Physicochemical and technological properties of beef burger as influenced by the addition of pea fibre

This study aimed to evaluate the physicochemical characteristics and sensory attributes of beef burgers with the addition of pea fibre as a partial substitute of meat or fat. Three formulations were prepared: control (CON) – similar to the commercial formulation; fibre/less meat (FLM)—5% meat reduction and addition of 1% pea fibre; fibre/less fat (FLF)—7% fat reduction and addition of 1% pea fibre. Non-significant differences were obtained for pH, colour parameters (L* and b*), texture profile, cooking loss and size reduction among formulations. Moreover, sensory analysis with consumers of beef burgers did not indicate differences among the formulations for all the analysed attributes. Therefore, pea fibre is a promising partial replacer for meat and fat in beef burgers due to the preservation of technological parameters and sensory acceptance.     

定距螺旋桨对船用主机外特性的要求分析

为解决定距螺旋桨与船用主机在船舶运行工况的机桨匹配问题,结合船舶系泊和航行试验的相关标准,分析和归纳船舶运行数据,将实船测试与船机桨匹配理论计算相结合,得出运输船和拖轮在常用工况及特殊工况下定距螺旋桨对主机外特性的定量要求,为配套不同细分市场时船用主机的优化和开发提供参考依据。     

Fuzzy set based cost model of additive manufacturing with specific example of selective laser sintering

A fuzzy set based cost model for additive manufacturing is proposed. The model is illustrated through an example of selective laser sintering (SLS), a commonly used additive manufacturing (AM) process. Initially, a deterministic cost model is developed. It is then converted to a fuzzy set based model by considering uncertainty in build time estimation and cost components. For the specific case of SLS, a build time estimation procedure is developed as a part of the cost model. A method to evaluate the reliability of the cost estimate in AM and its significance is also introduced. The cost model is illustrated through two examples of products manufactured by SLS.

     

Continuous Flow Fabrication of Block Copolymer–Grafted Silica Micro‐Particles in Environmentally Friendly Water/Ethanol Media

Polymer‐grafted inorganic particles (PGIPs) are attractive building blocks for numerous chemical and material applications. Surface‐initiated controlled radical polymerization (SI‐CRP) is the most feasible method to fabricate PGIPs. However, a conventional in‐batch reaction still suffers from several disadvantages, including time‐consuming purification processes, low grafting efficiency, and possible gelation problems. Herein, a facile method is demonstrated to synthesize block copolymer–grafted inorganic particles, that is, poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMEMA)‐b‐poly(N‐isopropylacrylamide) (PNIPAM)–grafted silica micro‐particles using continuous flow chemistry in an environmentally friendly aqueous media. Immobilizing the chain transfer agent and subsequent SI‐CRP can be accomplished sequentially in a continuous flow system, avoiding multi‐step purification processes in between. The chain length (MW) of the grafted polymers is tunable by adjusting the flow time or monomer concentration, and the narrower molar mass dispersity (Р< 1.4) of the grafted polymers reveals the uniform polymer chains on the particles. Moreover, compared with the in‐batch reaction at the same condition, the continuous system also suppresses possible gelation problems.     

Characterizations of friction welding joint interface for AISI 316

Because of heat amount is different from peripheral to central of friction welding interface, which is leaded to vary the characterizations along that interface. Current study, respectively, focused on the effect of different friction pressure on micro-structural and mechanical properties of that friction welding joint interface. Presently, these friction pressures are 110, 130, 150 and 170 MPa while kept all other conditions constant. The effects of different friction pressure on welding interface characterization were investigated by EDX, SEM, tensile, compression, impact and hardness tests. The tensile tests carried out on the standardized test piece with diameter 6 mm and 8 mm, thus, compression tests were extracted from the positions of 0°, 45° 90° with test specimen of 4 mm diameter and 6.5 mm length at weld center. Whereas, the impact test pieces were picked up in two positions, the first one is symmetrical, which it obtained to the respect of the rotation axis and the interface, on the other hand, the second one is non-symmetrical with the axis of rotation and symmetrical to the interface, for making the notch head coincide with the center of the welded joint, The obtained results showed that with reducing of friction pressure will present lack of bonding increasing from peripheral toward the welding center, which will responsible on reducing of the mechanical properties such as tensile, compression and impact strength.     

Increasing Volumetric CO2 Uptake of Hypercrosslinked Polymers through Composite Formation

To overcome the drawbacks of solid microporous materials for CO₂ capture, this proof‐of‐concept study demonstrates a low‐cost and rapid method for producing composites consisting of hypercrosslinked polymers (HCP) with a polyethyleneimine (PEI) binder. The resulting materials capture CO₂ through physical and chemical absorption simultaneously. Compared with HCP, the composites exhibit higher CO₂ uptake, higher volumetric density, and improved tolerance to water which is attributed to the PEI binder.