Durability of radiation-sterilized polymers III. Oxidation layer determined by chemiluminescence

Chemiluminescence (CL) analysis was used for determining the oxidation layer formed by the irradiation of polypropylene for medical supplies. The depth of the oxidation layer from the surface depended on dose rate and increased with decreasing dose rate. The oxidation occurred remarkably at a region near the surface area of the film where the diffusion of oxygen is more sufficient. On the contrary, there was very little oxidation in the interior portion. The oxidation layers of polypropylene samples irradiated with electron beam showed U-shaped profiles in the cross-section of film as did as a sample irradiated with γ-rays. However, the degree of oxidation by irradiation with electron beam was very small; CL intensity at the surface area was only one-third that for the γ-irradiated samples.     

Ring hydrogenation of naphthalene and 1-naphthol over supported metal catalysts in supercritical carbon dioxide solvent

Catalytic ring hydrogenations of naphthalene and 1-naphthol were studied over several supported metal catalysts in supercritical carbon dioxide solvent at low temperature. Higher concentration of hydrogen in supercritical carbon dioxide and lower reaction temperature were responsible for higher catalyst activity and selectivities to the desired partial ring hydrogenated products as compared with those observed in organic solvent for the same catalyst.     

Highly Reactive β-Dicalcium Silicate: III, Hydration Behavior at 40–80°C

The effect of curing temperature (40°, 60°, 80°C) on the hydration behavior of β-dicalcium silicate (β-C₂S) was investigated. The β-C₂S was obtained by decomposition of hillebrandite, Ca₂(SiO₃)(OH)₂, at 600°C, has a specific surface area of about 7 m²/g, and is in the form of fibrous crystals. The dependence of the hydration reaction on temperature continues until the reaction is completed. The hydration is completed in 1 day at 80°C and in 14 days at 14°C. The hydration mechanism is different above and below 60°C, but at a given temperature, the reaction mechanism and the silicate anion structures of C-S-H do not change significantly from the initial to the late stages of the reaction. High curing temperature and long curing times after completion of reaction promote silicate polymerization. The Ca/Si ratio of C-S-H shows high values, being almost 2.0 above 60°C and 1.95 below 40°C.     

Recoverable shear strain of liquid crystal‐forming concentrated hydroxypropyl cellulose solutions

The recoverable shear strain (S_R) for the liquid crystal‐forming hydroxypropyl cellulose solutions was determined by means of a concentric cylinder rotational apparatus as functions of shear stress prior to recovery and concentration of the solutions at 30°C. S_R greatly depended on shear stress and concentration; the phase of the solution (the single phase or biphase) governed the dependences of S_R on stress and concentration. S_R increased with increasing stress for the single phase and decreased for the biphase. S_R seemed to be related to the die swell (B): S_R ∝ Bⁿ. S_R exhibited a maximum and a minimum with respect to concentration. S_R for the cellulosic cholesteric liquid crystalline solutions was greater than that for the isotropic solutions. A model was proposed for explaining the greater S_R. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 865–872, 2002     

In Situ Observation of Zirconia Particles at 1200°C by High-Resolution Electron Microscopy

Zirconia (ZrO₂) particles (average diameter, 30 nm) were observed in an in situ heating experiment up to 1200°C using a 400-kV high-resolution electron microscope. Thermal vibration of atoms on a (001) surface plane was observed at 1100°C. At 1200°C, grain growth and sintering phenomena were recorded on a videotape, showing (100) lattice planes migrating on a surface of a particle. Direct observation of the sintering process on a lattice level was accomplished for the first time.     

The effect of sputter etching on the surface characteristics of dyed aramid fabrics

Three kinds of aramid fabrics, Technora (modified p-aramid), Conex (m-aramid) and Kevlar (p-aramid), were subjected to sputter etching and argon low-temperature plasma treatments after dyeing in black with disperse dyes. The depth of shade increased considerably on Technora and Kevlar with the sputter etching treatment, but not on Conex fabrics. Argon low-temperature plasma treatment had virtually no effect on the depth of shade on the aramid fabrics.     

Graft polymerization of some vinyl monomers onto acrylic rubber. II. Mechanical properties of graft polymers

Some mechanical properties of styrene and acrylonitrile copolymers grafted onto acrylic rubber are investigated. The impact strength of graft polymers depended upon the nature and the concentration of the catalyst, the composition and the intrinsic viscosity of the rubber, and the acrylonitrile content in the rigid matrix. The most desirable result was obtained when benzoyl peroxide as the catalyst, n-butyl acrylate–acrylonitrile copolymer of 7–10% acrylonitrile content, and about 0–5% acrylonitrile in the rigid matrix were used. Dynamic mechanical tests show the increase in efficiency of rubber modification by the grafted chains. The better weathering resistance of these graft polymers, as compared with commercial ABS plastics, was confirmed.     

Synthesis of Compositionally Homogeneous Sr(CuxZn1−x)1/2W1/2O3

A complex perovskite of Sr(Cu _x Zn_{1- x} )_1/2 W_1/2O₃ (SCZW) is synthesized by a new combination of wet and dry processess. Mixed oxides containing Cu²⁺ and Zn²⁺ (CZ) are prepared by the wet process (coprecipitate method). SCZW is obtained by the dry process (mixed-oxide method) from a mixture of CZ, SrCO₃, and WO₃. SCZW has practically no compositional, unlike solid solutions prepared by the conventional dry method. The wet–dry process method is useful because the wet process is applied to only B-site cations having the same valence.     

Development of a high‐resolution RGBW flexible display using a white organic light‐emitting diode with microcavity structure and that of a side‐roll touch panel

In this study, white organic electroluminescent devices with microcavity structures were developed. A flexible high‐resolution active‐matrix organic light‐emitting diode display with low power consumption using red, green, blue, and white sub‐pixels formed by a color‐filter method was fabricated. In addition, a side‐roll touch display was developed in combination with a capacitive flexible touch screen.     

High thermal stable thermoplastic-thermosetting polyimide film by use of asymmetric dianhydride (a-BPDA)

In order to obtain thermoplastic (before curing) and thermosetting (after curing) polyimides with high T_g for adhesive film, we prepared novel polyimides having phenylethynyl group in the side chain (44% of concentration of curing group) from asymmetric 2,3,3′,4′-biphenyltetracarboxylic dianhydride (a-BPDA), 3,4′-oxydianiline (3,4′-ODA) or 1,3-bis(4-aminophenoxy)benzene (1,3,4-APB) or 1,3-bis(3-aminophenoxy)benzene (1,3,3-APB), and 2,4-diamino-1-(4-phenylethynylphenoxy)benzene (mPDAp). Among three kinds of polymer, uncured polyimide of a-BPDA/1,3,4-APB; mPDAp had rather high T_g (265 °C, DMA) and thermoplasticity (E′ drop>10³ at T_g). After curing reaction of phenylethynyl group, the T_g of the polyimide was increased dramatically (364 °C, DMA). The polyimide derived from 1,3,4-APB having less concentration of curing group (20%) was also prepared to improve further film flexibility and toughness.