Transport of lithium through a supported liquid membrane of LIX54 and TOPO in kerosene

A mathematical transport model is developed for the extraction of lithium from dilute synthetic solution, simulating geothermal water, using a supported liquid membrane (SLM) of LIX54 (major component is -acetyl-m-dodecylacetophenone) and TOPO (tri-n-octylphosphine oxide) in kerosene. The model is based on fundamental mass transfer and kinetics mechanisms that account for all possible transport resistances. The model is solved numerically and is used to investigate the effect of various extraction conditions and membrane support characteristics. Reasonable agreement is found between the predicted and the experimental results reported in literature.     

Utility scale wind turbines on a grid-connected island: A feasibility study

This paper analyzes the technical and economic feasibility of installing utility-scale wind turbines on the Fox Islands, located 12 miles from the coast of Maine in the United States. Three locations on the islands, as well as a near offshore site, are analyzed in detail as potential sites for wind turbine installations. As discussed in this work, the logistic problems of transporting and installing wind turbines on the island require innovative solutions. These include locally available amphibious vessels, which can land turbine components at suitable shallow spots on the island, self-erecting towers, which allow use of a smaller crane for installation, and a special turbine foundation suitable for the local ground conditions. In the economic analysis, in addition to standard life-cycle parameters, renewable energy credits (REC) were also included. This work concludes that the installation of sub-megawatt wind turbines on the island is logistically possible and will lead to a reduction in the cost of electricity to the customers.     

Enhanced β-galactosidase production by supplementing whey with cauliflower waste

Among the five Kluyveromyces marxianus strains tested for β-galactosidase production, K. marxianus NCIM 3465 showed maximum enzyme activity of 1.62 IU mg⁻¹ dry weight. Different levels (5–25%, w/v) of dried cauliflower waste were incorporated into whey to evaluate the effect of its supplementation on enzyme production. Although a marginal increase in enzyme production was seen by incorporating 5% and 10% cauliflower waste in whey, nearly 15% increase in β-galactosidase production was observed when cauliflower waste level was increased to 20% compared with whey alone. Supplementing whey with 20% cauliflower waste also decreased the production time. Lactose concentration in whey, mainly responsible for increasing the biological oxygen demand load of the effluent water, decreased from 4.2% to nearly 0% at 24 h. Thus, this study demonstrated that both these by-products/residues could be effectively used for β-galactosidase production at commercial scale.     

Thermopower measurements on BiSrCaCuO system

We report thermoelectric power measurements on BiSrCaCuO (2212) superconducting oxide and compare the observed behaviour with that of the YBaCuO (123) system. The relative importance of phonon drag and diffusion thermopower contributions is evaluated for the two systems by analysing the data using a generalized expression of the typeS=αT+β/T. The thermopower enhancement effect just aboveT _c gives parameter values comparable to those of YBa₂Cu₃O_7−x system.     

Hill slope instability of Nainital City,Kumaun Lesser Himalaya,Uttarakhand, India

Nainital City of Kumaun Lesser Himalaya is prone to mass wasting processes during monsoon season, which mischievously triggers the hill slope instability in this region. Slate, dolomitic limestone, silty sandstone and rhythmite of the Krol Formation are the main rock types. The present study focuses on the investigation of slope stability in the region in terms of potential seismicity and landslide. Geological and geotechnical mapping indicates that the major portion of the area is characterized by slope wash materials and buildings. The combination of 3–4 joint sets with one random joint is the main structure at outcrops. The major geological structures of this area are Nainital lake fault passing from the center of the lake, Main Boundary Thrust at SW, and Khuriya Fault passing from the SE direction of Nainital City. This work finds that different types of discontinuities (e.g. joints and faults), overburden due to unplanned civil structures, and neotectonic activity in the vicinity of this area affect the stability of the city. The slate forms the base of the city, dipping slightly towards the lake side along the NW direction, thus accelerating the instability of this area. Rock mass rating (RMR), slope mass rating, factor of safety (FOS) and graphical analysis of the discontinuity for slope kinematics indicate that the study area is a landslide-prone zone. This study can facilitate reducing the risk of human life, and contribute to the ongoing construction works in the area.     

Interaction of lanthanide and actinide with BaHfO3 perovskite: A case study with cerium and uranium

