Wavelength and Waveband Assignment for Ring Networks Based on Parallel Multi‐granularity Hierarchical OADMs

In this paper we study the optimization issues of ring networks employing novel parallel multi‐granularity hierarchical optical add‐drop multiplexers (OADMs). In particular, we attempt to minimize the number of control elements for the off‐line case. We present an integer linear programming formulation to obtain the lower bound in optimization, and propose an efficient heuristic algorithm called global bandwidth resource assignment that is suitable for the design of large‐scale OADM networks.     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.     

井下套管阀研究及室内试验

随着欠平衡钻井技术的深入研究和推广应用,全过程欠平衡钻井技术已成为研究热点。除了常规的欠平衡装备外,全过程欠平衡钻井还需配备井下套管阀,为此,研制了一种双液控井下套管阀。为检验该阀的使用可靠性,进行了全面的室内试验和测试,试验内容包括压力密封能力,高压、有流动情况下阀板关闭的动作准确性,模拟现场阀板下憋压时打开阀板的作业程序,检测在各种密封压力时阀的微泄漏量。试验结果表明,该阀达到设计要求,能够满足全过程欠平衡作业的工艺要求。     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。     

无油分子泵机组的组装

介绍了将ALCATEL公司生产的一台ATPl00涡轮分子泵、一台MDP50ll牵引分子泵及一台VRC公司生产的lBy6型干泵组装成无油分子泵机组的过程。文中给出了泵间配合的计算、机组方案的设计、连接管路、仪器支架的设计及选择。本机组所采取的设计方案使三个泵都最大限度地发挥了优点避免了缺陷，较好地满足了使用要求，为今后选购单泵和组装无油分子泵机组提供了可靠的理论和实验依据。     

深井长裸眼跨隔测试新工艺的应用

为减少勘探费用，缩短施工周期，取全取准各项地质资料，采取中途测试工艺。随着深井中途测试不断增多，特别是跨隔支撑测试具有一定施工风险和难度，要求测试质量不断提高。结合油田生产实际，合理选配了地层测试工具仪表，不断改进测试管串和优化施工设计，经盐22井中途跨隔测试应用，获得成功。     

Mobility management architectures based on joint mobile IP and SIP protocols

In the all-IP wireless networks beyond the third generation, mobility management can be effectively achieved by applying mobile IP (MIP) and the session initiation protocol (SIP) jointly. Nevertheless, an efficient combination of both protocols remains an open research issue. Conventional hybrid MIP-SIP mobility architectures operate MIP and SIP almost independently, resulting in significant redundant costs. This article investigates the representative hybrid MIP-SIP architectures and explores the joint optimizations between MIP and SIP for a more cost-efficient mobility support whilst utilizing their complementary power. Two novel design approaches are presented. The first approach culminates in a tightly integrated architecture, which merges the redundant mobility entities in MIP and SIP to yield maximum system efficiency. The other approach leads to a loosely integrated architecture, where necessary interactions are introduced between MIP and SIP mobility servers while their physical entities are kept intact. Major mobility procedures, including location update, session setup and handoff, are discussed in these architectures. The analytical results demonstrate that both proposed architectures outperform typical hybrid MIP-SIP architectures in terms of clear-cut reduced signaling costs     

不同注F剂量与CMOS运放电路辐照损伤的相关性

在不同注F剂量条件下,对P沟和N沟两种不同差分对输入CMOS运放电路的电离辐照响应进行了研究.分析比较了注F和未注F运放电路电离辐照响应之间的差异.结果表明,在栅场介质注入适量的F,可有效抑制辐照感生的氧化物电荷尤其是界面态的增长,从而提高CMOS运放电路的抗辐照特性.     

下一代无线通信概念和技术

下一代无线通信(NextG:Next-generationwireless)的主流是随时随地的无线通信系统和无缝的高质量无线业务。概述了随时随地的无线通信和业务发展情况,并且介绍了为下一代无线通信的发展提供基础的关键技术。