聚苯醚磺酸锂／共聚醚复合物的离子导电性研究

合成了３种不同磺化度的聚苯醚磺酸锂（ＳＰＰＯＬｉ）与Ｐ（ＭＥＯ１６－ＡＭ）／ＳＰＰＯＬｉ复合物。研究了复合物的离子导电性与磺化度，组成比及增塑剂含量的关系。含４０％（ｍａｓｓ）增塑剂的复合物具有单离子导电特征，锂离子迁移数高达０．９７，室温电导率达２×１０－５Ｓ／ｃｍ。     

两个重组质粒在快生型大豆根瘤菌中的稳定性的比较

将两个复制子相同的重组质粒导入快生型大豆根瘤菌中，考察了得到的转移接合子在培养和共生条件下的稳定性。发现带有质粒ＲＫ２ ｐａｒ基因的重组质粒ｐＴ２ＴＸ３Ｋ在快生型大豆根瘤菌中无论在培养还是共生条件下都可以稳定存在，而不带有该基因的重组质粒ｐＣＫ３在两种条件下都有一定程度的丢失。     

使用混合杆柱时抽油泵柱塞的超冲程

任何抽油杆柱在理论上都可能产生超冲程，只是大小不同而已。超冲程的存在，使泵柱塞的有效冲程增大，甚至会大于光杆冲程。首次提出了抽油泵柱塞相对超冲程和绝对超冲程的概念，这将有助于正确认识玻璃钢抽油杆的作用和玻璃钢抽油杆的推广使用。将抽油杆柱简化成上端受光杆的激振位移、下端带有集中质量的弹簧－质量力学模型，建立了抽油杆柱纵向振动的偏微分方程和边界条件，然后用固有函数法求解方程，得出了抽油泵柱塞超冲程的无穷级数解析计算式。     

基于非线性规划的指数自回归模型的辨识

讨论了指数自回归模型的辨识问题，证明了该模型最小二乘估计的目标函数的非凸性，并给出了使该函数为凸的条件，最后给出了辨识该模型的算法及该算法的收敛性，并以数值例子加以说明。     

Growth and characterization of hot-wall epitaxial CdTe on (111) HgCdTe and CdZnTe substrates

Thin CdTe films were deposited by hot-wall epitaxy (HWE) on (111) HgCdTe and CdZnTe substrates at temperatures from about 140 to 335°C. X-ray rocking curves were used to show that crystal quality of the CdTe (111)B films improved as substrate temperature increased from 140 to about 250°C. Rocking curve values for full width at half maximum (FWHM) decreased from 2–4 degrees at 140–150°C to less than 100 arc-s at 250°C, and a FWHM of 59 arc-s was the lowest value observed near 250°C. The FWHM of the HWE CdTe was found to be insensitive to growth rate below about 400Å/min, but increased to four degrees at 1250Å/min. X-ray diffraction confirmed that films grown on the B-face at higher temperatures were epitaxial, but contained a significant volume fraction, 35% to 50%, of rotational in-plane twins. Electron microscopy confirmed a coarse twin density, and photoluminescence spectra showed an absence of excitonic emission in the HWE films. Simultaneous growth on two (111) HgCdTe substrates with different surface polarities between 230°C and 335°C showed that deposition rate on the A-face decreased relative to that on the B-face as temperature increased. Films grown on the B-face exhibited better surface morphologies than those grown on the A-face.     

泥沙起动条件及机理的非线性研究

 分析了单颗粒、均匀沙及非均匀沙的起动现象及其机理，认为泥沙的起动属于突变论研究的范畴。从泥沙起动所遵循起动条件的力学规律出发，导出泥沙起动条件方程。在此基础上，利用尖点突变性质对各种泥沙起动现象及机理进行了描述和说明。     

银矿尾矿砂高强陶粒的研制

以广西凤凰银业有限公司的尾矿砂和废矿页岩为主要原料，在前期工作的基础上，经过实验室试验和生产线中试，成功生产出700～1000密度等级、筒压强度超过10MPa的高强陶粒。这为银矿的尾矿砂和废矿页岩的处理也为我国高强陶粒的生产探索了一条新路。     

Feasibility study on the use of polyallyldiglycol-carbonate cell dishes in TUNEL assay for alpha particle radiobiological experiments

In the present work, we have studied the feasibility of a method based on polyallyldiglycol-carbonate (PADC) films to investigate the effects of alpha particles on HeLa cervix cancer cells. Thin PADC films with thickness of about 20 μm were prepared from commercially available CR-39 films by chemical etching to fabricate custom-made petri dishes for cell culture, which could accurately record alpha particle hit positions. A special method involving “base tracks” for aligning the images of cell nuclei and alpha particle hits has been proposed, so that alpha particle transversals of cell nuclei can be visually counted. Radiobiological experiments were carried out to induce DNA damages, with the TdT-mediated dUTP Nick-End Labeling (TUNEL) fluorescence method employed to detect DNA strand breaks. The staining results were investigated by flow cytometer. The preliminary results showed that more strand breaks occurred in cells hit by alpha particles with lower energies. Moreover, large TUNEL positive signals were obtained even with small percentages of cells irradiated and TUNEL signals were also obtained from non-targeted cells. These provided evidence for the bystander effect.     

GCr15轴承钢的热变形模拟试验研究

利用先进的Gleeble-2000热模拟试验机，对GCr15轴承钢某一轧制过程进行模拟试验，测定出GCr15轴承钢动态CCT曲线，并结合微观组织分析，制定合理的GCr15轴承钢轧后控制冷却工艺，以期达到提高GCr15轴承钢质量的最终目的。     

韶钢第三炼钢厂2#板坯连铸机漏钢原因分析

针对韶钢三炼钢板坯连铸机的漏钢原因从设备与工艺上进行分析,提出整改措施,对韶钢以后的板坯发展提供了经验.