Characterization and challenge of development of producer gas fuel combustor: A review

Producer gas, which derived from a biomass gasification process, is considered as one of the alternative fuels, which is suitable for the heating process and power generation. Due to low heating density and impurities, combustion in an external combustion chamber constitutes an obvious option for the utilization of producer gas via the combustion process. This paper reviews the technical challenges and the development of the producer gas combustor. Various combustion techniques are reviewed. A stable flame combustion with low emissions (both CO and NO_x) constitutes a main requirement of the producer gas combustion. Flame stabilization techniques such as swirl-vane coupled with bluff-body, swirl flow configuration, and staging combustion were successfully employed to enhance the stability and performance of the producer gas combustion. As shown in the results of the studies, the combustion process can operate in a wide range of equivalence ratios with the exhaust gas temperature >600 °C. This temperature is sufficiently hot for the power generation and heating applications. Overall, NOx and CO emissions were below 700 ppm and 1.3%, respectively. In the flameless combustion mode, ultra-low emission for both CO and NOx were recorded. However, higher emission can be found when operated at a higher thermal load combustor. Homogeneity of the thermal field and low polluting emissions make flameless combustion a promising lean and clean combustion technology. Integration of the benefits of flameless combustion and producer gas fuel is an outstanding contribution in reducing emissions and enhancing the efficiency of the combustion systems.     

Durable pressure filtration membranes based on polyaniline–polyimide P84 blends

A pressure filtration membrane from conducting polymer polyaniline (PANI) is known to possess low mechanical strength and thermal stability. Therefore, it is believed that the properties of the membrane can be enhanced by blending PANI with a conventional polymer like polyimide (PI), which possesses high mechanical strength and thermal stability. A thermal analysis revealed that polymer chain of blend membranes started to break beyond the melting temperature of pure PANI membrane indicating that the addition of PI hindered the degradation of PANI and thus slowed down the decomposition process. Mechanical tests further showed that PANI/PI membrane had a tensile strength that was 60% higher than pure PANI membrane. Furthermore, the surface hydrophilicity and negativity of the blend membrane increased as it was doped in acid, thereby reflecting the exploitation of advantages of both polymers. Rejection at various molecular ranges of PEGs showed that PANI/PI membrane was initially in the ultrafiltration (UF) range, but later fell into the nanofiltration (NF) range when an acid dopant was introduced to the membrane. According to the long‐term filtration performance, the PANI/PI membrane was able to sustain a rejection of up to 99% in Congo red solution with just a slight reduction in flux. POLYM. ENG. SCI., 59:E82–E92, 2019. © 2018 Society of Plastics Engineers     

Simulation of producer gas flameless combustion with fresh reactant diluted by hot flue gas

Flameless combustion is considered as a flexible and efficient combustion process for low heating value gas fuel. This paper presents numerical simulations of premixed flameless combustion using producer gas as a fuel. Different initial conditions of the premixed fresh reactant (air/fuel mixture) and dilution levels are taken into account for the investigation. The numerical simulations were investigated using a network of chemical reactor models with the detailed reaction mechanism of GRI‐Mech 3.0. A threshold dilution level for flameless combustion fuelled by producer gas was determined. The numerical results show that dilution of the fresh reactant with hot combustion products and initial fresh reactant temperature play important roles in flameless combustion formation and its auto‐ignition behaviour, rather than equivalence ratio of the fresh reactant. In the flameless combustion regime, temperature and chemical concentrations were reduced while chemical kinetics process was decelerated, resulting in delay of the auto‐ignition process.     

Thermal Evaluation of Diesel/Hydrogen Peroxide Fuel Blend

Thermal properties of fossil fuel are the key fundamental characteristics, which can distinguish any compound as a potential fuel. The performance of diesel fuel blend along with stability and solubility parameter designs are evaluated. The results from the experimental study indicate that the increase in hydrogen peroxide (H₂O₂) amount enhances the cetane number of diesel fuel blend significantly. However, the calorific value decreases as compared to pure diesel fuel. All values performed well according to the ASTM D‐975 diesel testing method. The thermodynamics of the prepared fuel blends also revealed that substantial solubility and diesel/H₂O₂ blend stability are provided even at lower temperatures. Such blends can be used as a feasible replacement of pure diesel fuel.     

