Selective catalytic reduction of nitric oxide by propane over vanadia-titania aerogels

An investigation has been carried out of the effect of vanadia loading on the activity and selectivity ofV₂O₅TiO₂ aerogel catalysts, prepared by a two-step procedure, for the reduction of NO by propane. The structure of catalysts have been characterized by laser Raman spectroscopy and XRD measurements. At vanadia loading levels below ca. 4.4 wt%, the vanadia is present in the form of coordinated polymeric species, whereas crystallites of V₂O₅ are formed at higher vanadia contents. At this critical level of 4.4 wt% V₂O₅, the kinetic measurements showed also a maximum in the activity per mass of catalyst which very likely indicated that the coordinated polymeric surface species are more active than crystalline V₂O₅. The selectivity towards the formation of dinitrogen decreased as the loading increased, presumably because of the formation of larger polymeric species and V₂O₅ crystallites, below and above the critical loading level, respectively. For the reduction of NO by propane, titania supported vanadia aerogel catalysts are significantly more active, per mass of catalyst, and more selective towards N₂ formation than conventionalV₂O₅TiO₂ and V₂O₅Al₂O₃ aerogel catalysts, at vanadia loading levels below ca. 11 wt%.     

Reactivity of steam in exhaust gas catalysis III. Steam and oxygen/steam conversions of propane on a Pd/Al2O3 catalyst

A 1% Pd catalyst (38% dispersion) was prepared by impregnating a γ-alumina with palladium acetylacetonate dissolved in acetone. The behaviour of this catalyst in oxidation and steam reforming (SR) of propane was investigated. Temperature-programmed reactions of C₃H₈ with O₂ or with O₂ + H₂O were carried out with different stoichiometric ratios S(S =[O₂]/5[C₃H₈]). The conversion profiles of C₃H₈ for the reaction carried out in substoichiometry of O₂ (S < 1) showed two discrete domains of conversion: oxidation at temperatures below 350°C and SR at temperatures above 350°C. The presence of steam in the inlet gases is not necessary for SR to occur: there is sufficient water produced in the oxidation to form H₂ and carbon oxides by this reaction. Contrary to what was observed with Pt, an apparent deactivation between 310 and 385°C could be observed with Pd in oxidation. This is due to a reduction of PdO_x into Pd⁰, which is much less active than the oxide in propane oxidation. Steam added to the reactants inhibits oxidation while it prevents the reduction of PdO_x into Pd⁰. Compared to Pt and to Rh, Pd has a higher thermal resistance: no deactivation occurred after treatment up to 700°C and limited deactivation after treatment up to 900°C, provided that the catalyst is maintained in an oxygen-rich atmosphere during the cooling.     

橡塑共混热塑性弹性体的形态结构与性能

综述了影响共混热塑性弹性体的形态结构与性能的主要因素。     

单分散六边形扁平溴碘化银微晶的结构与性能的研究

应用可控双注仪制备了一系列碘含量相同而碘在微晶中分布不同的单分散六边形扁平溴碘化银乳剂。用扫描电镜（ＳＴＥＭ）与Ｘ－射线能谱仪（ＥＤＳ）对单个微晶进行了微区分析，并用介电损耗，微波光导等方法研究了此类乳剂微晶的结构与性能的关系。结果表明：严格控制微晶成核、成熟、生长三个阶段的条件，可制得含六边形颗粒９２％以上的扁平溴碘化银乳剂，颗粒大小变化系数小于１２％。此外碘在微晶中的分布明显影响微晶的电性质和     

壳聚糖／聚丙烯酸钠聚离子复合膜的醇－水渗透汽化分离性能

研究了壳聚糖－醋酸溶液与聚丙烯酸钠溶液形成的复合膜用于水－乙醇混合物的渗透汽化分离，在膜组成Ｃ＝０．８０时，分离系数出现最大值，对异丙醇－水体系的分离系数为∞。溶解－扩散过程对渗透汽化过程起着重大作用。由－ＮＨ＋３…ＯＯＣ－交联的聚离子复合膜对醇－水体系具有稳定的分离性能。     

现代汽车活塞制造技术总论

本文针对现代汽车活塞的生产技术特点,综述了制造技术及其装备的主要课题,重点分析介绍非圆裙面加工、异型销孔精镗、工艺基准的关键作用,变形对加工精度的影响,检测技术配套及全面提高铸件质量等关键问题的国内外发展动向。     

贝利阀在氨厂运行情况简介

介绍贝利阀在试车及试生产期间出现的问题及解决办法，指出维护过程中应注意的事项。     

国产活性炭在合成气净化中的应用

选择国产Ｋ０１活性炭脱除羰基铁、镍，以达到保护铑催化剂并减少副产物的目的。１年的实际应用结果表明：国产Ｋ０１活性炭能够替代进口活性炭在合成气净化中应用。     

可编程控制器在化肥散运系统上的应用

整个散运系统采用３台ＦＸ２－１２８ＭＲＰＬＣ分块控制后，使得控制结构清楚，线路简单，工作可靠性大为提高，对所有控制柜元器件进行数据库管理，极大地提高图表的准确率。     

电子自旋共振在橡胶研究中的应用

综述了电子自旋共振在橡胶的合成、加工和应用领域的应用现状及其发展前景。