电压对电刷镀三价铬镀层性能的影响

在45钢表面电刷镀得到三价铬镀层,镀液组成和工艺条件为:Cr2(SO4)36H2O 0.4 mol/L,甲酸铵0.5 mol/L,氨基乙酸0.5 mol/L,H3BO30.6 mol/L,NaH2PO2 H2O 0.3 mol/L,pH=1.5,温度50°C,镀笔移动速率15 cm/s。研究了电压对镀铬层显微结构、表面粗糙度、厚度、显微硬度和耐磨性的影响。随电压增大,镀层厚度增大,显微硬度和耐磨性均先提高后降低。电压为14 V时,镀层的表面平整,粗糙度为2.387μm,显微硬度为602 HV,耐磨性最好。     

再生骨料自密实清水混凝土配合比优化及表观性能试验研究

利用再生粗骨料制备再生骨料自密实清水混凝土,采用正交试验的方法对再生骨料自密实清水混凝土的配合比进行优化,探究了水胶比、砂率及胶凝材料含量对混凝土工作性能、力学性能以及表观性能的影响规律及显著性.通过对试验结果的极差分析,发现胶凝材料含量对混凝土坍落扩展度影响最大,其次是砂率,水胶比的影响最小;对于7d抗压强度的影响程度从大到小依次为水胶比、砂率、胶凝材料含量;混凝土表面灰度标准差受胶凝材料含量影响最大,其次是水胶比和砂率;对混凝土表面气孔率的影响程度从大到小依次为胶凝材料含量、砂率、水胶比.通过方差分析得到水胶比与砂率对再生骨料自密实清水混凝土的7d抗压强度具有显著性影响;胶凝材料含量对坍落扩展度、灰度标准差和气孔率有显著性影响.     

The formation of fibrous structure of polyamide 6 induced by the three-step forming process and its prominent reinforcement in nitrile rubber

Nitrile rubber (NBR) blends with excellent performance have always been a hot research topic in petroleum field. Due to the excellent performance and compatibility of polyamide 6 (PA6), it provides an opportunity for the preparation of high-performance NBR/PA6 blends. In this article, NBR/PA6 blends were prepared by the three-step molding process. Experimentally, it was found that PA6 has a prominent reinforcement effect in NBR matrix. The variation of this mechanical property was investigated from different aspects of the crystal structure, crystallinities, phase morphology, and so on. It can be cleared that the formation of fibrous structure of PA6 phase is the main factor for reinforcement of the polymer blends. Meanwhile, the formation mechanism of the special phase structure induced by the three-step process is deeply expounded and its structural evolution schematic is established. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47472.     

测量二次电子空间分布特征矩阵法的有效性分析

为了准确测量不同材料在实际环境中的二次电子空间分布，设计了一种新型的二次电子发射空间分布测量结构，给出了实验测量原理，用求解特征矩阵的方法对实验结果进行处理，得到了所需的二次电子空间分布。通过模拟计算对该测量方法进行了校验，模拟结果与假设二次电子空间分布函数相吻合，表明该测量方法可靠、测量精度高，为后续样机研制奠定了理论基础。     

EPMDA: an efficient privacy-preserving multi-dimensional data aggregation scheme for edge computing-based IoT system

In order to perform multi-dimensional data aggregation operations efficiently in edge computing-based Internet of things (IoT) systems, a new efficient privacy-preserving multi-dimensional data aggregation (EPMDA) scheme is proposed in this paper. EPMDA scheme is characterized by employing the homomorphic Paillier encryption and SM9 signature algorithm. To improve the computation efficiency of the Paillier encryption operation, EPMDA scheme generates a pre-computed modular exponentiation table of each dimensional data,and the Paillier encryption operation can be implemented by using only several modular multiplications. For the multi-dimensional data, the scheme concatenates zeros between two adjacent dimensional data to avoid data overflow in the sum operation of ciphertexts. To enhance security, EPMDA scheme sets random number at the high address of the exponent. Moreover, the scheme utilizes SM9 signature scheme to guarantee device authentication and data integrity. The performance evaluation and comparison show that EPMDA scheme is more efficient than the existing multi-dimensional data aggregation schemes.     

锂辉石-氧化钙烧结法提锂的物相重构与动力学

对锂辉石-氧化钙烧结过程进行热力学分析，绘制了各反应Gibbs自由能与温度的关系图。结果表明，Al₂O₃会优先和Na₂O、Li₂O、K₂O反应，然后与CaO反应生成CaO·Al₂O₃，而且烧结温度需高于1060℃以保证LiAlSi₂O₆能够完成晶形转变。并探讨了锂辉石-氧化钙烧结法提锂的反应机理。考察了不同烧结条件对锂浸出率的影响并对熟料进行X射线衍射（XRD）分析表征。实验结果表明，在配料比为1∶1.25、烧结温度1150℃、烧结时间60min时，锂的浸出率达到92.14%，熟料中的主要物相为Ca₂SiO₄与LiAlO₂。利用XRD和扫描电镜-能谱联用仪（SEM-EDS）对熟料与浸出渣的物相、显微形貌及元素分布情况进行了分析表征。为了确定烧结反应的控制性步骤，在最优烧结条件的基础上对烧结过程进行动力学分析，结果表明，锂辉石-氧化钙烧结体系属于球形颗粒三维界面化学反应控制，烧结过程的动力学拟合方程为\mathrm{1}-{(\mathrm{1}-x)}^{\mathrm{1}/\mathrm{3}}=\mathrm{0.00677}t。     

气液螺旋环状流压降特性研究

考虑旋流衰减的影响，对气液螺旋环状流的压降特性进行研究并推导出了螺旋环状流压降预测模型。定义压降旋-直比系数为气液两相螺旋环状流和气液两相直流的压降之比，以此来表征旋流衰减对压降的影响。基于量纲分析的方法对压降旋-直比系数进行分析，推导出其表达式，压降旋-直比系数依赖于Lockhart-Martinelli 参数和气相Froude数变化。最终，得出了气液两相螺旋环状流的压降预测模型。在50 mm内径的水平管内对螺旋环状流的压降特性进行了实验研究，其中气相表观流速变化范围为10~16 m/s，体积含液率（LVF）变化范围为0.6%~4.8%。通过与实验数据进行对比，压降预测模型的相对误差在±15%以内，为工程应用提供了参考。     

Preparation and characterization of calcium phosphate cement with enhanced tissue adhesion for bone defect repair

Anti-washout and tissue adhesion properties are essential for the clinical application of injectable bone materials. In this study, we prepared calcium phosphate cement (CPC) with anti-washout and tissue adhesion properties and attempted to build covalent bonds between CPC and the amino groups in bone tissue under a self-regulating pH system in the CPC (acidic to basic). The results of push-out tests demonstrated that a significant enhancement (from 6.42 ± 0.76 N to 61.5 ± 4.09 N) in tissue adhesion was obtained with the addition of 6% (w/w) oxidized sodium alginate (OSA) in CPC. The FTIR, XRD, anti-washout test, XPS, pH test, and SEM results suggested that the synergistic effect of OSA-citric acid (CA) led to the formation of a three-dimensional gel network structure in the CPC, and the Schiff base reaction between aldehyde and amino groups induced adhesion between CPC and the bone tissue. Further, the addition of less OSA had no significant negative effect on the hydration properties of CPC. Our work aims to promote the development of injectable bone material in clinical applications.