Speciation of actinide (An) and lanthanide (Ln) in technologically important ceramics is very important from both fundamental as well as technological aspects. The intrinsic structural flexibility of perovskite containing AO₆ and BO₁₂ polyhedra makes them suitable and rich hosts for An and Ln. In this work, emphasis was given to deciphering information such as oxidation state, local dopant site, charge compensating defects, excited state kinetics, and so forth in BaHfO₃ (BHO) related to dopant uranium (BHO-U) and cerium (BHO-Ce). Several spectroscopic techniques namely, time-resolved photoluminescence (TRPL), positron annihilation lifetime spectra (PALS), and thermoluminescence (TL) spectroscopy coupled with density functional theory (DFT) were employed to probe the same. Ce and U though are distributed at both Ba and Hf sites, Ce prefers the former, while U prefers the latter site. Uranium on the other hand stabilizes as U⁶⁺ in the form of octahedral uranate ion giving green emission. PALS suggested the formation of defects in BHO-Ce and BHO-U with oxygen vacancies predominating in the former whereas BHO-U perovskites are loaded with cation vacancies and vacancy clusters. These cation vacancies are responsible for lower TL output in BHO-U. TL measurements also suggested cerium doping leads to a higher density of deeper traps in BHO-Ce compared to uranium doping in BHO-U which is in concurrence with DFT results and may have implications in designing afterglow phosphors based on perovskite. We believe this work would have a long-term impact on exploring the potential of perovskite for nuclear waste host and afterglow phosphors applications.     

CLAMP: Efficient class-based sampling for flexible flow monitoring

With an increasing requirement to classify traffic and track security threats, newer flexible and efficient ways are needed for collecting traffic statistics and monitoring network flows. However, traditional solutions based on packet sampling do not provide the flexibility required for these applications. For example, operators are often interested in observing as many unique flows as possible; however, random packet sampling is inherently biased towards large flows. Operators may also be interested in increasing the fidelity of flow measurements for a certain class of flows; such flexibility is lacking in today’s packet sampling frameworks. In this paper, we propose a novel architecture called CLAMP that provides an efficient framework to implement class-based sampling. At the heart of CLAMP is a novel data structure we propose called composite Bloom filter (CBF) that consists of a set of Bloom filters working together to encapsulate various class definitions. In particular, we show the flexibility and efficacy of CLAMP by implementing a simple two-class size-based sampling. We also consider different objectives such as maximizing flow coverage and improving the accuracy of certain class of flows. In comparison to previous approaches that implement simple size-based sampling, our architecture requires substantially lower amounts of memory (up to 80×) and achieves higher flow coverage (up to 8× more flows) under specific configurations.     

Influence of reaction conditions on the formation of nanotubes/nanoparticles of polyaniline in the presence of 1‐amino‐2‐naphthol‐4‐sulfonic acid and applications as electrostatic charge dissipation material

BACKGROUND: Poly(1‐amino‐2‐naphthol‐4‐sulfonic acid) and its copolymers with aniline are a new class of conducting polymers which can acquire intrinsic protonic doping ability, leading to the formation of highly soluble self‐doped homopolymers and copolymers. Free ? OH and ? NH₂ groups in the polymer chain can combine with other functional groups that could be present in protective paints which can thus be successfully used as antistatic materials. RESULTS: This paper reports the formation of nanotubes of polyaniline on carrying out oxidative polymerization of aniline in the presence of 1‐amino‐2‐naphthol‐4‐sulfonic acid (ANSA) in p‐toluenesulfonic acid (PTSA) as an external dopant. The presence of ? SO₃H groups in the ANSA comonomer allows the copolymer to acquire intrinsic protonic doping ability. The polymerization mechanism was investigated by analysing the ¹H NMR, ¹³C NMR, Fourier transform infrared and X‐ray photoelectron spectra of the copolymers and homopolymers, which revealed the involvement of ? OH/? NH₂ in the reaction mechanism. Scanning and transmission electron microscopy showed how the reaction route and the presence of a dopant can affect the morphology and size of the polymers. Static decay time measurements were also carried out on conducting copolymer films prepared by blending of 1 wt% of copolymers of ANSA and aniline with low‐density polyethylene (LDPE) which showed a static decay time of 0.1 to 0.31 s on dissipating a charge from 5000 to 500 V. CONCLUSION: Copolymers of ANSA with aniline were synthesized in different reaction media, leading to the formation of nanotubes and nanoparticles of copolymer. Blends of 1 wt% of PTSA‐ and self‐doped copolymers of ANSA and aniline with LDPE can be formulated into films with effective antistatic properties. Copyright © 2009 Society of Chemical Industry     

Autoignition and front propagation in low temperature combustion engine environments

In this paper, we computationally investigate the fundamental aspects of autoignition and subsequent combustion phenomena in low temperature combustion (LTC) engine environments using direct numerical simulations (DNS). In particular, the effects of thermal and equivalence ratio stratification on the autoignition and subsequent front propagation in high pressure and stratified hydrogen-air turbulent mixtures are studied using detailed chemistry. Depending on fuel injection timing, exhaust gas recirculation, and wall heat loss, different correlations between temperature (T) – equivalence ratio (?) fields can exist prior to the major heat release event. Here, we investigate three cases with different initial T–? correlations: (A) a baseline case of a uniform composition with temperature inhomogeneities only, (B) uncorrelated T–? fields, and (C) negatively-correlated T–? fields. Numerical diagnostics are developed based on an appropriately defined Damköhler number to distinguish different modes of heat release. It is found that the majority of heat release in the baseline case and the uncorrelated case occurs during the front propagation in the form of both spontaneous ignition fronts as well as deflagration waves, whereas the negatively correlated case ignites predominantly homogeneously.