Role of Nd-Ni on structural,spectral and dielectric properties of strontium-barium based nano-sized X-type ferrites

The influence of neodymium and nickel substitution on structural and dielectric parameters was investigated in strontium-barium X-type hexagonal ferrites having composition SrBaCu_2?xNi_xNd_yFe_28?yO₄₆ (x = 0, 0.2, 0.4, 0.6, 0.8, 1 and y = 0, 0.02, 0.04, 0.06, 0.08, 0.1). Sol-gel method was employed for synthesizing these hexagonal ferrites. The XRD plots of all studied materials which were annealed at 1250 °C show single phase characteristics. Lattice parameter ‘c’ increased as a consequence of larger radius of rare earth ion (Nd³⁺) as compared to (Fe³⁺), while lattice parameter ‘a’ showed very small variation. The cell volume was obtained in the range 2508.32–2523.75 (ų). The inclusion of Nd-Ni also affected X-ray density, bulk density and porosity. The FTIR spectroscopy indicated the particular absorption peaks of hexagonal ferrites and it was performed in the range of 500–700 cm^?1. On account of Nd-Ni doping, the dielectric constant, dielectric loss and AC-conductivity showed decreasing trend. The occupancy of Nd³⁺ ions at octahedral site impedes the valence alternation of Fe³⁺; therefore there was decrease in dielectric permittivity. Ac conductivity has been decreased from 9.14 to 6.49 (Ω cm)^?1 at frequency of 2.7 GHz. The Cole-Cole plots of synthesized materials noticeably revealed grain boundary contribution. The appearance of single semi-circle in impedance Cole-Cole graphs confirms the exceptional role of grain boundaries in the conduction process. The considerably lower dielectric parameters of investigated nano X-type ferrites propose their feasibility for high-frequency applications (phase shifters, dielectric resonators, stealth technology etc).     

Al2O3/Yttria‐Stabilized Zirconia Hollow‐Fiber Membrane Incorporated with Iron Oxide for Pb(II) Removal

Removal by absorptive ceramic membranes can simultaneously absorb and separate metal ions from water. Alumina/yttria‐stabilized zirconia (Al₂O₃/YSZ) hollow‐fiber membranes, fabricated using phase inversion and sintering process, were deposited with iron oxide by an in‐situ hydrothermal process. The results showed that α‐Fe₂O₃ was produced and incorporated across the membranes. A reduction in flux was recorded with the deposition of α‐Fe₂O_3. However, it improved the adsorption capacity for heavy metal adsorption. The adsorption‐separation test demonstrated that the optimized membrane is able to completely remove Pb(II) ions after two hours.     

Ballistic behavior of plain and reinforced concrete slabs under high velocity impact

This work presents a numerical simulation of ballistic penetration and high velocity impact behavior of plain and reinforced concrete slabs. In this paper, we focus on the comparison of the performance of the plain and reinforced concrete slabs of unconfined compressive strength 41 MPa under ballistic impact. The concrete slab has dimensions of 675 mm × 675 mm × 200 mm, and is meshed with 8-node hexahedron solid elements in the impact and outer zones. The ogive-nosed projectile is considered as rigid element that has a mass of 0.386 kg and a length of 152 mm. The applied velocities vary between 540 and 731 m/s. 6 mm of steel reinforcement bars were used in the reinforced concrete slabs. The constitutive material modeling of the concrete and steel reinforcement bars was performed using the Johnson-Holmquist-2 damage and the Johnson-Cook plasticity material models, respectively. The analysis was conducted using the commercial finite element package Abaqus/Explicit. Damage diameters and residual velocities obtained by the numerical model were compared with the experimental results and effect of steel reinforcement and projectile diameter were studies. The validation showed good agreement between the numerical and experimental results. The added steel reinforcements to the concrete samples were found efficient in terms of ballistic resistance comparing to the plain concrete sample.     

Surface structural and solar absorptance features of nitrate-based copper-cobalt oxides composite coatings: Experimental studies and molecular dynamic simulation

