长期暴露的海工混凝土性能与显微结构分析

在青岛市黄岛区海边防波堤的潮差区和浪溅区钻取多个Φ100mm的混凝土试样.采用氯离子滴定仪、pH计、扫描电子显微镜、EDAX等仪器对氯离子分布、混凝土的碳化情况和微观结构形态进行了研究.结果表明:潮差区和浪溅区混凝土表层的总氯离子含量差不多,但相对于潮差区,浪溅区混凝土的总氯离子含量具有较陡的下降斜率和较大的部分碳化区及pH值变化范围.浪溅区混凝土表面细骨料裸露,潮差区混凝土表面细骨料部分裸露和混凝土结构疏松,且有絮状物覆盖在表面并含有大量的C,O以及N元素.浪溅区表层混凝土的氯离子扩散系数比潮差区混凝土的大,但距表面4.0cm时潮差区混凝土的氯离子扩散系数超过浪溅区.混凝土表面腐蚀严重,并有微生物或微生物代谢产物,覆盖在混凝土的表面.     

电化学除氯处理后的混凝土微观结构研究

为了研究电化学除氯对混凝土中离子分布和微观结构的影响规律,采用压汞法、SEM电子显微镜分析等方法对电化学除氯后不同水灰比混凝土试件中钢筋附近和表面层的氯离子和钾钠离子含量、孔隙结构、显微结构进行对比分析.结果显示,电化学除氯后,钢筋附近混凝土与外层混凝土相比,氯离子含量约为1/2,钾离子含量约为5～10倍,钠离子含量约为8～18倍,水化物颗粒间结合不连续、部分水化产物分解.钢筋附近区域混凝土中的氯离子含量明显低于外表层混凝土,钾、钠离子在钢筋阴极附近大量聚集.经过电化学处理后的混凝土试件钢筋附近区域的孔隙率和大孔含量增多,结构疏松;而外表层混凝土结构致密,孔隙细化,水化产物成网络状结合良好.     

Wrinkling of epoxy powder coatings

Differential scanning calorimetry (DSC) and mechanical profilometry were used to study wrinkle formation in curing epoxy powder coatings. Powder coating formulations were studied that contained solid epoxy resins, methylene disalicylic acid (MDSA) crosslinker, and an amine‐blocked Lewis acid catalyst. Both the crosslinker (MDSA) and the amine‐blocked catalyst are required for wrinkle formation. Evaporation of the blocking amine from the free surface of the coating generated a depthwise gradient in the extent of polymerization and crosslinking, and hence in the degree of solidification, as evidenced by the formation of a mechanical skin prior to wrinkling. It is hypothesized that compressive elastic stress develops in the still swellable skin when unreacted low‐molecular‐weight material from beneath diffuses up into the monomer‐ or oligomer‐depleted crosslinking skin and swells it. This compressive stress, if above a critical value, buckles the skin to produce wrinkles. Experimentally observed compositional requirements for wrinkle formation were consistent with the proposed mechanism. The size of the wrinkles can be controlled by varying formulation parameters such as the amount of catalyst or crosslinker. Increasing the amount of catalyst decreased both the wavelength and the amplitude of the wrinkle pattern. Increasing the amount of crosslinker initially increased the amplitude of the wrinkles; after reaching a maximum level, the wrinkle amplitude decreased. DSC was a useful tool to understand the critical reactions responsible for wrinkling in this system. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 116–129, 2005     

新型多单体接枝物增容PP/PVC共混体系的研究

自制了多单体接枝物PP g (St co MMA) ,并利用其增容PP/PVC共混体系。讨论了共混物组成、相容剂用量在不同温度、不同压力下对其流变行为的影响。实验结果表明 ,在所研究的温度和压力范围内 ,加入PP g (St co MMA)增容PP/PVC共混体系后 ,共混物熔体呈典型的假塑性流体特性 ,粘流活化能增加 ,非牛顿性有增大的趋势。共混体系的力学性能提高 ,SEM照片证明了多单体接枝物对PP/PVC的增容作用     

Visible light localization algorithm based on multi-measurements constraints

In the indoor visible light transmission environment with complex noise, traditional received signal strength indication(RSSI)localization algorithm and imaging localization algorithm are unable to accurately determine the reason of the inaccurate localization model and inadequate constraints of position coordinates. In order to solve the problems, a visible light localization algorithm based on multi-measurements constraints is presented in the paper. The algorithm first constructs a joint localization state space model based on RSSI localization and the imaging localization algorithm. Then, states, measurements and their equations are constructed based on the space model. Finally, the equations are resolved using the unscented Kalman filter(UKF). Compared with RSSI localization and imaging localization, simulation results show that the RMSE of the proposed algorithm could be closer to the Cramer Rao bound. Besides, the localization probability of the proposed algorithm is higher than that of RSSI localization and imaging localization algorithm.     

