Application of the HeapSim model to the heap bioleaching of the Pueblo Viejo ore deposit

The HeapSim computer model can simulate column, crib, and heap leach processes for a variety of sulfide ores. In this work, the model was used to evaluate the feasibility of heap biooxidizing the high-grade pyrite ore from the Pueblo Viejo deposit in the Dominican Republic. Simulations have revealed few but critical conditions for the success of a full-scale heap.The heap should be inoculated with mesophiles and moderate thermophiles bacteria, as well as extreme thermophilic archaea at the start-up of the biooxidation pretreatment. These microorganisms were isolated from two slurry cultures collected at site and grown in the laboratory at different temperatures. All cell types may be indigenous to the site, but inoculation of the ore and leach solution with all cell types is necessary for the transition into different temperature regimes for best sulfide oxidation performance.To ensure that all parts of the heap achieve at least 65% sulfide oxidation in the planned 400 days of treatment, the heap height should be less than 8 m if aerated at 2 m³/m²/h and irrigated at 8 L/m²/h. These conditions would preclude the formation of “hot spots” that could inhibit even the extreme thermophiles. By increasing the aeration rate to 4 m³/m²/h and the irrigation rate to 11 L/m²/h, the heap could be stacked to 8 m. Large aeration and irrigation rates would lower the temperatures at the top and bottom of the heap. Under these conditions, all parts of the heap could be expected to achieve 65% sulfide oxidation in only 250 days, as indicated by the model.     

Phase structure and mechanical properties of PP/EPR/CaCO3 nanocomposites: Effect of particle's size and treatment

Calcium carbonate (CaCO₃) reinforced polypropylene/ethylene propylene rubber (PP/EPR) copolymer composites for automotive use were developed by means of extrusion and injection molding process. Three kinds of CaCO₃ (stearic acid treated and untreated) nanoparticles and microparticles were used as fillers. The influence of stearic acid, particle size, and filler content on the state distribution and morphology were investigated by SEM and rheological measurements. Two different morphologies were observed: EPR and CaCO₃ dispersed in the PP matrix and a core shell structure, depending on the interactions between EPR and CaCO₃. Toughening mechanisms and mechanical properties of the different systems were investigated. Significant improvement in tensile modulus is observed in all composites, depending on filler content. Elongation and notched impact strength were drastically decreased, especially for composites with nano CaCO₃. Better impact properties were obtained with low content of treated particles, showing the importance of filler treatment. POLYM. ENG. SCI., 55:2859–2868, 2015. © 2015 Society of Plastics Engineers     

Enzymatic Evidence for a Revised Congocidine Biosynthetic Pathway

Naturally produced pyrrolamides, such as congocidine, are nonribosomal peptides that bind to the minor groove of DNA. Efforts to delineate the biosynthetic machinery responsible for their assembly have mainly employed genetic methods, and the enzymes responsible for their biosynthesis remain largely uncharacterized. We report the biochemical characterization of four proteins involved in congocidine formation: the adenylation‐thiolation (A–T) di‐domain Cgc18(1–610), its MbtH‐like partner SAMR0548, the AMP‐binding enzyme Cgc3*, and the T domain Cgc19. We assayed the ATP‐dependent activation of various commercially available and chemically synthesized compounds with Cgc18(1–610) and Cgc3*. We report the revised substrate specificities of Cgc18(1–610) and Cgc3*, and loading of 4‐acetamidopyrrole‐2‐carboxylic acid onto Cgc19. Based on these biochemical studies, we suggest a revised congocidine biosynthetic pathway.     

Thioether Analogues of Disulfide‐Bridged Cyclic Peptides Targeting Death Receptor 5: Conformational Analysis,Dimerisation and Consequences for Receptor Activation

Cyclic peptides containing redox‐stable thioether bridges might provide a useful alternative to disulfide‐bridged bioactive peptides. We report the effect of replacing the disulfide bridge with a lanthionine linkage in a 16‐mer cyclic peptide that binds to death receptor 5 (DR5, TRAIL‐R2). Upon covalent oligomerisation, the disulfide‐bridged peptide has previously shown similar behaviour to that of TNF‐related apoptosis inducing ligand (TRAIL), by selectively triggering the DR5 cell death pathway. The structural and biological properties of the DR5‐binding peptide and its desulfurised analogue were compared. Surface plasmon resonance (SPR) data suggest that these peptides bind DR5 with comparable affinities. The same holds true for dimeric versions of these peptides: the thioether is able to induce DR5‐mediated apoptosis of BJAB lymphoma and tumorigenic BJELR cells, albeit to a slightly lower extent compared to its disulfide homologue. NMR analysis revealed subtle variation in the conformations of the two peptides and suggests that the thioether peptide is slightly less folded than its disulfide homologue. These observations could account for the different capability of the two dimers to cluster DR5 receptors on the cell surface and to trigger apoptosis. Nevertheless, our results suggest that the thioether peptide is a potential candidate for evaluation in animal models.     

