Measurement of solubility and diffusion coefficients of ethylene in solid and molten low-density polyethylene with different melt indices

The diffusion behavior of ethylene in polyethylene is of great importance for the polymerization and degassing of polyethylene (PE) industry. Based on the gravimetric sorption and desorption measurement approach, an intelligent gravimetric analyzer is applied to obtain the solubility and diffusion coefficients of ethylene in solid low-density PE (LDPE) with different melt indices at 30°C to 70°C, 0 to 4 atm and in molten LDPE at 160°C to 230°C, 0 to 4 atm, respectively. Results indicate that both the solubility and diffusion coefficients of ethylene in solid LDPE are smaller than those in molten LDPE, while the dissolution enthalpy and diffusion activation energy of ethylene in solid LDPE are higher. In addition, one- and two-dimensional diffusion models are built and the effects of particle size, polymer properties, and operation conditions are systematically investigated on the diffusion behaviors of ethylene in solid and molten LDPE.     

Chromium evaporation and oxidation characteristics of alumina-forming austenitic stainless steels for balance of plant applications in solid oxide fuel cells

The chromium (Cr) evaporation behavior of several different types of iron (Fe)-based AFA alloys and benchmark Cr₂O₃-forming Fe-based 310 and Ni-based 625 alloys was investigated for 500 h exposures at 800 °C to 900 °C in air with 10% H₂O. The Cr evaporation rates from alumina-forming austenitic (AFA) alloys were ~5 to 35 times lower than that of the Cr₂O₃-forming alloys depending on alloy and temperature. The Cr evaporation behavior was correlated with extensive characterization of the chemistry and microstructure of the oxide scales, which also revealed a degree of quartz tube Si contamination during the test. Long-term oxidation kinetics were also assessed at 800 to 1000 °C for up to 10,000 h in air with 10% H₂O to provide further guidance for SOFC BOP component alloy selection.     

Improvement of polyamide/thermoplastic polyurethane blends with polyamide 6-polyurethane copolymer prepared via suspension polymerization as compatibilizer

The polyamide 6-polyurethane copolymer (PA6-b-PU-b-PA6) was synthesized through anionic suspension polymerization and then mixed with polyamide 6/thermoplastic polyurethane (PA6/TPU) and polyamide 6, 6/thermoplastic polyurethane (PA66/TPU) blends using as the compatibilizer. The results show that the PA6-b-PU-b-PA6 copolymers powders several can be obtained through suspension polymerization using dimethicone as disperse medium. The average diameter of PA6-b-PU-b-PA6 copolymer powders decreased with the increasing of PU content. With the addition of PA6-b-PU-b-PA6, the TPU phase dispersed more uniformly in PA6 or PA66 matrix, and the size of TPU dispersed phase decreased obviously. The PA6-b-PU-b-PA6 copolymer with higher PU content shows better compatibilizing effect. Addition of PA6-b-PU-b-PA6 can improve both strength and toughness of the PA/TPU blends. When the amount of PA6-PU25% copolymer was 5 phr, the tensile strength and notched impact strength of PA6/TPU/PA6-PU25% blends increased 29 and 159.4%, respectively, compared to the PA6/TPU blend without compatibilizer.     

Photocatalytic degradation and heat reflectance recovery of waterborne acrylic polymer/ZnO nanocomposite coating

This work aims to clarify the photocatalytic degradation mechanism and heat reflectance recovery performance of waterborne acrylic polymer/ZnO nanocomposite coating. To fabricate the nanocomposite coating, ZnO nanoparticles (nano-ZnO) were dispersed into acrylic polymer matrix at the various concentrations from 1 to 6% (by total weight of resin solids). The photocatalytic degradation of nanocomposite coating under ultraviolet (UV) light irradiation has been investigated by monitoring its weight loss and chemical/microstructural/morphological changes. As the topcoat layer, its heat reflectance recovery has been evaluated under UV/condensation exposure by using an artificial dirty mixture of 85 wt% nanoclay, 10 wt% silica particles (1–5 μm), 1 wt% carbon black, and 2 wt% engine oil. After 108-cycle UV/condensation exposure, infrared spectra and weight loss analysis indicated that the maximal degradation for nanocomposite coating is observed at 1 wt% nano-ZnO. On the other hand, after 96 hr of UV light exposure, the nanocomposite coating with1 wt% nano-ZnO could restore effectively the reflective index of solar-heat reflectance coating (from 58.45 to 80.78%). Finally, the photodegradation mechanism of this waterborne acrylic polymer coating has been proposed as the UV-induced formation of CC CO conjugated double bonds. As a result, its self-cleaning phenomenon can be achieved as the recovery of heat reflectance.     