Effect of glass removal on the GMI effect of Co71.8Fe4.9Nb0.8Si7.5B15 amorphous glass-covered wires

During the past several years, giant magneto-impedance effect (GMI) in amorphous wires has generated growing interest in the science community because of theirapplications in sensors. The giant magneto-impedance effect in Co71.8Fe4.9Nb0.8Si7.5B15 amorphous glass-covered wires (AGCW) consists of strong changes in the high frequency impedance with a small DC magnetic field. When f =1 MHz, there is no GMI effect due to the fact that the magnetic penetration depth is higher than their radius. As the frequency increases, the GMI effect becomes important in both the glass-covered wire and the wire afterglass removal. Field dependence of the impedance has a similar behaviour to the AGCW ones, when a tensile stress is applied to the wire without glass cover.     

硼离子注入对多晶Ni力学性能及微观结构的影响

用能量为50keV,剂量为3×10~(17)ions/cm_2的B~+注入多晶Ni,通过力学性能实验研究了多晶Ni注入前后表面硬度和疲劳性能的变化,以及多晶Ni表面层注入和疲劳前后化学成分、滑移特征、裂纹萌生、断裂方式和微观结构的变化。结果表明,B~+注入多晶Ni后,表面区域形成一个不同组织结构的由Ni-B非晶、Ni_3B和Ni_4B_3第二相以及辐照损伤组成的多层次的注入层,提高了多晶Ni的表面硬度,并使其疲劳极限提高16％。探讨了B~+注入影响多晶Ni疲劳极限的几种可能机制。     

Effect of solid fraction on steel-mushy Cu-graphite pressing bonding

The pressing bonding of steel plate to QTi3.5-3.5graphite slurry was studied. The bonding conditions were 620℃ for preheating temperature of steel plate, 530℃ for preheating temperature of dies, 50 MPa for pressure and 2 min for pressing time. The relationship between the solid fraction of QTi3.5-3.5graphite slurry and the interracial mechanical property of bonding plate was obtained. The results show that when the solid fraction of QTi3.5-3.5graphite slurry is smaller than 45.8%, the interracial shear strength of bonding plate increases with the increasing of solid fraction. When the solid fraction is larger than 45.8%, the interracial shear strength decreases with the increasing of solid fraction. When the solid fraction is 45.8%, the largest interracial shear strength of bonding plate 127 MPa can be got, and the interface is made up of Fe-Cu solid solution.     

38CrSi钢表面纳米结构层力学性能的研究

采用超音速微粒轰击技术在38CrSi合金钢表面制备了厚度约为25μm纳米晶层.利用X射线衍射、扫描电镜和透射电镜对表面结构进行分析.纳米结构层的最表面层的晶粒尺寸约为16nm,晶粒尺寸随着距表面距离的增加而增大.利用纳米压痕仪对表面纳米结构层的力学性能进行研究,结果表明,当表面晶粒尺寸降低到纳米量级时力学性能明显改善,最表面纳米结构层的硬度是基体的2倍左右,并服从Hall-Petch关系;表面纳米结构层的弹性恢复系数明显提高;利用该方法制备的纳米晶对弹性模量的影响较小;对表面纳米化样品进行低温退火处理可使纳米结构层的性能更加稳定.分析表明表面纳米结构层力学性能的改善主要是表面晶粒细化的结果.     

四辊轧机轧辊弹性变形解析模块的开发

采用影响函数方法开发了四辊轧机轧辊弹性变形解析模块，完善了辊间压扁和工作辊压扁影响函数计算模型，克服了轧辊压扁影响函数计算过程浮点数被零除的缺陷，提出了平滑指数和收敛指标取值的处理方法，有效地解决了四辊轧机辊系弹性变形计算精度及收敛问题。该模块适应于普通四辊轧机、PC轧机和CVC轧机轧辊弹性变形计算，为热轧带钢板形控制提供了解析工具。