Physicochemical stability of antilisterial proteins from P. polymyxa Kp10 as potential food biopreservative

Listeria monocytogenes has continuously become a significant threat to consumers worldwide. The use of chemical-derived preservatives that are commonly associated with safety and nutritional issues has prompted the use of natural-based preservatives as a better alternative. Many bacterial strains including Paenibacillus polymyxa Kp10 have been reported to produce various antimicrobial proteins and compounds that are considered more natural. However, their stability in various physicochemical conditions should be examined before being applied in various types of food. In this study, the stability of four previously identified antilisterial proteins in P. polymyxa Kp10 upon exposure to several physicochemical conditions was examined. More than 80% residual antilisterial activity is conserved upon heat and proteinase K treatment. But, sensitivity to 24 h trypsin digestion has been observed. P1 and P2 proteins (histone-like DNA binding proteins HU) were sensitive to alkaline pH (pH 10-12) as compared with other proteins. More than 70% and 97% residual antilisterial activity were recovered after incubation in raw beef homogenates and simulated meat gravy model, respectively. However, the antilisterial activity of most proteins was highly compromised in chicken and salmon meat homogenates, and UHT cow milk. Inoculation of these proteins into Listeria-contaminated simulated meat gravy showed that all proteins exerted a bactericidal action against L. monocytogenes. P1 and P2 shared almost similar antilisterial activity rates, while P4 was the most potent antilisterial protein. The findings in this study could provide important preliminary data for future applications of these proteins as preservative in food products especially beef-based meat products.     

Compressive mechanical properties of sawdust/high density polyethylene composites under various strain rate loadings

This article is concerned with the static and dynamic mechanical properties of high‐density polyethylene (HDPE) reinforced with sawdust (SD) at a strain rate of up to 10³ s^?1. In this study, the static and dynamic properties of HDPE/SD composites with different filler loadings of 5, 10, 15, 20, and 30 wt% SD were deliberated at different levels of strain rates (0.001, 0.01, 0.1, 650, 900, and 1100 s^?1) using a conventional universal testing machine and the split Hopkinson pressure bar apparatus. The results showed that the stress–strain curves, yield behavior, stiffness, and strength properties of the HDPE/SD composites were strongly affected by both the strain rate and the filler loadings. Furthermore, the rate sensitivityof the HDPE/SD composites showed a great dependency on the applied strain rate, increasing as the strain rate increased. However, the thermal activation values showed a contrary trend. Meanwhile, for the postdamage analysis, the results showed that the applied strain rates influenced the deformation behavior of the tested HDPE/SD composites. Moreover, for the fractographic analysis at dynamic loading, the composites showed that all the specimens underwent a severe catastrophic deformation. J. VINYL ADDIT. TECHNOL., 24:162–173, 2018. © 2016 Society of Plastics Engineers     

The effect of polypropylene maleic anhydride on polypropylene/(recycled acrylonitrile butadiene rubber)/(sugarcane bagasse) composite

The effect of polypropylene maleic anhydride (PPMAH) on the tensile properties and morphology of polypropylene (PP)/(recycled acrylonitrile butadiene rubber) (NBRr)/(sugarcane bagasse) (SCB) composites has been studied. Six different composites (100/0/10, 80/20/10, 70/30/10, 60/40/10, 50/50/10, and 40/60/10), with fixed 5 wt% of PPMAH compatibilizer and without PPMAH addition, were carried out. The composites were prepared through melt‐mixing technique at 180^oC for 9 min using a rotor speed of 15 rpm. The specimens were analyzed for mechanical properties and examined with scanning electron microscopy. The tensile strength was found to decrease with increasing filler content. However, tensile strength and Young's modulus of the PPMAH compatibilized composites were found to increase, while the elongation at break showed the opposite trend as compared with the control composites. The morphology results support the tensile properties and indicated a better interaction between the SCB filler and PP/NBRr matrices with the presence of PPMAH as a compatibilizer. This is due to the esterification bonding between the SCB filler and PP matrix in the presence of PP/NBRr matrices. J. VINYL ADDIT. TECHNOL., 23:228–233, 2017. © 2015 Society of Plastics Engineers     

Contributing to Understand the Crosstalk between Brain and Periphery in Methylmercury Intoxication: Neurotoxicity and Extracellular Vesicles

Human exposure to methylmercury (MeHg) is currently high in regions such as the Amazon. Understanding the molecular changes associated with MeHg-induced neurotoxicity and the crosstalk with the periphery is essential to support early diagnoses. This work aimed to evaluate cellular and molecular changes associated with behavioral alterations in MeHg acute exposure and the possible changes in extracellular vesicles (EVs) number and S100β content. Adults male Wistar rats were orally treated with 5 mg/kg for four days. Behavioral performance, molecular and histological changes in the cerebellum, and plasma EVs were assessed. MeHg-intoxicated animals performed significantly worse in behavioral tests. MeHg increased the number of GFAP+ cells and GFAP and S100β mRNA expression in the cerebellum but no change in NeuN+ or IBA-1+ cells number was detected. The number of exosomes isolated from plasma were decreased by the metal. S100B mRNA was detected in circulating plasma EVs cargo in MeHg exposure. Though preliminary, our results suggest astrocytic reactivity is displaying a protective role once there was no neuronal death. Interestingly, the reduction in exosomes number could be a new mechanism associated with MeHg-induced neurotoxicity and plasma EVs could represent a source of future biomarkers in MeHg intoxication.