Crystallinity variations in kaolinite induced by grinding and pressure treatments

Kaolinite samples treated with uniaxial pressures higher than 0.1 GPa or grinding times greater than 0.3 h show changes in their crystallinity. These changes are easily detected by the X-ray diffraction (XRD) technique and can be quantified from Hinckley (HI), Lietard (R₂) and also reference intensity ratio (RIR) index studies. The sensitivity of these indices to the Crystallinity changes is; HI>RIR>R₂. In the range of pressures and grinding times considered, these values can be diminished by 50%. The variations in these indices with either the pressure or grinding time follow logarithmic laws whose correlation coefficients are closed to unity. Infrared (IR) spectroscopy and thermal analysis studies show low sensitivity to the changes introduced by grinding or pressure. Nevertheless, thermal gravimetric curves confirm the decrease in the dehydroxylation starting point of about 100°C for the pressed and ground samples. Transmission electron microscopy (TEM) reveals important changes in kaolinite particle morphologies after pressure and grinding treatments. The samples compressed at 0.1, 0.32, 0.85, 1.0 and 2.0 GPa show a large number of defects (fractures, bending, deformations and rolling of layers, glide and rotation of the shell). The ground samples show grain boundaries, dislocations, twins and rounded voids. These defects are responsible for the decrease in crystallinity of the kaolinite samples shown in the XRD and IR studies.     

Fast acquisition clock and data recovery circuit with low jitter

This paper presents a half-rate clock and data recovery circuit (CDR)that combines the fast acquisition of a phase selection (PS) delay-locked loop (DLL) with the low jitter of a phase-locked loop (PLL). The PLL acquisition time improves considerably with use of a phase frequency magnitude detector(PFMD) that feeds back an estimate of the magnitude of the frequency difference in addition to the sign. Measurements in 0.5/spl mu/m CMOS technology show operation up to 700 Mb/s, a 7% acquisition range, an initial acquisition time of 8 bit times with jitter of 30% bit time, and jitter of 16 ps after the PLL acquires lock. With a phase frequency detector (PFD), the PLL locks in about 700 ns from an initial frequency difference of 7%. Measurements using a PFMD show the 700 ns PLL acquisition time is reduced on average by about a factor of 5 to 140 ns from an initial 7% frequency difference. The power dissipation is 300mW.     

业务穿越ATM-PON的延时和延时变化研究

ATM-PON是光纤接入网的重要技术。文章研究了业务穿越ATM-PON接入网的延时和延时变化性能，着重分析媒体接入控制协议对业务延时和延时变化性能的影响。研究结论对ATM-PON媒体接入控制协议的合理设计有很大的帮助。     

The geometric nature of plasticity laws

This paper concerns the plasticity constitutive laws in small strain. In the thermodynamic approach developed here, the key concept is that of internal variables. The differential nature of plasticity law has been pointed out for a long time. If we unite the invariance condition of these laws in a state variable transformation, this involves, ultimately, that the natural mathematic frame of plasticity theory is Differential Geometry. The system state is defined as a point of a differentiable manifold. The state variable are the local coordinates of this point in a chart. The internal stresses are the components of a covariant vector of the cotangent bundle to internal state manifold and the elastic domain is a convex part of cotangent vector space. The plastic yield criteria such as von Mises condition define a Riemannian structure over the manifold. The metric element is identified with the internal dissipation element. Constitutive laws link the covariant derivatives of the thermodynamic stress with the state variable. Hardening modulus splits up in two parts, kinematic hardening and metric hardening. This last is defined by Christoffel connection coefficients. Applied to von Mises isotropic yield condition, the metric hardening is identified with isotropic hardening. The Baltov-Sawczuk model is also analysed. The use of appropriate polar coordinates simplifies significantly the computations. Generalization to a significant category of non-differentiable yield criteria, such as Tresca condition, is considered by introducting a metric tensor family. The adaptation of Drucker's postulate to the proposed model requires the introduction of parallel transport of the internal stress covector. Generally, this transport is different over distinctive paths joining two points. This fact expresses internal state manifold curvature. The Riemann-Christoffel tensor is computed for von Mises, Baltov-Sawczuk and Tresca models.     

On-body propagation velocity estimation using ultra-wideband frequency-domain spatial correlation analyses

On-body communications around the human torso are considered, using ultra-wideband transmissions. The velocity of the diffracted wave propagating around the body is extracted from frequency- domain spatial correlation analyses.     

Characterization of an ASIC for CPG sensors with grid-only depth of interaction sensing

A new version of the front-end application specific integrated circuit (ASIC) for co-planar-grid (CPG) sensors is presented. Compared to the first version, the ASIC is optimized for signal/noise performance, modified in peaking time, and it implements timing signals to measure the depth of interaction using the grids signals only. Experimental results using state-of the-art CPG sensors and different approaches for reducing the error due to electron trapping are reported. A new technique that makes use of the sum and difference of the grids signals is also presented.     

Detection of failure sites by focused ion beam and nano-probing in the interconnect of three-dimensional stacked circuit structures

Focused ion beam (FIB) and nano-probing were applied for failure analysis of three-dimensional stacked circuits with copper through-silicon-vias between the stacked chips. The failure analysis was done after high temperature storage and thermal cycling tests. Passive voltage contrast in FIB allowed to pinpoint the open sites. FIB cross-sections showed the presence of opens at the bottom of the copper vias. The failure cause was suspected to be an interlayer particle, which was confirmed by optical profilometry. Nano-probing was used on another sample to pinpoint the failure location through the measurement of the local resistance within the daisy chains. The failure was traced out to be related with surface contamination.     

Shape-Controlled Synthesis and Upconversion Luminescence of Y2O3:Yb, Er Microstructures

The Y2O3: Yb3 , Er3 microstructures were fabricated by a hydrothermal method without surfactants.The microstructures structure was characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM,KYKY 1000B).The up-conversion luminescence spectra were studied under 978 nm laser diode excitation.In Yb3 and Er3 codoped Y2 O3 microcrystals, the relative intensity of green emission became stronger as the morphology of sample changed from wires to films.