Rational Designs for Lithium-Sulfur Batteries with Low Electrolyte/Sulfur Ratio

Lithium-sulfur batteries (LSBs) are considered a promising next-generation energy storage device owing to their high theoretical energy density. However, their overall performance is limited by several critical issues such as lithium polysulfide (PS) shuttles, low sulfur utilization, and unstable Li metal anodes. Despite recent huge progress, the electrolyte/sulfur ratio (E/S) used is usually very high (≥20 µL mg⁻¹), which greatly reduces the practical energy density of devices. To push forward LSBs from the lab to the industry, considerable attention is devoted to reducing E/S while ensuring the electrochemical performance. To date, however, few reviews have comprehensively elucidated the possible strategies to achieve that purpose. In this review, recent advances in low E/S cathodes and anodes based on the issues resulting from low E/S and the corresponding solutions are summarized. These will be beneficial for a systematic understanding of the rational design ideas and research trends of low E/S LSBs. In particular, three strategies are proposed for cathodes: preventing PS formation/aggregation to avoid inadequate dissolution, designing multifunctional macroporous networks to address incomplete infiltration, and utilizing an imprison strategy to relieve the adsorption dependence on specific surface area. Finally, the challenges and future prospects for low E/S LSBs are discussed.     

Improved Corrosion Resistance of Selective Laser Melted Ti–5Cu Alloy Using Atomized Ti–5Cu Powder

The different types of metal powder used for selective laser melting(SLM) process would cause distinct corrosion behavior due to the uniformity of the obtained microstructure.The SLM-produced Ti–5Cu alloy using atomized Ti–5Cu metal powder(SLMed Ti–5Cu) in this work reveals a relatively uniform microstructure with overwhelming acicular α/α′ phase and shows great advantages on corrosion resistance compared with the SLM-produced Ti–5Cu alloy using the mixture powder(SLMedM Ti–5Cu).The effect of the micro-galvanic cells decreases due to the undetectable Ti_2Cu phase in the microstructure of the SLMed Ti–5Cu.An apparent passivation behavior was observed for SLMed Ti–5Cu instead of severe pitting phenomenon for the SLMed-M Ti–5Cu.The charge transfer resistance of SLMed Ti–5Cu in this work is 10.09 ± 2.63 MΩ cm~2, which is significantly higher than that of SLMed-M Ti–5Cu(4.76 MΩ cm~2).The above result indicates the atomized Ti–5Cu powder plays an important role in the formation of the uniform microstructure of SLMed product, thereby enhancing its corrosion resistance in Hank's solution at 37 ℃.     

气瓶内部淬火过程的流动换热特性

 大直径厚壁气瓶内部淬火时的流动换热过程极其复杂，受到多种因素的影响，而研究气瓶内部压强和温度的变化规律对改善流动换热效果、提高产品组织性能具有重要的理论指导意义。以914 mm厚壁气瓶和瓶内流体为研究对象，建立了二维等效流 固耦合模型；采用多喷嘴系统对气瓶内外进行喷水淬火，研究了气瓶总长、喷水流速及淬火时间对瓶内压强及内壁温度的影响，通过间歇淬火试验验证了数学模型的正确性。结果发现，气瓶长度对瓶内压强和瓶壁温度的影响显著，喷水流速次之，当喷水流速大于8 m/s后，水量对瓶壁的冷却效果大大降低；气瓶内壁长度方向的温度梯度分别随气瓶总长的增加和淬火时间的延长而减小，但基本不受喷水量的影响。     

Simulation Analysis of the Heat Transfer Performance of an N-type Microchannel Heat Exchanger

A microchannel heat exchanger with a triangular wave and symmetrical triangular wave structure was proposed in this paper. In addition, a new N-type microchannel heat exchanger was developed to balance the heat transfer performance and pressure drop. The relationship between different configurations of the N structure of the microchannel and the heat transfer performance was analyzed. The results showed that, at a high inlet flow rate, the symmetrical triangular wave microchannel had the best heat transfer performance, followed by the triangular wave microchannel and the straight channel. At the same flow rate, the degree of disturbance of the fluid was highest in the symmetrical N-structure microchannel, and an excellent heat transfer effect was observed.     

两阶段领域自适应学习

针对领域自适应问题中源域和目标域的联合分布差异最小化问题,提出两阶段领域自适应学习方法.在第一阶段考虑样本标签和数据结构的判别信息,通过学习一个共享投影变换,使投影后的共享空间中边缘分布的差异最小.第二阶段利用源域标记数据和目标域非标记数据学习一个带结构风险的自适应分类器,不仅能最小化源域和目标域条件分布差异,还能进一步保持源域和目标域边缘分布的流形一致性.在3个基准数据集上的实验表明,文中方法在平均分类准确率和Kappa系数两项评价指标上均表现较优.     

食物成瘾的研究进展及启示

食物成瘾是一种复杂的慢性疾病，导致人们在日常生活中对某种食物产生过度依赖与过度进食等相关行为特征，近年来已被认为是影响欧美发达国家肥胖症、暴食症、糖尿病等发病率持续升高的关键原因，引起学术界的极大关注，成为研究热点。本文主要介绍食物成瘾的概念、诊断标准，综述了食物成瘾的病理机制、影响因素和应对措施等方面的研究进展，并探讨食物成瘾对我国食品界的启示，为预防食物成瘾，保障公众健康提供有益借鉴。     

Lead-free sodium niobate nanowires with strong piezo-catalysis for dye wastewater degradation

In this work, the hydrothermally-synthesized sodium niobate nanowires were used to decompose Rhodamine B dye solution through the piezo-catalytic effect. With the sodium niobate catalyst, a high piezo-catalytic degradation ratio of ～80% was achieved under the excitation of vibration for the Rhodamine B dye solution (～5?mg/l). These active species in the catalytic process, hydroxyl radicals and superoxide radicals with the strong oxidation ability, were also observed, which confirmed the key role of piezoelectric effect for piezo-catalysis. The piezo-catalysis of sodium niobate nanowires provides a high-efficiency and reusable tool in application in depredating the dye wastewater.     

再生玻璃作为辅助胶凝材料制备ECC的力学及变形性能

为考察再生玻璃作为辅助胶凝材料对ECC的影响,开展了一系列力学性能试验,研究其抗折与抗压强度、弯曲性能和单轴拉伸性能.结果 表明:采用再生玻璃作为辅助胶凝材料可显著提高ECC的抗压强度,同时抗折强度略有降低;再生玻璃作为辅助胶凝材料或细骨料制备的ECC在弯曲荷载下可呈现出明显的多缝开裂和假应变硬化特征;通过良好的配合比设计,再生玻璃粉仅作为辅助胶凝材料制备的ECC平均极限拉伸应变接近3％,具备良好的变形能力.