液压集成块校核软件的编制和应用

本文叙述了液压集成块校核软件的编制思想和方法，并重点介绍了编制过程中所使用的相关技术，同时给出部分源程序。     

氨气提工艺尿素生产中操作的改进

中原大化集团公司尿素装置在操作上使用的是Ｓｎａｍ公司提供的尿素操作手册 ,在运行过程中 ,发现有许多地方与实际状况出入很大 ,经过不断的总结经验 ,并在工艺操作中进行改进、优化 ,使装置达到安全、稳定、经济运行的目的。1　二氧化碳压缩机操作方式的改进二氧化碳压缩机自开车以来 ,防喘振系统一直未投用。由于Ｓｎａｍ公司提供的防喘振曲线富裕度较大 ,操作人员对实际喘振点不清楚 ,正常生产中转速控制较高 ,操作盲目性很大 ,在 1 0 0 %负荷下 ,防喘振阀仍有 1 0 %左右的开度 ,造成蒸气消耗偏高。1 999- 0 3- 31 ,对二氧化碳压缩机各…     

单晶凝固组织的样品尺寸效应

通过对不同直径的单晶样品的凝固实验，研究了样品尺寸对单晶凝固组织的影响规律，研究发现，随样品尺寸减小，单晶凝固组织被细化，尤其一次枝晶间距λ1和枝晶间γ′相尺寸对样品尺寸的依赖性更为明显；样品尺寸影响的要质在于此表面积的变化，进而对凝固过程温度梯度产生影响，最终作用于凝固组织和力学性能，一次枝晶间距λ1和枝晶间γ′尺寸与样品的比表面积近拟呈线性关系，样品尺寸变化，明显改变了单晶生长过程的温度梯度和合金的高温持久寿命。     

Effects of alloy additions on the microstructures and tensile properties of cast Co-Cr-Mo alloy used for surgical implants

The composition of the Co-Cr-Mo alloy has been modified by additions of nickel and some trace elements aluminium, titanium and boron. In this paper, the first part of the present study, the effects of alloy additions on the microstructures and tensile properties of the as-cast Co-Cr-Mo alloy are discussed. The effects of alloy additions on the fatigue behaviour of the alloy will be discussed in the second part of the present study. It is found that alloy additions do not seem to result in changes in the nature of the casting structure. A directional, coarse dendritic cast structure is produced in the modified alloys as in the base alloY. However, the alloy additions affect the carbide precipitations and the formation of some fine details of the microstructure such as dislocations, stacking faults and twins produced during the solidification. A considerable improvement in the transient mechanical properties, especially in the tensile ductility, is achieved by modifying the base alloy with alloy additions.     

Preparation of BaMgAl10O17∶Eu2+ and Its Phase Behavior in Microemulsion System

BaMgAl10O17∶Eu2 (BAM) was prepared in the microemulsion system and its phase behavior was studied. There exists a small region in the reverse microemulsion system where the dispersed particles are of spherical form. In this way, BAM blue phosphor with good dispersion can be synthesized. The microemulsion phase diagrams of the pseudo-ternary system (Triton X-100/cosurfactant-oil-BAM brine) were first established intuitively by the dilution method. The microstructure of microemulsions was determined through eyeballing, conductance technique, and polar optical microscopy. Its phase behavior is affected by various factors, such as temperature (room temperature, 30, 40 ℃), oil, surfactants, and cosurfactants in microemulsions. According to the phase diagrams, the microemulsion system of Triton X-100/1-hexanol-hexane-BAM brine was chosen to prepare the precursor. The BAM phosphor can be obtained via sintering the precursor at a comparatively low temperature. The phosphors were characterized by XRD and vacuum ultraviolet (VUV) spectra.     

基体温度对磁控溅射沉积ZAO薄膜性能的影响

利用中频交流磁控溅射方法 ,采用氧化锌铝陶瓷靶材 [w(ZnO) =98%、w(Al2 O3 ) =2 % ]制备了ZAO(ZnO∶Al)薄膜 ,观察了基体温度对ZAO薄膜的晶体结构、电学和光学性能的影响 ,采用X射线衍射仪对薄膜的结构进行了分析 ,采用光学分度计和电阻测试仪测量了薄膜的光学、电学特性 ,采用霍尔测试仪测量了薄膜的载流子浓度和霍尔迁移率。结果表明 :沉积薄膜时的基体温度对薄膜的结构、结晶状况、可见光透射率以及导电性有较大的影响。当基体温度为 2 5 0℃ ,Ar分压为 0 8Pa时 ,薄膜的最低电阻率为 4 6× 10 -4Ω·cm ,方块电阻为 35Ω时 ,可见光 (λ =5 5 0nm)透射率高达 92 0 %。     

S广义ω－凸语言

本文通过在Σω上定义半序关系“≤ωｓ，引进了Ｓ广义ω－左凸语言、Ｓ广义ω－右凸语言和Ｓ厂义ω－凸语言的概念，并给出了各类Ｓ广义ω－凸语言与其前缀语言之间的关系；还给出了各类Ｓ厂义ω－凸语言族对布尔运算的封闭性以及各类Ｓ广义ω－凸语言的充分必要条件。     

掺钛蓝宝石激光晶体中夹杂物的分析

本文用大视场光学显微镜、电子探针观察和分析了掺钛蓝宝石激光晶体中夹杂物的形状、尺寸大小及元素组成，并提出消除和减少这些夹杂物的方法．     

以YAG为添加剂的气压烧结氮化硅

本文以添加ＹＡＧ的反应烧结氮化硅（ＲＢＳＮ）为前驱体，采用气氛加压烧结的工艺，在０．５～９．０ＭＰａ氮气压力范围，研究了不同氮压对烧结体的密度、相组成、强度和显微结构的影响及其相互间的关系。研究表明，通过改变氮气压力能有效地调控材料的显微结构，材料的性能又受控于显微结构的变化。