One‐Step Formulation of Protein Microparticles with Tailored Properties: Hard Templating at Soft Conditions

Formulation of therapeutic proteins into particulate forms is a main strategy for site‐specific and prolonged protein delivery as well as for protection against degradation. Precise control over protein particle size, dispersity, purity, as well as mild preparation conditions and minimal processing steps are highly desirable. It is, however, hard to fit all these criteria with conventional preparation techniques. Here a one‐step hard‐templating synthesis of microparticles composed of functional, non‐denatured protein is reported. The method is based on filling porous CaCO₃ microtemplates with the protein near to its isoelectric point (pI) followed by pH‐ or EDTA‐mediated dissolution of the tempplates. In principle, a wide variety of proteins can be converted into microparticles using this approach. The main requirement is an overlap of the protein insolubility and a template solubility for a certain parameter (here pH or EDTA). Here the formulation of insulin particles is studied in detail and it is shown that particles consisting of high molecular weight protein (catalase) can also be prepared. In this context, the synthesis of CaCO₃ templates with controlled size, the mechanism of the protein microparticle formation and mechanical properties of the microparticles are discussed. For the first time, the fabrication of mesoporous monodispersed CaCO₃ microtemplates with identical porocity but tuned diameter from 3 to 20 μm is demonstrated. The protein particle diameter can be adjusted by choosing the appropriate template size that is critical for successful pulmonary delivery of insulin. As a first step towards insulin delivery, the in vitro release of insulin at physiological conditions is studied.     

Assessment of noise attenuating powertrain components

Forschung im Ingenieurwesen - Wind turbine noise used to be dominated by aerodynamic blade noise, effectively masking mechanical noise, originating from the drivetrain. Successful blade noise...     

Exergy analysis of the diesel pre-reforming solid oxide fuel cell system with anode off-gas recycling in the SchIBZ project. Part I: Modeling and validation

Solid oxide fuel cell (SOFC) systems with anode off-gas recirculation (AGR) and diesel pre-reforming are advantageous because they can operate with the current fuel infrastructure. In the SchIBZ-project, the prototype of such a SOFC system for maritime applications has already been commissioned. In this first paper, we model the system devices to conduct an exergy analysis of this real SOFC plant and validate them with experimental values from experiments in laboratory scale. The results of our simulation agree well with the experimental values. The calculations with the validated results may be closer to the real thermodynamic behavior of such system components than previous literature.     

Synthesis of Janus polyaniline–polyelectrolyte complex membrane via in situ confined polymerization

Polyelectrolyte complex (PEC) membranes prepared from poly(styrene sulfonate) (PSS) and poly(diallyldimethylammonium chloride) (PDADMAC) were modified by crossflow polymerization of aniline (ANI). The PEC membranes were used as separators in a two-compartment setup where ANI monomer and ammonium persulfate (APS) oxidant diffused through the membranes to form polyaniline (PANI). APS and ANI having different distributions throughout the membranes, the reaction led to the asymmetric polymerization of PANI on one face of each PEC membrane thus producing Janus membranes. Due to the excess PANI content, the membrane displayed distinct asymmetric electrical conductivities on each face. Interestingly, very different ANI polymerizations were obtained when nonstoichiometric PEC membranes having different molar ratio of cationic and anionic polyelectrolytes (P⁺:P^? represents PDADMAC:PSS) were used and transport of APS was fastest through the 2:1 PEC when compared to the 1:2 PEC. In all experiments, the polymerization was most intense on the ANI side of the membranes. Also, the influence of NaCl both during PEC fabrication and during polymerization was studied and found to have some effect on the solute permeability. Results showed that a higher content of PANI was formed on PEC membranes having excess P⁺ and with no NaCl added during PEC fabrication. Although X-ray diffraction confirmed the presence of PANI on both sides of each membrane, scanning electron microscopy images demonstrated that both sides of each membrane had different PANI content deposited. Electrical conductivity measurements using a four-point probe setup also showed that the PEC–PANI exhibits asymmetric electrical property on different sides. © 2021 Society of Industrial Chemistry.     

Continuous generating grinding—Tooth root machining and use of CBN-tools

Profile accuracy, no burning and residual compressive stresses at the tooth root fillet are required for the durability of highly stressed gears. This paper reveals the challenges for continuous generating grinding with corundum and CBN. For this purpose, material removal simulations and experimental investigations were carried out to gain knowledge of the tool–workpiece contact conditions. The potential of CBN tools was analysed due to the fact that the mechanical loads at the grinding worm tip result in high profile wear of the corundum tools. In this context, especially the interrelationship between the dressing strategy and the workpiece quality was investigated in detail.