Regeneration characteristics of desiccant rotor with microwave and hot-air heating

Microwave heating, because of its advantages of direct and rapid heating of materials, has the potential to be employed as a novel regeneration method of desiccant rotors in humidity conditioners. We proposed a combined regeneration process, which combines microwave heating and conventional hot-air heating. The system is expected to achieve high heating rate during an initial regeneration period by assisting water desorption using the additional energy of the microwave. In this study, the regeneration characteristics of a desiccant rotor were experimentally investigated under conditions of microwave heating, hot-air heating, and combined heating at various microwave powers and hot-air temperatures. The effectiveness of the combined regeneration was evaluated in terms of the regeneration ratio, the initial regeneration rate, the temperature distribution in the rotor, and finally in terms of the energy consumption. It was demonstrated that combined heating was effective at leveling non-uniform temperature distribution in the rotor. Combined heating achieved higher ratios and initial rates in regeneration compared to just microwave and hot-air heating. This result was obviously attributed to the additional input of microwave energy, resulting that average rotor temperature increased by microwave absorption of rotor. Moreover, it was also effective for enhancement of regeneration to level the temperature distribution in the rotor by combination of two heating methods with different heating mechanisms. Both the initial regeneration rate and the equilibrium regeneration ratio for combined heating were found to increase as the microwave power increased. A linear relationship was observed with respect to microwave power. From the viewpoint of energy consumption, it may be possible to apply combined and microwave heating to humidity control systems that switch between adsorption and regeneration in short cycle times, if the conversion and absorption efficiencies of the microwave are significantly improved.     

Thermosetting bismaleimide resins generating covalent and multiple hydrogen bonds

Prepolymerizations of 4,4′‐bismaleimidodiphenylmethane (BMI), diallyl isocyanurate (DAIC), and melamine (ML) at 160–170°C and subsequent compression molding at 200–280°C yielded cured BMI/DAIC/ML resins with feed molar ratios of 4/1/1, 3/1/1, and 2/1/1 (BMI‐DAIC‐ML411, 311, and 211). Similarly, cured BMI/DAIC 1/1 and BMI/ML 3/1 resins (BMI‐DAIC11 and BMI‐ML31) were prepared. The FT‐IR analysis revealed that the maleimide and allyl groups were almost consumed for all the cured resins, and the hydrogen bonding interaction became stronger with decreasing BMI contents for BMI‐DAIC‐MLs. Based on the cured structures elucidated from the FT‐IR result, the numbers of multiple hydrogen bonds and cross‐linking covalent bonds (N_MHB and N_CB), and total cross‐linking bond energy (E_TB) were evaluated to be 0, 7.92, and 618 for BMI‐DAIC‐ML411, 0.71, 7.81, and 627 for BMI‐DAIC‐ML311, and 0.95 mol kg^?1, 7.61 mol kg^?1, and 617 kcal kg^?1 for BMI‐DAIC‐ML211, respectively. A higher order of glass transition and 5% weight loss temperatures for BMI‐DAIC‐MLs was 411 > 311 > 211 in accordance with a higher order of N_CB. BMI‐DAIC‐MLs displayed a weak tan δ peak at 70–150°C due to dissociation of the hydrogen bonds. The flexural strength and modulus of BMI‐DAIC‐ML311 were higher than those of BMI‐DAIC‐ML411 in accordance with the difference of E_TB. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43121.     

Nickel‐Catalyzed Suzuki–Miyaura Coupling of a Tertiary Iodocyclopropane with Wide Boronic Acid Substrate Scope: Coupling Reaction Outcome Depends on Radical Species Stability

We describe a nickel‐catalyzed Suzuki–Miyaura arylation of a tertiary iodocyclopropane with arylboronic acids; this is an efficient and convergent strategy for providing various enantioenriched arylcyclopropanes with a quaternary stereogenic center. This is the first metal‐catalyzed coupling between a tertiary alkyl electrophile and a wide range of aromatics, including heteroaromatics. We found that the outcome of the Ni‐catalyzed coupling with halides as electrophiles was dependent on the stability of the radical species formed during the reaction. The use of tert‐butyl alcohol (t‐BuOH) as the reaction solvent was very effective, because of its stability under the radical‐generating reaction conditions.

