沥青延度与流变特性关系研究分析(一)

通过对两种基质沥青进行不同温度及不同速率下的延度试验，找出它们的流变特性，并从微观上进行分析，最后与路用性能相联系，又通过TFOT试验找出流变特性对耐老化性之间的关系，最后得出，沥青的流变特性可通过延度试验来表征，它能够较好地反映沥青的路用性能。     

苯磺隆干悬浮剂技术浅析

通过对苯磺隆干悬浮剂项目的研究,进一步了解干悬浮剂的加工工艺和配方中各种助剂的相互作用;剖析助剂对主要技术指标的影响。     

A STUDY ON ACIDITY AND CATALYTIC PROPERTY OF [B] ZSM-5 CATALYST MODIFIED WITH SILICON COMPOUND BY CHEMICAL SURFACE DEPOSITION OF LIQUID-PHASE TECHNIQUE

The boron heteroatom zeolite catalyst has been modified with silicon compound by Chemical Surface Deposition of Liquid-phase (CLD) technique and the catalytic property of the modified catalyst is studied. Meanwhile, the acidity of the modified zeolite catalysts is characterized through TPD and IR technique, and the fluid adsorption method is used to determine its pore structure. The relationship between the catalytic property of the zeolite catalyst and its pore structure, its acidity has been found. The results of toluene-ethylene alkylation reaction indicate that the selectivity of p-ethyltoluene on the modified zeolite catalyst is higher than that on the zeolite catalyst before silanizated, reaching 94.14%.     

线性二次型最优控制闭环系统极点的必要条件

本文推导了线性二次型（LQ）最优控制闭环系统极点应满足的必要条件，以及与加权阵Q和R的等式关系     

APT（STLRI）—1.78型单模光纤（缆）连接器简介

利用引进的制造技术和设备,制作出了 APT(STLRI)—1.78型系列化光纤连接器。     

磷矿的电选试验研究

清水沟中低品位磷矿性质复杂，嵌布粒度细，磨至-0．174mm 92．8％，通过振动—气流联合作用摩擦荷电，采用悬浮电选机经-粗-精-扫电选。可由含P2O5为24．47％的原矿获得含P2O5为30．23％。回收率为83．26％，杂质含量合格的磷精矿。     

Enhanced light output in nitride-based light-emitting diodes by roughening the mesa sidewall

In this letter, we will report on a nitride-based light emitting diode with a mesa sidewall roughening process that increases light output power. The fabricated GaN-based light-emitting diode (LED) wafers were first treated through a photoelectrochemical (PEC) process. The Ga/sub 2/O/sub 3/ layers then formed around the GaN : Si n-type mesa sidewalls and the bottoms mesa etching regions. Selective wet oxidation occurred at the mesa sidewall between the p- and the n-type GaN interface. The light output power of the PEC treated LED was seen to increase by about 82% which was caused by a reduced index reflectance of GaN-Ga/sub 2/O/sub 3/-air layers, by a rough Ga/sub 2/O/sub 3/ surface, by a microroughening of the GaN sidewall surface, and by a selective oxidation step profile of the mesa sidewall that increases the light-extraction efficiency from the mesa sidewall direction. Consequently, this wet PEC treated process is suitable for high powered nitride-based LEDs lighting applications.     

A new method for producing high melt strength polypropylene with reactive extrusion

A high‐melt‐strength polypropylene (HMSPP) was prepared using a twin‐screw reactive extruder from a commercial isotactic polypropylene through two stages, first, maleic anhydride is grafted to polypropylene to obtain a maleic anhydride‐grafted polypropylene (PP‐g‐MA), and then the grafted polymer is reacted with epoxy to extend the branched chain. Fourier transformed infrared spectroscopy indicated that maleic anhydride was grafted on polypropylene and reacted with epoxy. Melt flow rate and sag resistance test showed that the melt strength of the HMSPP improved considerably. Differential scanning calorimetry test showed that the long chain branches (LCBs) act as a nucleating agent in the crystallization of the HMSPP, which leads to a high crystallization temperature and crystallinity. Furthermore, the LCB efficiency of the HMSPP can also be calculated by analyzing its rheological property. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers