Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

Single copper sites dispersed on hierarchically porous carbon for improving oxygen reduction reaction towards zinc-air battery

The demand for high-performance non-precious-metal electrocatalysts to replace the noble metal-based catalysts for oxygen reduction reaction(ORR)is intensively increasing.Herein,single-atomic copper sites supported on N-doped three-dimensional hierarchically porous carbon catalyst(Cu₁/NC)was prepared by coordination pyrolysis strategy.Remarkably,the Cu₁/NC-900 catalyst not only exhibits excellent ORR performance with a half-wave potential of 0.894 V(vs.RHE)in alkaline media,outperforming those of commercial Pt/C(0.851 V)and Cu nanoparticles anchored on N-doped porous carbon(CuNPs/NC-900),but also demonstrates high stability and methanol tolerance.Moreover,the Cu₁/NC-900 based Zn-air battery exhibits higher power density,rechargeability and cyclic stability than the one based on Pt/C.Both experimental and theoretical investigations demonstrated that the excellent performance of the as-obtained Cu₁/NC-900 could be attributed to the synergistic effect between copper coordinated by three N atoms active sites and the neighbouring carbon defect,resulting in elevated Cu d-band centers of Cu atoms and facilitating intermediate desorption for ORR process.This study may lead towards the development of highly efficient non-noble metal catalysts for applications in electrochemical energy conversion.     

Multicellular Tumor Spheroids (MCTS) as a 3D In Vitro Evaluation Tool of Nanoparticles

Multicellular tumor spheroid models (MCTS) are often coined as 3D in vitro models that can mimic the microenvironment of tissues. MCTS have gained increasing interest in the nano‐biotechnology field as they can provide easily accessible information on the performance of nanoparticles without using animal models. Considering that many countries have put restrictions on animals testing, which will only tighten in the future as seen by the recent developments in the Netherlands, 3D models will become an even more valuable tool. Here, an overview on MCTS is provided, focusing on their use in cancer research as most nanoparticles are tested in MCTS for treatment of primary tumors. Thereafter, various types of nanoparticles—from self‐assembled block copolymers to inorganic nanoparticles, are discussed. A range of physicochemical parameters including the size, shape, surface chemistry, ligands attachment, stability, and stiffness are found to influence nanoparticles in MCTS. Some of these studies are complemented by animal studies confirming that lessons from MCTS can in part predict the behaviour in vivo. In summary, MCTS are suitable models to gain additional information on nanoparticles. While not being able to replace in vivo studies, they can bridge the gap between traditional 2D in vitro studies and in vivo models.     

General Decay Synchronization and H ∞ Synchronization of Multi-weighted Coupled Reaction-diffusion Neural Networks

This paper investigates the general decay synchronization and general decay H∞ synchronization problems of multi-weighted coupled reaction-diffusion     

海面油膜的偏振反射特性仿真实验

为了给海面溢油污染识别检测提供理论基础,根据菲涅尔反射公式的偏振反射系数,结合偏振双向反射率因子和粗糙海面的概率密度分布函数,建立了完善的pBRDF模型,仿真在不同太阳入射角度、不同探测器观测角度以及不同海面风速风向等条件下海水和油膜的偏振反射分布函数。结果表明:海水和油膜太阳天顶角为53°和56°时P偏振反射率分别为1.0×10^-5和2.5×10^-5,S偏振反射率随着太阳天顶角的增加而增加;海面风速越大偏振反射率峰值越小;海面风向只改变pBRDF的空间位置;海水和油膜线偏振度空间分布有明显差异。搭建实验平台相机以40°拍摄时,得出海水和油膜的线偏振度分别在0.2~0.4, 0.5~0.7之间,同时表明利用偏振探测获取目标场景的偏振度和偏振角图可提高图像质量。     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Dandelion-Like Bi2S3/rGO hierarchical microspheres as high-performance anodes for potassium-ion and half/full sodium-ion batteries

Sodium-ion batteries (SIBs) and potassium-ion batteries (PIBs) have been considered as attractive alternatives for next-generation battery systems, which have promising application potential due to their earth abundance of potassium and sodium, high capacity and suitable working potential, however, the design and application of bi-functional high-performance anode still remain a great challenge up to date. Bismuth sulfide is suitable as anode owing to its unique laminar structure with relatively large interlayer distance to accommodate larger radius ions, high theoretical capacity and high volumetric capacity etc. In this study, dandelion-like Bi₂S₃/rGO hierarchical microspheres as anode material for PIBs displayed reversible capacity, and 206.91 mAh·g⁻¹ could be remained after 1,200 cycles at a current density of 100 mA·g⁻¹. When applied as anode materials for SIBs, 300 mAh·g⁻¹ could be retained after 300 cycles at 2 A·g⁻¹ and its initial Coulombic efficiency is as high as 97.43%. Even at high current density of 10 A·g⁻¹, 120.3 mAh·g⁻¹ could be preserved after 3,400 cycles. The Na₃V₂(PO₄)₃@rGO//Bi₂S₃/rGO sodium ion full cells were successfully assembled which displays stable performance after 60 cycles at 100 mA·g⁻¹. The above results demonstrate that Bi₂S₃/rGO has application potential as high performance bi-functional anode for PIBs and SIBs.

     

Adaptive neural network output feedback control of incommensurate fractional-order PMSMs with input saturation via command filtering and state observer

Neural Computing and Applications - In this paper, an adaptive neural network (NN) output feedback control is investigated for incommensurate fractional-order permanent magnet synchronous motors...     

Computational Fluid Dynamics Study on a Top-Blown Smelting Process with Lance Failure in an Isa Furnace

JOM - The Isa/Ausmelt smelting technology with a top submerged lance (TSL) has been extensively used in copper smelting processes. However, the TSL is extremely vulnerable to damage and failure...