Comprehensive study of the influence of total pressure on products yields in fluidized bed gasification of wood sawdust

Wood sawdust gasification experiments were performed in a steam fluidized bed at 800 °C between 2 and 10 bar. An evolution of gas yields with time was measured during the tests, and especially an increase of hydrogen and carbon dioxide yields. This test duration effect was ascribed to char build-up in the bed. As tests proceed, the contribution of char steam gasification to gas yield increases, and the catalytic effect of char on hydrocarbons and tar conversion and on water-gas shift reaction is enhanced.As total pressure increases from 2 to 10 bar, hydrogen, carbon dioxide and methane yields increase by 16%, 53% and 38% respectively, whereas carbon monoxide yield decreases by 33%. The changes in gaseous yields with pressure can be partly explained by the influence of pressure on gas phase reactions (acceleration of water-gas shift kinetics and change in hydrocarbon reactions). The increase of methane yield with pressure is rather suggested to be linked to a change in secondary pyrolysis reactions scheme under high pressure.     

Kinetic study of β‐carotene and lutein degradation in oils during heat treatment

The kinetics of trans‐β‐carotene and trans‐lutein degradation were individually investigated in palm olein and Vegetaline®, at four temperatures ranging from 120 to 180 °C. HPLC‐DAD analysis was carried out to monitor trans and cis carotenoid variations over the heating time at each temperature. In both oils, initial trans‐β‐carotene and trans‐lutein degradation rates increased with temperature. Trans‐lutein was found to degrade at a slower rate than trans‐β‐carotene, suggesting a higher thermal resistance. The isomers identified were 13‐cis‐ and 9‐cis‐β‐carotene, and 13‐cis‐, 9‐cis‐, 13'‐cis‐, and 9'‐cis‐lutein. In spite of the higher number of lutein cis isomers, their total amount was lower than that of β‐carotene cis isomers. Trans and cis carotenoids were involved in degradation reactions at rates that increased with temperature. All degradation rates were generally found to be lower in Vegetaline® than in palm olein. These results were explained by the initial composition of the two oils and especially their peroxide and vitamin E contents.     

Improvement of the in vitro digestible iron and zinc content of okra (Hibiscus esculentus L.) sauce widely consumed in Sahelian Africa

ABSTRACT:  The effects of the formulation (okra, fish, soumbala, extract of wood ash) and cooking time of okra sauce on total iron and zinc content and on their in vitro digestibility were evaluated following a Doehlert uniform shell design with 5 factors and 33 trials. Cooking time had no significant effect on in vitro digestible iron and zinc content, whereas formulation did. Each ingredient had a specific effect. Extract of wood ash, which is a source of soluble and digestible iron and zinc, is a good way of increasing the digestible mineral content of the dish. Okra, the main ingredient in this sauce, has a negative effect and should be added in moderate quantities (< 37.7% of the DM of the sauce). An optimization using the desirability function allows us to identify the optimal recipe that enabled the quantity of digestible iron to be doubled and the quantity of digestible zinc to be increased by one third. This recipe calls for a mixture of 37.7% okra, 26.3% dried fish, 18.5% soumbala, and 3.7% extract of wood ash cooked for 25 min.     

Structure and Technofunctional Properties of Protein-Polysaccharide Complexes: A Review

Food proteins and polysaccharides are the two key structural entities in food materials. Generally, interactions between proteins and polysaccharides in aqueous media can lead to one- or two-phase systems, the latter being generally observed. In some cases of protein-polysaccharide net attraction, mainly mediated through electrostatic interactions, complex coac-ervation or associative phase separation occurs, giving rise to the formation of protein-polysac-charide complexes. Physicochemical factors such as pH, ionic strength, ratio of protein to polysaccharide, polysaccharide and protein charge, and molecular weight affect the formation and stability of such complexes. Additionally, the temperature and mechanical factors (pressure, shearing rate, and time) have an influence on phase separation and time stability of the system. The protein-polysacchaide complexes exhibit better functional properties than that of the proteins and polysaccharides alone. This improvement could be attributed to the simultaneous presence of the two biopolymers, as well as the structure of the complexes. Consequently, the interesting hydration (solubility, viscosity), structuration (aggregation, gelation) and surface (foaming, emulsifying) properties of these complexes can be used in a number of domains. Among others, these could be macromolecular purification, microencapsulation, food formulation (fat replacers, texturing agents), and synthesis of biomaterials (edible films, artificial grafts).     

Constructal design of distributed cooling on the landscape

Here we constructal design to determine the area size (or number of users N) to be allocated to a central refrigeration plant, and to configure the distribution network for the distributed cooling system. The main objective is to maximize the net cooling capacity delivered to every user, and to minimize the pumping power required for transporting the chilled water. Two types of distribution networks are investigated: radial and tree‐shaped networks. First, when ducts with a single diameter are used, the net cooling capacity delivered to every user is almost the same, while the pumping power requirement for the tree network is greater than that for the radial network. Multi‐diameter tree networks are investigated next. The pumping power requirement for multi‐diameter tree‐shaped network is less than for radial network when N is greater than 19 if the flow is laminar, and when N is greater than 80 if the flow is turbulent. The global performance of the area‐based cooling system can be improved by increasing the freedom to morph the configuration. Copyright © 2010 John Wiley & Sons, Ltd.