The copper and cobalt oxides composites coatings on aluminum substrates have been successfully synthesized via sol-gel method using nitrate-based sol precursors. The composites were characterized by X-ray Diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Field Emission Scanning Electron Microscopy (FESEM), Atomic Force Microscopy (AFM), and UV–Vis–NIR spectrophotometry. The sol-gel reactions were discussed and Molecular Dynamics (MD) simulation was integrated into the study to predict molecules assembly properties. The XRD analyses revealed that the CuO and the Co₃O₄ composites were formed after the annealing process with the average difference of the calculated lattice parameters compared to ICDDs was 1.17%. The surface electronic structure was mainly consisted of tetrahedral Cu(I), octahedral Cu(II), tetrahedral Co(II), octahedral Co(III) as well as surface, sub-surface and lattice oxygen O^?. The XRD, XPS and MD simulation results showed that there was minimal (or possibly non-existing) indication of copper-cobalt mixed phase oxides formations. FESEM and AFM surveys revealed that the coating had a porous surface composed of interlinked nanoparticles in the range of ~?10 to ~?40?nm. UV–Vis–NIR reflectance spectra showed that the sol precursors concentration and the dip-drying cycle significantly influenced the absorptance value with optimum absorptance (α) of 88.7% exhibited by coating synthesized using sol concentration of 0.1?M and 10 dip-drying cycles. High absorptance value and simplicity in the synthesis process render the coatings to be very promising candidates for solar selective absorber (SSA) applications.     

A Distributed Routing Method for Dynamic Multicasting

Single point, sender based control does not scale well for multicast delivery. For applications, such as group video or teleconferencing a low total cost multicast tree is required. In this article we present a destination driven algorithm to minimize the total tree cost of multicast tree in a dynamic situation for the whole session duration. In this heuristic approach we considered the staying duration of participants are available at the time of joining. The performance of our algorithm is analyzed through extensive simulation and evaluated against several other existing dynamic multicast routing and also against one well known near optimum heuristic algorithm used for solving Steiner tree problem. We have further tested our algorithm using erroneous information given by the joining participants. Simulation results show that its performance does not degrade that much even when the range of error is considerably high, which proves the robustness of our algorithm.     

Reconfigurable hardware implementation of a phase-correlation stereoalgorithm

This paper describes the implementation of a stereo-vision system using Field Programmable Gate Arrays (FPGAs). Reconfigurable hardware, including FPGAs, is an attractive platform for implementing vision algorithms due to its ability to exploit parallelism often found in these algorithms, and due to the speed with which applications can be developed as compared to hardware. The system outputs 8-bit, subpixel disparity estimates for 256× 360 pixel images at 30,fps. A local-weighted phase correlation algorithm for stereo disparity [Fleet, D. J.: {Int. Conf. Syst. Man Cybernetics 1:48–54 (1994)] is implemented. Despite the complexity of performing correlations on multiscale, multiorientation phase data, the system runs as much as 300 times faster in hardware than its software implementation. This paper describes the hardware platform used, the algorithm, and the issues encountered during its hardware implementation. Of particular interest is the implementation of multiscale, steerable filters, which are widely used in computer vision algorithms. Several trade-offs (reducing the number of filter orientations from three to two, using fixed-point computation, changing the location of one localized low-pass filter, and using L1 instead of L2 norms) were required to both fit the design into the available hardware and to achieve video-rate processing. Finally, results from the system are given both for synthetic data sets as well as several standard stereo-pair test images.     

Pegylated peptides. V. Carboxy-terminal PEGylated analogs of growth hormone-releasing factor (GRF) display enhanced duration of biological activity in vivo

In the present study, human growth hormone-releasing factor (hGRF) and analogs were successfully pegylated at the carboxy-terminus using a novel solid- and solution-phase strategy. Following synthesis, these pegylated hGRF analogs were evaluated for in vitro and in vivo biological activity. Specifically, hGRF (1-29)-NH2, [Ala15]-hGRF (1-29)-NH2, [desNH2Tyr1, D-Ala2, Ala15]-hGRF(1-29)-NH2 and [His1, Val2, Gln8, Ala15, Leu27]-hGRF(1-32)-OH were each C-terminally extended using a Gly-Gly-Cys-NH2 spacer (previously demonstrated not to alter intrinsic biological activity), and then monopegylated via coupling to an activated dithiopyridyl-PEG reagent. PEG moieties of 750, 2000, 5000 or 10,000 molecular weight (MW) were examined to determine the effect of polymer weight on activity. Initial biological evaluations in vitro revealed that all C-terminally pegylated hGRF analogs retained high growth hormone (GH)-releasing potencies, regardless of the MW of PEG polymer employed. Two of these pegylated hGRF analogs, [desNH2Tyr1, D-Ala2, Ala15]-hGRF (1-29)-Gly-Gly-Cys(NH2)-S-Nle-PEG5000 and [His1, Val2, Gln8, Ala15, Leu27]-hGRF(1-32)-Gly-Cys(NH2)-S-Nle-PEG5000, were subsequently evaluated in both pig and mouse models and found to be highly potent (in vivo potency range = 12-55-fold that of native hGRF). Relative to their non-pegylated counterparts, these two pegylated hGRF analogs exhibited enhanced duration of activity.