in the presence of different amounts of synthesized poly1‐hexene (PH) as impact modifier (HIPS/PH) and compared with conventional high impact polystyrene with polybutadiene (HIPS/PB) as rubber phase. Scanning electron microscopy (SEM) revealed that the dispersion of poly1‐hexene in polystyrene matrix was more uniform compared with it in HIPS/PB. The impact strength of HIPS/PH was 29–79% and 80–289% higher than that in HIPS/PB and neat polystyrene, respectively. FTIR was used to confirm more durability of HIPS/PH samples toward ozonation. To study the effect of rubber type and amount on the T_gs of polystyrene, differential scanning calorimetry was employed. Results obtained from TGA demonstrated higher thermal stability of HIPS/PH sample in comparison with conventional HIPS/PB one. Our obtained results suggest new high impact polystyrene that in all studied aspects has better performance than the conventional HIPS. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43882.     

Synthesis and architecture study of a reactive polybutadiene polyamine as a toughening agent for epoxy resin

In this study, a novel reactive toughener for the epoxy resin was developed and compared with traditional hydroxyl‐terminated polybutadiene (HTPB). For this purpose, the highly reactive aliphatic amine‐terminated polybutadiene (ATPB) was synthesized at ambient conditions by nucleophilic substitution amination. The characterizations of the product were provided by Fourier transform infrared and ¹H NMR spectroscopy. According to the mechanical test results, incorporation of ATPB into epoxy networks can significantly toughen the epoxy matrix. The addition of 10 phr ATPB increased the critical stress intensity factor (K_IC) and critical strain energy release rate (G_IC) of the epoxy from 0.85 to 2.16 MPa m^1/2 and from 0.38 to 3.02 kJ m^?2, respectively. Furthermore, unlike HTPB, the presence of the ATPB did not deteriorate the tensile strength of the matrix. The toughening and failure mechanisms were discussed based on the epoxy network morphological characteristics. The reduction in cross‐linking density and glass transition temperature of the epoxy system upon modification with liquid rubbers was confirmed by dynamic mechanical analysis. This article opens up the possibility of utilizing reactive flexible diamines with polybutadiene backbone as effective toughening agents for thermoset polymers. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44061.     

Using the Mass Method to Produce PVC/Clay Nanocomposite Foams: The Effect of Nano-clay and Foaming Conditions on Density and Cell size

Nanocomposite foams contain very fine cells because of the fillers in nano scale. Due to the limited size of the cells, the mechanical and physical properties of nanocomposite foams are improved compared to polymer foams. In this study PVC/clay nanocomposite foams containing various concentrations of nano-clay (1, 3 and 5 phr) were successfully prepared. The samples were placed under CO₂ gas pressure at 5 MPa, by immersing in glycerin bath at 60, 70, 80 °C and 20, 30, 40 s, respectively, to form foams. The density and the cell size as a factor of nano-clay content, foaming time and temperature were investigated using Archimedes method and scanning electron microscopy, respectively. The minimum density was obtained in the sample containing 1 phr nanoclay prepared at 80 °C and 40 s. The minimum cell size was related to the sample containing 5 phr nanoclay at 60 °C and 20 s.