双季戊四醇在3种混合溶剂中的固-液相平衡

采用动态平衡法，在293.15～332.80 K、常压下，测定了双季戊四醇(DPE)在水+(甲醇、乙醇、异丙醇)三种混合溶剂中的溶解度数据。结果表明：DPE在不同质量分数的水+(甲醇、乙醇、异丙醇)混合溶剂中的溶解度随体系温度升高而增大；同一温度下，其在所选取溶剂体系中的溶解度随着甲醇、乙醇或异丙醇质量分数的增大而先增大后减小。λh方程、两参数方程与Apelblat方程均能够对所测定的溶解度数据进行较好的关联；通过修正的van’t Hoff方程计算得到DPE在所选取溶剂体系中Δ_sol H ⁰、Δ_sol S ⁰和Δ_sol G ⁰均大于零，表明DPE在所选取溶剂体系中的溶解过程为吸热、熵增的非自发过程。     

三种硫化氢吸收剂吸收效率对比及碘酸钾体系吸收条件优化研究

硫化氢具有腐蚀性与毒性，采用吸收剂吸收硫化氢气体是重要的脱硫处理方式。不同的吸收剂在吸收效率上存在较大差别。首先对比了三氯化铁体系、碘酸钾体系和碱性铁氰化钾体系三种不同硫化氢吸收剂的吸收效率。在此基础上重点优化了碘酸钾体系吸收条件参数，讨论了包含浓度、温度、pH、气体流量及时间等因素对硫化氢吸收效率的影响。并建立了四因素三水平正交试验研究较优吸收条件，得到正交试验优化吸收条件为：温度55℃，pH 6.01，硫化氢流量0.3 L·min^-1，吸收时间1 min，该条件下8%（质量）碘酸钾体系的三级吸收效率为51.56%。研究结果对硫化氢吸收处理提供了理论参考，也为间接电解法循环处理研究提供了支持。     

A mini review on two-dimensional nanomaterial assembly

Two-dimensional (2D) nanomaterials have attracted a great deal of attention since the discovery of graphene in 2004, due to their intriguing physicochemical properties and wide-ranging applications in catalysis, energy-related devices, electronics and optoelectronics. To maximize the potential of 2D nanomaterials for their technological applications, controlled assembly of 2D nanobulding blocks into integrated systems is critically needed. This mini review summarizes the reported strategies of 2D materials-based assembly into integrated functional nanostructures, from in-situ assembly method to post-synthesis assembly. The applications of 2D assembled integrated structures are also covered, especially in the areas of energy, electronics and sensing, and we conclude with discussion on the remaining challenges and potential directions in this emerging field.

     

Research on optimization design of PWR flow distribution device based on numerical simulation

ABSTRACT

In the lower chamber of pressurized water reactor (PWR), the flow distribution device is the core module to distribute coolant into the core. It has complex structure and numerous design parameters. Therefore, it has important theoretical and practical significance to optimize the device. The mesh independence verification, turbulence model selection, and data processing all can influence the numerical simulation results of the lower chamber, in order to research the influence, a numerical simulation method based on the original model of CNP1000 reactor lower chamber is proposed in this paper. In the method, an optimization design method of flow distribution device is established based on surrogate model. The main design variables and optimization objectives are determined based on the device’s structure and function characteristics. And then it respectively adopts Kriging algorithm and multi-objective genetic algorithm to establish a surrogate model of flow distribution device and optimize it globally. Finally, the optimal design variables are obtained. Compared with the device’s performance before optimization, the after optimization has smaller total pressure loss and more uniform flow. The effectiveness and practicability of proposed optimization design method can be verified.     

Influence of Sodium Microalloying on Rolling Contact Endurance and Mechanical Properties of Hot-Deformed Powder Steels

Russian Journal of Non-Ferrous Metals - Rolling bearing rings comprise a large reserve for expanding powder metallurgy production. This reserve is being incompletely implemented. The hot forging of...     

MPE: a mobility pattern embedding model for predicting next locations

World Wide Web - The wide spread use of positioning and photographing devices gives rise to a deluge of traffic trajectory data (e.g., vehicle passage records and taxi trajectory data), with each...