An Optimized Combination of Mine Water Control,Treatment, Utilization,and Reinjection for Environmentally Sustainable Mining: A Case Study

This paper presents a case study of an optimized combination of mine water control, treatment, utilization and reinjection to achieve the zero discharge of mine water. Mine water has been considered a hazard and pollution source during underground mining, so most mining enterprises directly discharge mine water to the surface after simple treatment, resulting in a serious waste of water. Moreover, discharging a large amount of mine water can destroy the original groundwater balance and cause serious environmental problems, such as surface subsidence, water resource reduction and contamination, and adverse impacts on biodiversity. The Zhongguan iron mine is in the major groundwater source area of the Hundred Springs of Xingtai, which is an area with a high risk of potential subsidence. To optimize the balance between mining and groundwater resources, a series of engineering measures was adopted by the Zhongguan iron mine to realize mine water control, treatment, utilization, and reinjection. The installation of a closed grout curtain has greatly reduced the water yield of deep stopes in the mine; the effective sealing efficiency reaches 80%. Nanofiltration membrane separation was adopted to treat the highly mineralized mine water; the quality of the produced water meets China’s recommended class II groundwater standard. Low-grade heat energy from the mine water is collected and utilized through a water-source heat pump system. Finally, zero mine water discharge is realized through mine water reinjection. This research provides a beneficial reference for mines with similar geological and hydrogeological conditions to achieve environmentally sustainable mining.

     

Fabrication and joining mechanism of Nano-Cu/Si3N4 ceramic substrates

A novel method for fabricating a nano-Cu/Si₃N₄ ceramic substrate is proposed. The nano-Cu/Si₃N₄ ceramic substrate is first fabricated using spark plasma sintering (SPS) with the addition of nanoscale multilayer films (Ti/TiN/Ti/TiN/Ti) as transition layers. The microstructures of the nano-Cu metal layer and the interface between Cu and Si₃N₄ are investigated. The results show that a higher SPS temperature increases the grain size of the nano-Cu metal layer and affects the hardness. The microstructure of the transition layer evolves significantly after SPS. Ti in the transition layer can react with Si₃N₄ and with nano-Cu to form interfacial reaction layers of TiN and Ti–Cu, respectively; these ensure stronger bonding between nano-Cu and Si₃N₄. Higher SPS temperatures improve the diffusion ability of Ti and Cu, inducing the formation of Ti₃Cu₃O compounds in the nano-Cu metal layer and Ti₂Cu in the transition layer. This study provides an important strategy for designing and constructing a new type of ceramic substrate.     

Feasibility study of large-scale mass customization 3D printing framework system with a case study on Nanjing Happy Valley East Gate

At present, the development and implementation of digital transformation are the keys to promoting high-quality industry development. The new digital fabrication method of robotic 3D printing is a research area being studied by many to tackle the issue of the declining productivity of traditional construction methods. Although many studies have been done, most of the current 3D printing projects are facing limitations in terms of scale. In order to bridge the gap, this article proposed a mass customization 3D printing framework system for large-scale projects. This article discusses how mass customization is made possible through the joint operation of the FUROBOT software and 3D printing hardware. By taking the east gate of Nanjing Happy Valley Plaza as a case study, the article demonstrates and studies the feasibility of the large-scale mass customization 3D printing framework system.     

基于TRNSYS的茯砖茶生产工艺能源系统节能环保特性研究

茯砖茶发酵、干燥过程中，烘房内温湿度稳定性和能源系统低能耗是保证茯砖茶品质与成本的重要因素。本文采用TRNSYS仿真与实验研究相结合的方法，对咸阳某茯砖茶厂实际使用的空气源热泵系统进行建模，通过研究各季节典型代表月烘房温湿度的波动情况，确定该空气源热泵系统在全年的运行状态是否满足工艺要求，在此基础上，对比了该系统在全年可运行季节代表月与该生产厂房早期使用的燃气锅炉系统的能耗仿真结果，对空气源热泵系统的节能与环保特性进行研究。结果表明：由于夏季送风质量流量过大且室外空气含湿量较高，7月烘房温湿度不满足工艺要求。热泵系统在1、4、10月的总标煤消耗量的平均值是锅炉系统的44.42%，平均CO2、SO2、NOx排放量分别为锅炉系统的34.13%、44.1%、40.60%。在茯砖茶发酵、干燥的过程中，相比于燃气锅炉系统，空气源热泵系统具有更好的节能与环保特性。     

One step method of structure engineering porous graphitic carbon nitride for efficient visible-light photocatalytic reduction of Cr(Ⅵ)

