广州清洁燃料汽车发展方向

选择好合适的汽车替代燃料，科学确定一个地区清洁燃料汽车的发展方向，是减少机动车有害尾气排放、控制城市大气环境污染重大而紧迫的课题。国内外汽车清洁燃料的发展规律表明，天然气特别是液化天然气，是汽车替代燃料的最佳选择与发展方向。为此，探讨了随着天然气工业的加快发展，作为广州这样一座已经发展液化石油气汽车并已形成有一定规模的城市，如何适应新形势的需求，科学决策，选择符合国家能源发展政策并适应当地具体实际的汽车清洁燃料路线，寻求顺利实施液化石油气与天然气两种清洁燃料平稳过渡的具体措施。最后提出以下建议：加速LNG加气站和液化天然气汽车（LNGV）相关技术规范的制定；加快实现LNG关键设备，如LNG泵、LNG售气机、车用LNG储罐的国产化步伐，以降低LNGV和加气站的成本；鉴于LNGV改装技术的现状，不提倡对在用车进行改装，而应加大力度，逐步推广单燃料LNG汽车。     

催化精馏合成N-异丙基苯胺

在Joback基团贡献法估算反应的G ibbs函数的基础上,得到了异丙醇与苯胺合成N-异丙基苯胺的平衡常数与反应温度的关系式。研究了回流比、异丙醇与苯胺的摩尔比、塔釜操作温度、苯胺进料口位置距塔顶的距离对异丙醇与苯胺催化精馏合成N-异丙基苯胺的影响,确定了适宜的工艺条件:回流比2.5~3.5、异丙醇与苯胺的摩尔比1.5、塔釜操作温度223℃、苯胺进料口位置距塔顶300~400mm。在优化条件下,苯胺的转化率可达到99%,N-异丙基苯胺的选择性可达到99.5%,N-异丙基苯胺的质量分数可稳定在98.8%以上。     

H型丝光沸石催化剂催化甲苯与叔丁醇的烷基化反应

针对合成对叔丁基甲苯传统工艺中存在的缺点,采用环境友好、可重复利用的H型丝光沸石催化剂(以下简称催化剂)进行了甲苯与叔丁醇的烷基化反应,并用X射线衍射和氨程序升温脱附等方法对不同焙烧温度下得到的催化剂的物相结构和酸性质进行了表征,研究了各种反应条件对催化剂的催化性能的影响。实验结果发现,在适宜的操作条件下,即催化剂的焙烧温度823K、反应温度180℃、反应时间3h、初始压力1.0MPa、原料与催化剂的质量比为8、叔丁醇与甲苯的摩尔比为4、溶剂环己烷与甲苯的摩尔比为5时,甲苯转化率达42.73%,叔丁基甲苯的选择性为96.30%,对叔丁基甲苯的选择性为80.37%。     

智能动态网络资源分配系统

通过对解决GSM移动通信网络热点区域话务拥塞问题的研究，提出了利用可控功分器实现智能动态网络资源的分配，解决不同种类的话务拥塞问题，并着重讨论了该系统目前的成功运用及前景。     

Automatic image hanging protocol for chest radiographs in PACS.

Chest radiography is one of the most widely used techniques in diagnostic imaging. It comprises at least one-third of all diagnostic radiographic procedures in hospitals. However, in the picture archive and communication system, images are often stored with the projection and orientation unknown or mislabeled, which causes inefficiency for radiologists' interpretation. To address this problem, an automatic hanging protocol for chest radiographs is presented. The method targets the most effective region in a chest radiograph, and extracts a set of size-, rotation-, and translation-invariant features from it. Then, a well-trained classifier is used to recognize the projection. The orientation of the radiograph is later identified by locating the neck, heart, and abdomen positions in the radiographs. Initial experiments are performed on the radiographs collected from daily routine chest exams in hospitals and show promising results. Using the presented protocol, 98.2% of all cases could be hung correctly on projection view (without protocol, 62%), and 96.1% had correct orientation (without protocol, 75%). A workflow study on the protocol also demonstrates a significant improvement in efficiency for image display.     

On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

Exposed Die-Top Encapsulation Molding for an Improved High- Performance Flip Chip BGA Package

The recent advancement in high- performance semiconductor packages has been driven by the need for higher pin count and superior heat dissipation. A one-piece cavity lid flip chip ball grid array (BGA) package with high pin count and targeted reliability has emerged as a popular choice. The flip chip technology can accommodate an I/O count of more than five hundreds500, and the die junction temperature can be reduced to a minimum level by a metal heat spreader attachment. None the less, greater expectations on these high-performance packages arose such as better substrate real estate utilization for multiple chips, ease in handling for thinner core substrates, and improved board- level solder joint reliability. A new design of the flip chip BGA package has been looked into for meeting such requirements. By encapsulating the flip chip with molding compound leaving the die top exposed, a planar top surface can be formed. A, and a flat lid can then be mounted on the planar mold/die top surface. In this manner the direct interaction of the metal lid with the substrate can be removed. The new package is thus less rigid under thermal loading and solder joint reliability enhancement is expected. This paper discusses the process development of the new package and its advantages for improved solder joint fatigue life, and being a multichip package and thin core substrate options. Finite-element simulations have been employed for the study of its structural integrity, thermal, and electrical performances. Detailed package and board-level reliability test results will also be reported     

Routing Correlated Data with Fusion Cost in Wireless Sensor Networks

In this paper, we propose a routing algorithm called minimum fusion Steiner tree (MFST) for energy efficient data gathering with aggregation (fusion) in wireless sensor networks. Different from existing schemes, MFST not only optimizes over the data transmission cost, but also incorporates the cost for data fusion, which can be significant for emerging sensor networks with vectorial data and/or security requirements. By employing a randomized algorithm that allows fusion points to be chosen according to the nodes' data amounts, MFST achieves an approximation ratio of 5/4log(k + 1), where k denotes the number of source nodes, to the optimal solution for extremely general system setups, provided that fusion cost and data aggregation are nondecreasing against the total input data. Consequently, in contrast to algorithms that only excel in full or nonaggregation scenarios without considering fusion cost, MFST can thrive in a wide range of applications     

膜电极结构对质子交换膜燃料电池性能的影响

膜电极(MEA)作为质子交换膜燃料电池(PEMFC)的核心组件之一，其结构和组成对电池的性能有着重要的影响。提高膜电极性能的一个重要的指导思想是在催化粒子的周围形成良好的质子、电子和气体通道。以此为主线，从电极制备工艺的发展历程，Nafion的使用与质子通道的改进、电子通道的改进、阴极催化等几个方面详细地总结和讨论了近年来MEA的研究状况，并在此基础上对MEA的进一步研究提出了若干建议。     

基于C6711处理器cdma2000 1X系统前向信道信号的处理

在cdma20001x前向信道中,要对一段信号进行传送,一般选用QPSK调制,因为QPSK调制比QAM更适合噪音环境。采用TI6000系列的TMS320C6711芯片处理前向信道信号,可以对复杂性和实时性较高的信号做采集、量化、编码、调制等实时处理,主要功能通过软件编程实现,从而使系统具有结构灵活、可靠性高、可扩展等优点。