基于步冷试验的2.25Cr-1Mo-0.25V钢母材及焊缝回火脆化研究

对原始态、步冷态、脱脆态和脱脆步冷态2.25Cr-1Mo-0.25V钢母材及焊缝冲击试验结果进行分析,得到了母材和焊缝在不同状态下的韧脆转变温度vTr54.2和FATT以及脆化度ΔvTr54.2和ΔFATT。试验结果表明,步冷试验之后,母材发生较低程度脆化或脱脆现象,但是脆化度或脱脆度较低,表明母材具有良好的抗回火脆化性能;经脱脆试验后,母材和焊缝都发生较高程度的脱脆,表明材料的脆化主要是由于回火脆化引起的,脱脆试验使得材料的韧脆转变温度降低;脱脆步冷试验后,焊缝发生较高程度的脆化,焊缝对脱脆步冷试验的敏感性较高,脱脆步冷试验有效促进了焊缝的脆化。在相同脆化条件下,母材的脆化敏感性低于焊缝,焊缝更易发生脆化。     

浙江废弃矿井现状调查及影响分析

浙江省废弃矿井占据了大量的土地资源，未经治理的废弃矿井区域普遍存在地面建筑物破旧，地下采空区安全隐患，地下、地表水体及土壤污染，环境景观恶劣等现象，局部存在引发地质灾害的危险。通过对全省范围内的废弃矿井展开系统全面调查，查明各类废弃矿井2 806处，主要集中于浙西低山丘陵区的衢州市1 442个、浙南西部山地丘陵区的丽水市509个、浙中丘陵盆地的金华市445个，占全省废弃矿井总数的85.39%，并对各类废弃矿井进行影响分析，归纳总结废弃矿井影响现状，为开展系统、全面、有针对性的治理工作提供依据。     

The effect of optimized carbon source on the synthesis and composition of exopolysaccharides produced by Lactobacillus paracasei

This study aimed to predict the optimal carbon source for higher production of exopolysaccharides (EPS) by Lactobacillus paracasei TD 062, and to evaluate the effect of this carbon source on the production and monosaccharide composition of EPS. We evaluated the EPS production capacity of 20 strains of L. paracasei under the same conditions. We further investigated L. paracasei TD 062, which showed the highest EPS-producing activity (0.609 g/L), by examining the associated biosynthesis pathways for EPS. Genomics revealed that fructose, mannose, trehalose, glucose, galactose, and lactose were carbon sources that L. paracasei TD 062 could use to produce EPS. We identified an EPS synthesis gene cluster that could participate in transport, export, and sugar chain synthesis, and generate 6 sugar nucleotides. Experimental results showed that the sugar content of the EPS produced using fermentation with the optimized carbon source (fructose, mannose, trehalose, glucose, galactose, and lactose) increased by 115%. Furthermore, use of the optimized carbon source changed the monosaccharide content of the associated EPS. The results of enzyme activity measurements showed significant increases in the activity of 2 key enzymes involved in the glycoside synthesis pathway. Our study revealed that optimizing the carbon source provided for fermentation not only increased the production of EPS, but also affected the composition of the monosaccharides by increasing enzyme activity in the underlying synthesis pathways, suggesting an important role for carbon source in the production of EPS by L. paracasei TD 062.     

Dependence of Lamellar Eutectic Growth with Convection on Boundary Conditions and Geometric Confinement: A Phase-Field Lattice-Boltzmann Study

Metallurgical and Materials Transactions B - Simulating eutectic growth with convection is challenging because of the enormous computing demand resulting from the required domain size compared with...     

Investigation of machining and wear performance of various diamond micro-grinding tools

The International Journal of Advanced Manufacturing Technology - The wear of micro-grinding tools less than 1 mm in diameter is crucial for achieving acceptable surface quality and accurate...