亚波长光栅用于实现宽光谱消色散1/4波片的研究

基于严格耦合波理论 ,分析了共振区域矩形位相光栅的衍射特性 :位相延迟与光栅周期、占空比、槽深的关系 ,并设计出在 40 0～ 80 0nm范围内的消色散 1/4波片光栅 ,可以实现较为平坦的衍射效率和位相延迟曲线 ,其中位相延迟可保持在 90°左右 ,最大偏差小于 9% ,达到甚至优于普通二元复合消色散波片。通过对加工及安装误差的讨论 ,得到了影响消色散波片光栅性能的主要加工误差是槽深误差和占空比误差。     

Structure, properties, and thermal stability of nanocrystallite Fe-Ti-N soft magnetic films

We deposited Fe-Ti-N magnetic films with a high sputtering power of 7 W/cm/sup 2/. When the composition of the films was in the range of Fe-Ti(3.9 at.%)-N(8.8 at.%) to Fe-Ti(3.3 at.%)-N(13.5 at.%), the films were composed of /spl alpha/' and Ti/sub 2/N precipitates. With the addition of nitrogen, 4/spl pi/M/sub s/ became higher than that of pure iron, reaching a maximum of 23.8 kG. At the same time, H/sub c/ was reduced to a minimum of 1.12 Oe. The best films can meet the needs of the recording head in dual-element giant magnetoresistive/inductive heads, yielding high storage density (10 Gb/in/sup 2/). The incorporation of N in /spl alpha/-Fe brought about the /spl alpha/' phase with its higher saturation magnetization. Ti additions inhibited the equilibrium decomposition /spl alpha/'/spl rarr//spl alpha/+/spl gamma/'. Because H/sub C//sup D//spl prop/D/sup 6/, where D is average grain diameter, grain size control is very important. The nitrogen induces severe distortion of the /spl alpha/' lattice, which can cause the grains to break into pieces and reduce the grain size. High sputtering power also led to the formation of fine grains, with diameter in the order of 14 nm. Probably Ti/sub 2/N is preferentially precipitated on the grain boundary, pinning the grain boundary and stabilizing the grain size during high-temperature heat treatment. The temperature limit for stability of the structure and its associated low coercivity was not less than 520/spl deg/C.     

铌和钨对γ-TiAl基合金热稳定性的影响

采用光学显微镜(OM)，扫描电镜(SEM)，X射线衍射研究了TiAl—5Nb，TiAl—14．3Nb，TiAl—8Nb—1W，TiAl—12．3Nb-2W四种合金片层组织在1000℃的热稳定性。结果表明，TiAl—12．3Nb-2W合金热稳定性最好，但合金元素对TiAl基合金热稳定性的影响机理还有待进一步的研究。     

片式多层陶瓷微波谐振器

介绍了片式陶瓷微波谐振器的工艺过程、谐振器的结构以及结构对谐振器参数的影响,谐振器与外电路的耦合采用耦合间隙的方法与谐振单元在同一层内实现,这种新结构既可给制备工艺带来方便,又可减少工艺所带来的误差。用多层陶瓷工艺技术,用高介电常数、低温烧结微波陶瓷实现了中心频率为1GHz,有载品质因数大于80的试验双端口多层微波谐振器。微波谐振器体积小,整个谐振器的尺寸为7mm×2mm×1mm,适用于表面贴装技术。     

Analysis and optimization of DS-CDMA systems with time-limited partial response chip waveforms

Conventional direct sequence code division multiple access systems (DS-CDMA) using offset quadrature phase shift key (OQPSK) usually employ a strictly bandlimited partial response square-root raised cosine pulse as the chip waveform. They have the disadvantage of large envelope fluctuation that will incur performance degradation due to the intermodulation and bandwidth enlargement caused by post nonlinear processing. To improve the performance of DS-CDMA systems, the chip waveform and receiver should be properly selected. This paper presents a systematic performance analysis of a matched filter receiver and zero-forcing filter (ZF) receiver for DS-CDMA using a time-limited partial response chip waveform. Nevertheless the systematic performance analysis is applicable to bandlimited chip pulse as well. For the zero-forcing filters, we propose to select the frequency responses that satisfy the first Nyquist criterion. With this class of filters, we can choose the roll-off factor to minimize the total power of multiple access interference and noise power. The zero-forcing filter with proper choice of roll-off factor, referred to as optimum ZF, yields a performance better than the matched filter counterpart. The bit error rate (BER) performance of the optimum ZF with superposed quadrature amplitude modulation signal as the time pulse waveform is evaluated. It is shown that the optimum ZF provides better BER performance than conventional OQPSK and minimum shift keying, and its envelope uniformity is much better than that of OQPSK.     

低阻VDMOSFET的优化设计与制造

文章对9926型双N沟增强型VDMOSFET进行了结构和版图的优化设计。给出了该器件的纵横向结构参数,材料的物理参数和版图总体结构。单胞结构的优化设计使单胞密度达到204万个/cm2,比国际市场现有产品的单胞密度(156万个/cm2)提高了30%。这种设计采用浅n+注入工艺可使器件生产成本下降31%。最后对研制结果进行了分析讨论。     

超临界流体萃取技术生产重交通道路沥青的研究

研究了采用超临界流体萃取技术(SFEF),以减压渣油和催化裂化油浆为原料,制备重交通道路沥青产品的可行性.结果表明:当原料中油浆掺入量为10%～30%时,可以生产出牌号为AH70,AH90,AH110的重交通道路沥青产品.工业试验表明,生产牌号为AH70,AH90的重交通道路沥青,采用此技术方案是可行的.     

Performance and Commercial Application of the Promoter LCC-A for Maximization of Propylene Yield

1 Introduction Propylene as an important feedstock for organic chemicals is mainly originated from steam cracking and catalytic cracking processes. During the FCC process the propylene content varies with the FCC catalyst and process technology adopted, resulting in significant difference in propylene concentration in the cracked product——LPG. The conventional FCC pro- cess generally gives a propylene yield of around 4%, while the FCC process with maximization of propylene yield can in…     

XMAC纵波时差高分辨率处理方法

在充分调研阵列声波测井分波提取方法的基础上，针对阿特拉斯公司的交叉多极子阵列声波测井（XMACⅡ）提供的单极波形信息，研究纵波时差提取及高分辨率处理方法。首先利用相关-互功谱法高精度地提取纵波时差，然后针对XMACⅡ仪器的接收阵列，研究组合子阵列的方法，形成共发射子阵列和共接收子阵列，最后利用子阵列对提取的纵波时差做高分辨率处理。处理现场实际测井资料，并将高分辨率处理成果与引进的eXpress软件处理成果、实测的国产高分辨率声波（纵波）测井曲线及岩心纵波时差对比分析，表明该方法提取的纵波时差曲线的纵向分辨率有很大提高，时差计算准确可靠，提取的单极纵波时差与国产高分辨率声波时差及岩心纵波时差的平均相对误差均小于7%。该方法具有较高的实用价值和广阔的应用前景。