Antioxidative effect of Ajowan in a model system

Model conditions were utilized to test the antioxidative activity of a methanolic extract of ajowan (Carum coptimum) (MEA). MEA was less effective than butylated hydroxytoluene in protecting against oxidation of emulsified linoleic acid measured by coupled oxidation of linoleic acid-β-carotene, conjugated diene values, and the thiobarbituric acid values. Ajowan may have potential as a source of natural antioxidant.     

Dual segment rectangular dielectric resonator antenna with metamaterial for improvement of bandwidth and gain

The simulation and experimental studies of an aperture‐coupled wideband dual segment rectangular dielectric resonator antenna with metamaterial for C‐band applications are presented in this paper. The antenna consists of Alumina (Al₂O₃) ceramic as upper segment and Teflon as lower segment. The combination of circular‐shaped coplanar split‐ring resonator and conducting strip has been used as metamaterial superstrate. With the use of metamaterial superstrate, the bandwidth of the antenna is increased by 48% through simulation and 22% experimentally. The broadside radiation pattern of the antenna is converted into directive radiation pattern with reduced beamwidth when metamaterial superstrate is used. The peak gain of the antenna is also enhanced by 33% through simulation and 31% experimentally with the use of metamaterial superstrate. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:646–655, 2014.     

Limits of compensation in a failed antenna array

In large antenna arrays, the possibility of occurrence of faults in some of the radiating elements cannot be precluded at all times. In such situations, the radiation pattern of the array gets distorted, mostly with an increase in sidelobe level and decrease in gain. Although it is not possible to restore the pattern fully by rearranging the excitations of the functioning elements, compensation methods have been reported in the literature for restoring one performance parameter of the array and making a trade‐off on some other parameter. In this article, we have made a study on the tolerance level of this compensation process. One part of the study deals with the thinning in the failed array, that is, to find a limit on the minimum number of functioning elements of the array that can restore the digital beamforming of the failed array. The second part of study deals with finding the maximum number of element failures that can be compensated. The study was carried out by optimizing the amplitude excitations of the failed array. Instead of classical optimization techniques, particle swarm optimization was used for the compensation process. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:635–645, 2014.     

Targeting and design of water networks for fixed flowrate and fixed contaminant load operations

Water-using processes are typically modeled as either fixed flowrate operations or fixed contaminant load operations. A new method for targeting the minimum freshwater and pinch in a single-contaminant water network is proposed, which can be applied to both kinds of operations. The method consists of plotting separate source and demand composites with flowrate as the horizontal axis and contaminant load unusually as the vertical axis. It is elegant, non-iterative, and can handle hybrid problems where both kinds of operations coexist.To design minimum freshwater networks for fixed flowrate problems, an algorithm is presented based on a newly developed principle of nearest neighbors. The principle simply states that the source streams to be chosen to satisfy a particular water demand must be the nearest available neighbors in terms of contaminant concentration.To design minimum freshwater networks for fixed contaminant load problems, the nearest neighbors algorithm is applied to process units that lie across the pinch. Units that lie entirely on one side of the pinch are satisfied by the cleanest source available on that side of the pinch. In other words, below-pinch units are satisfied by freshwater and above-pinch units are satisfied by the cleanest available stream above the pinch. Designs based on this methodology, apart from meeting the minimum freshwater target, also minimize the water flowing through the process units resulting in reduced network capital cost.     

Performance evaluation of saponin over other organic acid and tap water for removal of chromium in tannery sludge by electrokinetic enhancement

The performance of Saponin over different electrolyte-mediated electrokinetic (EK) process for removal of Cr(III) from tannery sludge was assessed. Saponin exhibited maximum Cr(III) removal efficiency, i.e. 67.6–80.75% as compared to other groups of processing fluids. The possible mechanistic approach for the highest removal efficiency of saponin over other electrolytes may be attributed to synchronized effect of micelle formation and subsequent complexation and sorption of chromium ions. The highest electroosmotic flow rate of saponin indicated low electroosmotic resistance during EK process, which validates the observed trend. Therefore, saponin can be considered as a promising electrolyte for EK treatment of tannery sludge.

Abbreviation: CA: Citric acid; LA: lactic acid; OA: oxalic acid; BOD: biochemical oxygen demand; COD: chemical oxygen demand; EK: electokinetic.     

Mass transfer between solid particles and liquid in a three phase fluidized bed

Particle-liquid mass transfer in a co-current three-phase fluidized bed of glass beads, water and air was studied with two measurement techniques. Both techniques measured the weight loss of a few particles coated with benzoic acid in a bed of inert glass beads. The effects of liquid and gas velocities, gas distribution and surface active agents on particle-liquid mass transfer in a three-phase fluidized bed were thus determined. In the absence of surface active agents in the liquid, particle-liquid mass transfer rates in a three-phase fluidized bed were up to 30% higher than in the corresponding liquid fluidized bed. When surface active agents were added to the liquid, the particle-liquid mass transfer rate was increased by up to about 100% in the three-phase fluidized bed, relative to the liquid fluidized bed. The particle-liquid mass transfer coefficient was found to be inversely proportional to the liquid hold-up in the three-phase fluidized bed.     

Direct contact heat transfer between two immiscible liquids during vaporization: Part II: Total evaporation time

A dilatometric technique was used to determine the total evaporation time of individual drops of furan, isopentane and cyclopentane as they rose in water. The values of total evaporation time were predicted reasonably well for each system by a different equation than was used to correlate the evaporative data for the initial 10% of the evaporative process as reported in Part I of this study. The total evaporation time data were also compared with the correlations given by Klipstein ⁽¹⁾, by Sideman and Taitel ⁽²⁾ and with the correlation which was found by the authors to best fit the total evaporative data for the three systems. In agreement with Klipstein ⁽¹⁾, the correlation for the overall heat transfer coefficient was found to be one of the form, q_A = Cd₁^2.0δt. The rate of rise of an evaporating drop for the conditions used in this study was found to be nearly equal to the instantaneous terminal velocity.     

Modal analysis of prestressed draft pad of freight wagons using finite element method

The present work intends to investigate dynamic behaviour of draft gear using finite element method. The longitudinal force that the draft gear absorbs usually leads to the failure of its components, especially, the load bearing draft pads. Dynamic behaviour of an individual draft pad and a draft gear is determined and characterized with exciting frequencies and corresponding mode shapes. The effect of compressive prestress load on the dynamic behaviour of an individual draft pad is also determined as the draft pads in assembled state are under constant axial compressive force in the draft gear. The vibration characteristics of individual draft pad are compared with draft pads that are part of draft gear. The modal analysis gives us a basis for subjecting a draft pad to higher frequency loading for determining its fatigue behaviour.

     

Improving delamination resistance of carbon fiber reinforced polymeric composite by interface engineering using carbonaceous nanofillers through electrophoretic deposition: An assessment at different in-service temperatures

In this article, modification of carbon fiber surface by carbon based nanofillers (multi-walled carbon nanotubes [CNT], carbon nanofibers, and multi-layered graphene) has been achieved by electrophoretic deposition technique to improve its interfacial bonding with epoxy matrix, with a target to improve the mechanical performance of carbon fiber reinforced polymer composites. Flexural and short beam shear properties of the composites were studied at extreme temperature conditions; in-situ cryo, room and elevated temperature (−196, 30, and 120°C respectively). Laminate reinforced with CNT grafted carbon fibers exhibited highest delamination resistance with maximum improvement in flexural strength as well as in inter-laminar shear strength (ILSS) among all the carbon fiber reinforced epoxy (CE) composites at all in-situ temperatures. CNT modified CE composite showed increment of 9% in flexural strength and 17.43% in ILSS when compared to that of unmodified CE composite at room temperature (30°C). Thermomechanical properties were investigated using dynamic mechanical analysis. Fractography was also carried out to study different modes of failure of the composites.     

Effects of fiber surface grafting by functionalized carbon nanotubes on the interfacial durability during cryogenic testing and conditioning of CFRP composites

Carbon fiber reinforced epoxy (CE) composite is ideal for a cryogenic fuel storage tank in space applications due to its unmatched specific strength and modulus. In this article, inter-laminar shear strength (ILSS) of carbon fiber/epoxy (CE) composite is shown to be considerably improved by engineering the interface with carboxyl functionalized multi-walled carbon nanotube (FCNT) using electrophoretic deposition technique. FCNT deposited fibers from different bath concentrations (0.3, 0.5, and 1.0 g/L) were used to fabricate the laminates, which were then tested at room (30°C) and in-situ liquid nitrogen (LN) (−196°C) temperature as well as conditioning for different time durations (0.25, 0.5, 1, 6, and 12 h) followed by immediate RT testing to study the applicability of these engineered materials at the cryogenic environment. A maximum increment in ILSS was noticed at bath concentration of 0.5 g/L, which was ~21% and ~ 17% higher than neat composite at 30°C and − 196°C, respectively. Short-term LN conditioning was found to be detrimental due to developed cryogenic shock, which was further found to be compensated by cryogenic interfacial clamping upon long-term exposure.