     

Acoustic emission sources of breakdown failure due to pulsed-electric discharge in concrete

Acoustic emission (AE) technique is applied to locate existing breakdown failure in concrete. Damage was generated in a concrete sample applying 6.4 kJ energy of pulsed-electric discharge. Both AE parameter analysis and waveform analysis were carried out. From results of AE parameter analysis, AE sources associated with existing breakdown failure were identified in the compression test. Prior to location analysis, AE waveforms detected were de-noised by employing the wavelet transform. The area of breakdown failure in concrete is identified by the source location analysis of these de-noised AE waveforms. Five locations of breakdown failure are found in the concrete sample. Micro-cracks occur starting from the lower part of concrete sample and then spread randomly in entire concrete body.     

Effect of temperature on friction observed between a Si3N4 tip and a dodecanethiol self-assembled monolayer on Au(1 1 1)

Recent computational studies (Phys. Rev. Lett. 70 (1993) 1960; Phys. Rev. B 62 (2000) 17055) predicted that friction of ordered organic monolayer had characteristic dependence on temperature, where the maximum friction was observed around rotator transition point of the monolayer. This remained to be confirmed experimentally. Using a friction force microscope (FFM) combined with a temperature regulation module, we attempted to investigate such dependence on temperature (130 K-room temperature) on a self-assembled monolayer of dodecanethiol prepared on Au(1 1 1). The observed friction showed strong dependence on temperature and good agreement with the computational prediction.     

Dietary CLA and DHA modify skin properties in mice

This study investigated the influence of PUFA on the properties of mouse skin. Mice (3 wk old) were given free access to oils high in linoleic acid, CLA, or DHA for 4 wk. At the end of the experiment, their skins were compared by both biochemical and histological methods. No significant differences in lipid and collagen contents were detected among treatments, although the FA composition in the skin was altered depending upon the FA composition of the supplemented oils. Electron microscopy revealed that the subcutaneous tissue layers in the CLA and DHA groups were significantly thinner than that in the high linoleic acid group, whereas no differences in the thickness of dermis layers were observed among the three groups. These results suggest that skin properties in mice are readily modified by dietary FA sources within 4 wk of dietary oil supplementation.     

Polarization state fixer composed of passive optical devices

We investigate a polarization state fixer that produces light with an arbitrary desired polarization state and constant power from an arbitrary elliptically polarized input light whose principal polarization axis fluctuates randomly. An example of such a device composed of a quarter-wave plate and a polarizer is proposed, and its characteristics at wavelengths of 633 nm and 1550 nm are demonstrated. We conclude that we cannot obtain a passive device that produces fixed-axis, linearly polarized light with a constant power level from an elliptically polarized light with a varying elliptical parameter.     

Mask design compensation for sloped sidewall structures fabricated by X-ray lithography

We have investigated and report in this paper the factors influencing the deformation caused by the dependence between the absorbed X-ray energy on the resist and the shape of the absorber on the X-ray mask. Based on the measurement of errors that occurred during the transferring process between the 2-D shape of mask pattern and the resulting wall of the fabricated 3-D structure, we have developed newly useful graphical data on the absorbed X-ray energy, dosage, and shape of a microstructure. As a result, it is being reported as a method for compensation for the deformed shape after the fabrication of a quadruplets-microneedle. We have considered a number of factors affecting the deformation and finally realized that the effect of a dose–depth nonlinear curve is the most possible cause. Without the compensation of the mask design, we could observe the deformed shapes of the sloped sidewall on the exposed structures. Polymethylmethacrylate microneedle structures fabricated by X-ray lithography with an additional plane-pattern to cross-section transfers technique are directly influenced by the absorber on the X-ray mask pattern. The sidewall of the microneedle was improved by changing the mask pattern from a double right-triangular pattern to a double semi-circular pattern, modeled by comparing the results from a mask-pattern and the actual structure.