Porous g-C3N4 nanosheets (PCN) were prepared by the nickel-assisted one-step thermal polymerization method.Hydrogen (H2) which was produced by the reaction between nickel (Ni) foam and ammonia (NH3) defined the structure and properties of PCN.During the formation of PCN,the participation of H2 not only enhanced the spacing between layers but also boosted the specific surface area that more active sites were exposed.Additionally,H2 promoted pores formation in the nanosheets,which was beneficial to the transfer of photons through lamellar structure and improved the absorption efficiency of visible light.Remarkably,the obtained PCN possessed better Cr(Ⅵ) photocatalytic reduction efficiency than pure g-C3N4.The reaction rate constant (k) of PCN (0.013 min-1) was approximately twice that of bare g-C3N4 (0.007 min-1).Furthermore,the effects of original pH and concentration of Cr(Ⅵ)-containing solution on removal efficiency of Cr(Ⅵ) were explored.A possible photocatalytic mechanism was proposed based on the experiments of radical scavengers and photoelectrochemical characterizations.     

Generating Questions Based on Semi-Automated and End-to-End Neural Network

With the emergence of large-scale knowledge base, how to use triple information to generate natural questions is a key technology in question answering systems. The traditional way of generating questions require a lot of manual intervention and produce lots of noise. To solve these problems, we propose a joint model based on semi-automated model and End-to-End neural network to automatically generate questions. The semi-automated model can generate question templates and real questions combining the knowledge base and center graph. The End-to-End neural network directly sends the knowledge base and real questions to BiLSTM network. Meanwhile, the attention mechanism is utilized in the decoding layer, which makes the triples and generated questions more relevant. Finally, the experimental results on SimpleQuestions demonstrate the effectiveness of the proposed approach.     

蛋类礼盒包装结构的缓冲性能研究

目的研究蛋类礼盒包装结构的缓冲性能。方法以蛋类尺寸为基础,建立可发性聚乙烯(expandable polyethylene. EPE)缓冲单元结构和组合结构,进行静态仿真分析和实验验证,比较结构在形状、叠合层数、组合形式等参数变化时的载荷与位移。结果结构层数变化相同时,单元结构的极限载荷从143N增加到236 N,组合结构的极限载荷从224 N增加到476 N,均呈近线性增长。结论蛋类礼盒包装中,组合结构的承载能力优于单元结构,通过单元结构的组合,可满足不同蛋类的包装要求。     

日本新型二次电池工业发展及其与中国的比较

在新型二次电池产业的发展中,氢镍电池市场不断萎缩,锂离子电池市场正处于黄金时代。通过对日本和中国新型二次电池产业发展历程分析,我国主要针对低端市场,高端市场为日本占据,并从日本发展经验中提出了可供我国锂离子电动车电池发展的借鉴之处。     

Achieving Rich and Active Alkaline Hydrogen Evolution Heterostructures via Interface Engineering on 2D 1T‐MoS2 Quantum Sheets

Large‐scale production of hydrogen from water‐alkali electrolyzers is impeded by the sluggish kinetics of hydrogen evolution reaction (HER) electrocatalysts. The hybridization of an acid‐active HER catalyst with a cocatalyst at the nanoscale helps boost HER kinetics in alkaline media. Here, it is demonstrated that 1T–MoS₂ nanosheet edges (instead of basal planes) decorated by metal hydroxides form highly active ${\text{edge}}_{{\text{1T‐MoS}}_{\text{2}}}$/ ${\text{edge}}_{\text{Ni}{(\text{OH})}_{\text{2}}}$ heterostructures, which significantly enhance HER performance in alkaline media. Featured with rich ${\text{edge}}_{{\text{1T‐MoS}}_{\text{2}}}$/ ${\text{edge}}_{\text{Ni}{(\text{OH})}_{\text{2}}}$ sites, the fabricated 1T–MoS₂ QS/Ni(OH)₂ hybrid (quantum sized 1T–MoS₂ sheets decorated with Ni(OH)₂ via interface engineering) only requires overpotentials of 57 and 112 mV to drive HER current densities of 10 and 100 mA cm^?2, respectively, and has a low Tafel slope of 30 mV dec^?1 in 1 m KOH. So far, this is the best performance for MoS₂‐based electrocatalysts and the 1T–MoS₂ QS/Ni(OH)₂ hybrid is among the best‐performing non‐Pt alkaline HER electrocatalysts known. The HER process is durable for 100 h at current densities up to 500 mA cm^?2. This work not only provides an active, cost‐effective, and robust alkaline HER electrocatalyst, but also demonstrates a design strategy for preparing high‐performance catalysts based on edge‐rich 2D quantum sheets for other catalytic reactions.